Nissan Juke (2012 year). Service Repair Manual — part 63
COMPONENT PARTS
DLN-13
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
NOTE:
The driving force distribution may not match actual one. This is not a system malfunction.
1.
Front right side driving torque
2.
Front left side driving torque
3.
Rear right side driving torque
4.
Rear left side driving torque
JSDIA2067ZZ
Revision: 2011 October
2012 JUKE
DLN-14
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
STRUCTURE AND OPERATION
STRUCTURE AND OPERATION
Sectional View
INFOID:0000000007580145
Operation Principle
INFOID:0000000007580146
POWER TRANSFER DIAGRAM
ELECTRIC CONTROLLED COUPLING
1.
Transfer cover
2.
Ring gear shaft
3.
Companion flange
4.
Drive pinion
5.
Ring gear
6.
Transfer case
JSDIA2068ZZ
1.
Engine
2.
Transaxle
3.
Transfer
4.
Propeller shaft
5.
Electric controlled coupling
6.
Rear final drive
JSDIA2069ZZ
Revision: 2011 October
2012 JUKE
STRUCTURE AND OPERATION
DLN-15
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
1.
The AWD control module supplies command current to each
electric controlled coupling (AWD solenoid).
2.
Each of control clutch is engaged by electromagnet and torque
is detected in control clutch.
3.
The cam operates in response to control clutch torque and
applies pressure to main clutch.
4.
Each of main clutch transmits torque to right and left rear wheels
according to pressing power.
NOTE:
Change each pressing power according to AWD mode status
and cornering conditions.
• Transmission torque to the right and left rear wheels is deter-
mined according to command current.
JSDIA2372GB
SDIA1844E
Revision: 2011 October
2012 JUKE
DLN-16
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
SYSTEM
SYSTEM
AWD SYSTEM
AWD SYSTEM : System Diagram
INFOID:0000000007580147
INPUT/OUTPUT SIGNAL
It transmits/receives each signal from the following AWD control module via CAN communication line.
JSDIA2373GB
Component parts
Signal item
ABS actuator and electric unit (control unit)·
Mainly transmits the following signals via CAN communication line to AWD control
module.
• Vehicle speed signal (ABS)
• Stop lamp switch signal (brake signal)
• Yaw rate signal
• Side G sensor signal
• Decel G sensor signal
ECM
Mainly transmits the following signals via CAN communication line to AWD control
module.
• Accelerator pedal position signal
• Engine speed signal
• Engine torque signal
TCM
Mainly transmits the following signals via CAN communication line to AWD control
module.
• Next gear position signal
• Current gear position signal
• Input shaft revolutional signal
• Output shaft revolutional signal
• CVT ratio signal
Revision: 2011 October
2012 JUKE
SYSTEM
DLN-17
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD SYSTEM : System Description
INFOID:0000000007580148
• AWD mode is selectable among 2WD, AWD-V, and AWD by operating the AWD mode switch.
• When judging driving conditions and road surface conditions based on signals transmitted from each sensor
and switch, the AWD system automatically controls torque distribution of front and rear wheels and both
front wheels, depending on the situation.
• In accordance with fail-safe function, when system is malfunctioning, AWD control stops, and the system
becomes front wheel drive. Refer to
DLN-18, "AWD SYSTEM : Fail-safe"
.
• When a high load status continues for electric controlled coupling, AWD control temporarily becomes front
wheel drive, according to protection function. Refer to
DLN-20, "AWD SYSTEM : Protection Function"
AWD SYSTEM : Torque Split Control
INFOID:0000000007580149
2WD mode
• Vehicle is in front-wheel drive.
AWD-V mode
Normal Control
• Pressing force of multiple disc clutch is controlled by electric control. Driving torque distribution of front and
rear wheels changes automatically between approximately 100 : 0 (Front wheel drive) and 50 : 50 (AWD) to
have an optimized torque distribution adapted to road condition change.
• When slip occurs on front wheel, distribute optimum torque to rear wheel and keep stable driving.
• On roads which do not require AWD, it contributes to improved fuel economy by driving in conditions close to
front-wheel drive and it results in better fuel efficiency.
Cornering Control
• Torque between both rear wheels is automatically changed between 100 : 0 and 0 : 100 for distributing opti-
mum torque that depends on the driving conditions and road surface conditions.
• Producing a difference between both rear wheels enables sporty and smooth handling.
Combination meter
Mainly transmits the following signals via CAN communication line to AWD control
module.
• Parking brake switch signal
Mainly receives the following signals via CAN communication line from AWD control
module.
• AWD warning lamp signal
• AWD mode indicator lamp signal
• Torque distribution indicator signal
Steering angle sensor
Mainly transmits the following signals via CAN communication line to AWD control
module.
• Steering angle sensor signal
Component parts
Signal item
JSDIA2071GB
Revision: 2011 October
2012 JUKE
DLN-18
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
SYSTEM
• The vehicle cornering status is judged according to information from each sensor, and the optimum torque is
distributed to rear wheels for preventing tight cornering/braking symptom.
AWD mode
• The AWD mode controls torque for obtaining suitable torque for driving on slippery roads (e.g. snow-covered
roads) and provides more stable driving, compared to AWD-V.
AWD SYSTEM : Fail-safe
INFOID:0000000007580150
When a system malfunction occurs, the AWD warning lamp turns ON and the AWD control becomes 2WD
state.
JSDIA2072GB
Detected
DTC
Possible cause
AWD warning
lamp status
Vehicle condition
P1804
Internal malfunction of AWD control module
OFF
Normal control continues.
P1808
• ABS actuator and electric unit (control unit)
- Malfunction of ABS actuator and electric unit (control unit) cir-
cuit error
- Wheel speed sensor error
• AWD control module
• CAN communication line
ON
Front and rear distribution control
stops.
P1809
Internal malfunction of AWD control module
P1811
• Malfunction of AWD control module power supply circuit (open
or short)
• Malfunction of AWD control module
• Battery
P1813
• AWD mode switch
- Internal malfunction of AWD mode switch
- Malfunction of AWD mode switch circuit
• AWD control module
P181B
Self-shut of AWD control module is incomplete.
OFF
Normal control continues.
P181D
• ECM
• AWD control module
• CAN communication line
ON
Front and rear distribution control
stops.
NOTE:
The state becomes AWD only when
a turning difference occurs between
front and rear wheels.
P181E
• Steering angle sensor
- Steering angle sensor error
- Malfunction of steering angle sensor circuit
• Malfunction of AWD control module
• CAN communication line
OFF
Right and left rear wheels difference
control stops.
P181F
Writing unit characteristics is incomplete.
ON
Front and rear distribution control
stops.
P1820
• ECM
• AWD control module
• CAN communication line
OFF
Normal control continues.
Revision: 2011 October
2012 JUKE
SYSTEM
DLN-19
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1829
• ECM
• AWD control module
• CAN communication line
ON
Front and rear distribution control
stops.
P182D
• Internal malfunction of electric controlled coupling (left)
• Malfunction of AWD solenoid (left) power supply circuit (open
or short)
• Malfunction of AWD control module
P182E
• Internal malfunction of electric controlled coupling (right)
• Malfunction of AWD solenoid (right) power supply circuit (open
or short)
• Malfunction of AWD control module
P182F
• Electric controlled coupling (left) temperature sensor
- Internal malfunction of electric controlled coupling (left) tem-
perature sensor
- Malfunction of electric controlled coupling (left) temperature
sensor circuit (open or short)
• Malfunction of AWD control module
OFF
Normal control continues.
P1830
• ABS actuator and electric unit (control unit)
• AWD control module
• CAN communication line
P1831
• ABS actuator and electric unit (control unit)
• AWD control module
• CAN communication line
P1832
• ABS actuator and electric unit (control unit)
• AWD control module
• CAN communication line
P183A
• Electric controlled coupling (right) temperature sensor
- Internal malfunction of electric controlled coupling (right) tem-
perature sensor
- Malfunction of electric controlled coupling (right) temperature
sensor circuit (open or short)
• Malfunction of AWD control module
P183B
• Malfunction of AWD solenoid power supply circuit
• Malfunction of AWD control module
• Malfunction of AWD control module power supply circuit (open
or short)
• Battery
ON
Front and rear distribution control
stops.
Detected
DTC
Possible cause
AWD warning
lamp status
Vehicle condition
Revision: 2011 October
2012 JUKE
DLN-20
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
SYSTEM
AWD SYSTEM : Protection Function
INFOID:0000000007580151
AWD system activates its protection function (shuts down AWD system temporarily) if AWD system detects
high load continuously, the front wheel tire size differs from the rear tire size or the rear right wheel tire size dif-
fers from the rear left tire size. (AWD system is automatically restored if AWD system no longer detects any
overload or the tire size difference is eliminated.)
*1: 2 times/second (blinking for approximately 1 minute and then turned OFF)
*2: 1 time/2 seconds (continuing to blink until ignition switch is turned OFF)
NOTE:
• If the warning lamp blinks slowly during driving but remains OFF after the engine is restarted, the system is
normal. If it again blinks slowly after driving for some time, vehicle must be inspected.
• When there is a difference of revolution speed between the front and rear wheel the shift occasionally
changes to direct 4-wheel driving conditions automatically. This is not a malfunction.
P183C
• ABS actuator and electric unit (control unit)
• Yaw rate/side/decel G sensor (Decel G sensor signal)
• AWD control module
• CAN communication line
OFF
Right and left rear wheels difference
control stops.
P183D
• ABS actuator and electric unit (control unit)
• Yaw rate/side/decel G sensor (Side G senesor signal)
• AWD control module
• CAN communication line
P183E
• ABS actuator and electric unit (control unit)
• Yaw rate/side/decel G sensor (Yaw rate signal)
• AWD control module
• CAN communication line
P183F
• Sensor related to CVT
• TCM
• AWD control module
• CAN communication line
P1840
• Sensor related to CVT
• TCM
• AWD control module
• CAN communication line
P1864
• Sensor related to CVT
• TCM
• AWD control module
• CAN communication line
P1865
• Sensor related to CVT
• TCM
• AWD control module
• CAN communication line
U1000
CAN communication error
ON
Front and rear distribution control
stops.
U1010
Internal malfunction of AWD control module
Detected
DTC
Possible cause
AWD warning
lamp status
Vehicle condition
Detected
DTC
Warning lamp
Possible cause
Vehicle condition
—
Quick blinking
*1
Turning difference remains between front and rear wheels or between
right and left rear wheels, resulting in an oil temperature rise in drive train
related parts.
NOTE:
It is not malfunction.
Shuts down AWD system
temporarily
—
Slow blinking
*2
Malfunction in each tire or different tire diameter
Revision: 2011 October
2012 JUKE
DIAGNOSIS SYSTEM (AWD CONTROL MODULE)
DLN-21
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DIAGNOSIS SYSTEM (AWD CONTROL MODULE)
CONSULT Function
INFOID:0000000007580152
APPLICATION ITEMS
CONSULT can display each diagnostic item using the diagnostic test modes as follows.
*: The following diagnosis information is erased by erasing.
• DTC
• Freeze frame data (FFD)
ECU IDENTIFICATION
AWD control module part number can be read.
SELF DIAGNOSTIC RESULT
.
When “PRSNT” is displayed on self-diagnosis result.
• The system is presently malfunctioning.
When “PAST” is displayed on self-diagnosis result.
• System malfunction in the past is detected, but the system is presently normal.
FREEZE FRAME DATA (FFD)
The following vehicle status is recorded when DTC is detected and is displayed.
Diagnostic test mode
Function
ECU Identification
AWD control module part number can be read.
Self Diagnostic Result
Self-diagnostic results and freeze frame data can be read and erased quickly.*
Data Monitor
Input/Output data in the AWD control module can be read.
Active Test
Diagnostic Test Mode in which CONSULT drives some actuators apart from the AWD control mod-
ule and also shifts some parameters in a specified range.
Work support
This mode enable a technican to adjust some devices faster and more accurately by following the
indication on the CONSULT.
Freeze Frame Data Item
Description
SOLENOID VOLT
Power supply voltage of AWD solenoid is displayed.
TRGT SOL CRNT LH
AWD solenoid (left) target current is displayed.
SOLENOID CRNT LH
AWD solenoid (left) control current is displayed.
TRGT SOL CRNT RH
AWD solenoid (right) target current is displayed.
SOLENOID CRNT RH
AWD solenoid (right) control current is displayed.
COMPR VHCL SPEED
Vehicle speed calculated by AWD control module is displayed.
VHCL/S SEN-FR
Vehicle speed (front) average calculated by AWD control module is displayed.
VHCL/S SEN-RR
Vehicle speed (rear) average calculated by AWD control module is displayed.
WHEEL SPD SEN FR
Wheel speed (front right) calculated by AWD control module is displayed.
WHEEL SPD SEN FL
Wheel speed (front left) calculated by AWD control module is displayed.
WHEEL SPD SEN RR
Wheel speed (rear right) calculated by AWD control module is displayed.
WHEEL SPD SEN RL
Wheel speed (rear left) calculated by AWD control module is displayed.
ABS OPERATION SIG
ABS operation status via CAN communication line is displayed.
VDC OPERATION SIG
VDC operation status via CAN communication line is displayed.
TCS OPERATION SIG
TCS operation status via CAN communication line is displayed.
HIGH M FLG 1 [0/1]
Measured friction of load is displayed when vehicle starts.
• When “0” is displayed: It indicates that friction of load is not high.
• When “1” is displayed: It indicates that friction of load is high.
Revision: 2011 October
2012 JUKE
DLN-22
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
DIAGNOSIS SYSTEM (AWD CONTROL MODULE)
DATA MONITOR
X: Applicable
HIGH M FLG 2 [0/1]
Measured friction of load is displayed when vehicle throttles down.
• When “0” is displayed: It indicates that friction of load is not high.
• When “1” is displayed: It indicates that friction of load is high.
SLCT LVR POSI
Current transmission gear via CAN communication line is displayed.
OPERATION MODE
Control status of AWD mode is displayed.
IGN COUNTER [0 - 39]
The number of times that ignition switch is turned ON after the DTC is detected is displayed.
• When “0” is displayed: It indicates that the system is presently malfunctioning.
• When except “0” is displayed: It indicates that system malfunction in the past is detected, but the
system is presently normal.
NOTE:
Each time when ignition switch is turned OFF to ON, numerical number increases in
1
→
2
→
3...38
→
39.
When the operation number of times exceeds 39, the number do not increase and “39” is displayed
until self-diagnosis is erased.
Freeze Frame Data Item
Description
Monitor item [Unit]
SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALS
MAIN SIG-
NALS
SWITCH 1 [On/Off]
X
AWD mode switch status (2WD) is displayed.
SWITCH 2 [On/Off]
X
AWD mode switch status (AWD-V or AWD) is displayed.
SWITCH 3 [On/Off]
X
AWD mode switch status (AWD) is displayed.
IGN SW [On/Off]
X
Ignition switch status is displayed.
WARNING LAMP [On/Off]
X
Control status of AWD warning lamp is displayed.
R POSITION SW [On/Off]
X
X
CVT shift selector is displayed.
ABS OPERATION SIG [On/Off]
ABS operation status via CAN communication line is dis-
played.
VDC OPERATION SIG [On/Off]
VDC operation status via CAN communication line is dis-
played.
TCS OPERATION SIG [On/Off]
TCS operation status via CAN communication line is dis-
played.
PKB SW [On/Off]
X
Parking brake switch signal status via CAN communica-
tion line is displayed.
STOP LAMP SW [On/Off]
X
Stop lamp switch signal status via CAN communication
line is displayed.
4WD MODE SW [2WD/4WD-A]
X
AWD mode switch status is displayed.
ACTUATOR RELAY [On/Off]
AWD actuator relay (integrated in AWD control module)
operation status is displayed.
OPERATION MODE [2WD/4WD-V/
4WD-A]
X
Control status of AWD mode is displayed.
INDICATOR [2WD/4WD-V/4WD-A]
X
Control status of AWD mode indicator lamp is displayed.
DRIVE MODE [1/2]
X
AWD mode status is displayed.
TORQU DISTR RR LH [1/1-2/1-3/1-4/
OFF]
Control status of torque distribution indicator (rear left) is
displayed.
TORQU DISTR RR RH [1/1-2/1-3/1-4/
OFF]
Control status of torque distribution indicator (rear right)
is displayed.
TORQU IND FRONT [1/1-2/1-3/1-4/
OFF]
Control status of torque distribution indicator (front) is dis-
played.
TEMP SEN LEFT [V]
X
Voltage of electric controlled coupling temperature sen-
sor (left) is displayed.
TEMP SEN RIGHT [V]
X
Voltage of electric controlled coupling temperature sen-
sor (right) is displayed.
Revision: 2011 October
2012 JUKE
DIAGNOSIS SYSTEM (AWD CONTROL MODULE)
DLN-23
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ACTIVE TEST
Use this mode to determine and identify the details of a malfunction based on self-diagnostic results or data
monitor. AWD control module gives drive signal to actuator with receiving command from CONSULT to check
operation of actuator.
CAUTION:
Never energize continuously for a long time.
CONT MODUL VOLT [V]
X
Power supply voltage of AWD control module is dis-
played.
SOLENOID VOLT [V]
X
Power supply voltage of AWD solenoid is displayed.
TRGT SOL CRNT LH [A]
X
AWD solenoid (left) target current is displayed.
SOLENOID CRNT LH [A]
X
AWD solenoid (left) control current is displayed.
TRGT SOL CRNT RH [A]
X
AWD solenoid (right) target current is displayed.
SOLENOID CRNT RH [A]
X
AWD solenoid (right) control current is displayed.
COMPR VHCL SPEED [km/h] or [MPH]
X
Vehicle speed calculated by AWD control module is dis-
played.
VHCL/S SEN-FR [km/h] or [MPH]
Vehicle speed (front) average calculated by AWD control
module is displayed.
VHCL/S SEN-RR [km/h] or [MPH]
Vehicle speed (rear) average calculated by AWD control
module is displayed.
THRTL POS SEN [%]
Accelerator pedal status via CAN communication line is
displayed.
SLCT LVR POSI [2ND / 3RD / 4TH / 5TH
/ 6TH / 7TH / 8TH / R / N/P / D]
X
Current transmission gear via CAN communication line is
displayed.
TRGT DRIVE TORQU [Nm]
Request drive torque from AWD control module to ECM
is displayed.
RQST DRIVE TORQU [Nm]
Request drive torque from ABS actuator and electric unit
(control unit) to AWD control module is displayed.
WHEEL SPD SEN FR [km/h] or [MPH]
Wheel speed (front right) calculated by AWD control
module is displayed.
WHEEL SPD SEN FL [km/h] or [MPH]
Wheel speed (front left) calculated by AWD control mod-
ule is displayed.
WHEEL SPD SEN RR [km/h] or [MPH]
Wheel speed (rear right) calculated by AWD control mod-
ule is displayed.
WHEEL SPD SEN RL [km/h] or [MPH]
Wheel speed (rear left) calculated by AWD control mod-
ule is displayed.
Monitor item [Unit]
SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALS
MAIN SIG-
NALS
Test item
Condition
Description
SOLENOID LEFT
• Vehicle stopped
• Engine running
• No DTC detected
Change command current value to AWD solenoid (left), and then change driv-
ing mode. (Monitor value is normal if it is within approx.
±
10% of command
value.)
• Qu: Increase current value in increments of 0.2 A
• Qd: Decrease current value in increments of 0.2 A
• UP: Increase current value in increments of 0.02 A
• DOWN: Decrease current value in increments of 0.02 A
SOLENOID RIGHT
• Vehicle stopped
• Engine running
• No DTC detected
Change command current value to AWD solenoid (right), and then change
driving mode. (Monitor value is normal if it is within approx.
±
10% of command
value.)
• Qu: Increase current value in increments of 0.2 A
• Qd: Decrease current value in increments of 0.2 A
• UP: Increase current value in increments of 0.02 A
• DOWN: Decrease current value in increments of 0.02 A
Revision: 2011 October
2012 JUKE
DLN-24
< SYSTEM DESCRIPTION >
[TRANSFER: TY21B]
DIAGNOSIS SYSTEM (AWD CONTROL MODULE)
WORK SUPPORT
Item
Usage
UNIT CHARACTERISTICS DATA
Display the unit characteristics of electric controlled coupling written to AWD control module.
UNIT CHARACTERISTICS WRITE
Writes the unit characteristics of electric controlled coupling to AWD control module.
Revision: 2011 October
2012 JUKE
AWD CONTROL MODULE
DLN-25
< ECU DIAGNOSIS INFORMATION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ECU DIAGNOSIS INFORMATION
AWD CONTROL MODULE
Reference Value
INFOID:0000000007580153
VALUES ON THE DIAGNOSIS TOOL
Monitor item
Condition
Value/Status
SWITCH 1
AWD mode switch: 2WD
On
AWD mode switch: AWD-V or AWD
Off
SWITCH 2
AWD mode switch: AWD-V or AWD
On
AWD mode switch: 2WD
Off
SWITCH 3
AWD mode switch: AWD
On
AWD mode switch: 2WD or AWD-V
Off
IGN SW
Ignition switch: ON
On
Ignition switch: OFF
Off
WARNING LAMP
AWD warning lamp: ON
On
AWD warning lamp: OFF
Off
R POSITION SW
CVT shift selector: R
On
CVT shift selector: Except R
Off
ABS OPERATION SIG
ABS is operating
On
ABS is not operating
Off
VDC OPERATION SIG
VDC is operating
On
VDC is not operating
Off
TCS OPERATION SIG
TCS is operating
On
TCS is not operating
Off
PKB SW
Parking brake is operated
On
Parking brake is not operated
Off
STOP LAMP SW
Brake pedal is depressed
On
Brake pedal is released
Off
4WD MODE SW
AWD mode switch: 2WD
2WD
AWD mode switch: AWD-V or AWD
4WD-A
ACTUATOR RELAY
Engine stopped (Ignition switch: ON)
Off
Engine running
On
OPERATION MODE
2WD mode
2WD
AWD-V mode
4WD-V
AWD mode
4WD-A
INDICATOR
AWD mode indicator (AWD-V): OFF
AWD mode indicator (AWD): OFF
2WD
AWD mode indicator (AWD-V): ON
AWD mode indicator (AWD): OFF
4WD-V
AWD mode indicator (AWD-V): ON
AWD mode indicator (AWD): ON
4WD-A
DRIVE MODE
Except AWD mode
1
AWD mode
2
Revision: 2011 October
2012 JUKE
DLN-26
< ECU DIAGNOSIS INFORMATION >
[TRANSFER: TY21B]
AWD CONTROL MODULE
TORQU DISTR RR LH
The number of bars of torque distribution indicator (rear LH): 0
OFF
The number of bars of torque distribution indicator (rear LH): 1
1
The number of bars of torque distribution indicator (rear LH): 2
1-2
The number of bars of torque distribution indicator (rear LH): 3
1-3
The number of bars of torque distribution indicator (rear LH): 4
1-4
TORQU DISTR RR RH
The number of bars of torque distribution indicator (rear RH): 0
OFF
The number of bars of torque distribution indicator (rear RH): 1
1
The number of bars of torque distribution indicator (rear RH): 2
1-2
The number of bars of torque distribution indicator (rear RH): 3
1-3
The number of bars of torque distribution indicator (rear RH): 4
1-4
TORQU IND FRONT
The number of bars of torque distribution indicator (front): 0
OFF
The number of bars of torque distribution indicator (front): 1
1
The number of bars of torque distribution indicator (front): 2
1-2
The number of bars of torque distribution indicator (front): 3
1-3
The number of bars of torque distribution indicator (front): 4
1-4
TEMP SEN LEFT
Temperature of electric controlled coupling (left) is 10
°
C (50
°
F)
Aprrox. 3.5 V
Temperature of electric controlled coupling (left) is 20
°
C (68
°
F)
Aprrox. 3.2 V
Temperature of electric controlled coupling (left) is 30
°
C (86
°
F)
Aprrox. 2.8 V
TEMP SEN RIGHT
Temperature of electric controlled coupling (right) is 10
°
C (50
°
F)
Aprrox. 3.5 V
Temperature of electric controlled coupling (right) is 20
°
C (68
°
F)
Aprrox. 3.2 V
Temperature of electric controlled coupling (right) is 30
°
C (86
°
F)
Aprrox. 2.8 V
CONT MODUL VOLT
Always
11 – 13 V
SOLENOID VOLT
Always
11 – 13 V
TRGT SOL CRNT LH
Vehicle stopped
0.00 A
Vehicle starting
(Straight-ahead start on a dry road with accelerator angle 25%)
NOTE:
Confirm accelerator angle in monitor item “THRTL POS SEN”.
Approx. 1.00 A
SOLENOID CRNT LH
Vehicle stopped
0.00 A
Vehicle starting
(Straight-ahead start on a dry road with accelerator angle 25%)
NOTE:
Confirm accelerator angle in monitor item “THRTL POS SEN”.
Approx. 1.00 A
TRGT SOL CRNT RH
Vehicle stopped
0.00 A
Vehicle starting
(Straight-ahead start on a dry road with accelerator angle 25%)
NOTE:
Confirm accelerator angle in monitor item “THRTL POS SEN”.
Approx. 1.00 A
SOLENOID CRNT RH
Vehicle stopped
0.00 A
Vehicle starting
(Straight-ahead start on a dry road with accelerator angle 25%)
NOTE:
Confirm accelerator angle in monitor item “THRTL POS SEN”.
Approx. 1.00 A
COMPR VHCL SPEED
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition.
Approx. equal to the indication on
speedometer (inside of
±
10%)
Monitor item
Condition
Value/Status
Revision: 2011 October
2012 JUKE
AWD CONTROL MODULE
DLN-27
< ECU DIAGNOSIS INFORMATION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
TERMINAL LAYOUT
VHCL/S SEN-FR
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition.
Approx. equal to the indication on
speedometer (inside of
±
10%)
VHCL/S SEN-RR
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition.
Approx. equal to the indication on
speedometer (inside of
±
10%)
THRTL POS SEN
When depressing accelerator pedal
(Value rises gradually in response to accelerator pedal position)
0 - 100%
SLCT LVR POSI
Engine running
CVT shift selector: Manual
mode
1ST
2ND
3RD
4TH
5TH
6TH
7TH
8TH
CVT shift selector: R
REVERSE
CVT shift selector: N or P
N/P
CVT shift selector: D
D
TRGT DRIVE TORQU
Request from AWD control module to ECM.
0 - 507 Nm
No request from AWD control module to ECM.
508 Nm
RQST DRIVE TORQU
Request from ABS actuator and electric unit (control unit) to
AWD control module.
0 - 1274 Nm
No request from ABS actuator and electric unit (control unit) to
AWD control module.
1275 Nm
WHEEL SPD SEN FR
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition.
Approx. equal to the indication on
speedometer (inside of
±
10%)
WHEEL SPD SEN FL
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition.
Approx. equal to the indication on
speedometer (inside of
±
10%)
WHEEL SPD SEN RR
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition.
Approx. equal to the indication on
speedometer (inside of
±
10%)
WHEEL SPD SEN RL
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition.
Approx. equal to the indication on
speedometer (inside of
±
10%)
Monitor item
Condition
Value/Status
Revision: 2011 October
2012 JUKE
DLN-28
< ECU DIAGNOSIS INFORMATION >
[TRANSFER: TY21B]
AWD CONTROL MODULE
PHYSICAL VALUES
JSDIA2078ZZ
Terminal No.
(Wire color)
Description
Condition
Value (Approx.)
+
-
Signal name
Input/
Output
1
(GR)
Ground
Battery power supply
(AWD control module)
Input
Always
11 - 13 V
3
(LG)
Ground
Ignition power supply
Input
Ignition switch: ON
11 - 13 V
Ignition switch: OFF
0 V
4
(L)
—
CAN-H
Input/
Output
—
—
5
(P)
—
CAN-L
Input/
Output
—
—
6
(SB)
Ground
Electric controlled coupling
(right) temperature sensor
power supply.
Output
Ignition switch: ON
5 V
Ignition switch: OFF
0 V
7
(P)
Ground
Electric controlled coupling
(right) temperature sensor
signal.
Input
When rear final drive
assembly tempera-
ture is the same as
room temperature.
Electric controlled coupling
(right) temperature: 10
°
C (50
°
F)
3.5 V
Electric controlled coupling
(right) temperature: 20
°
C (68
°
F)
3.2 V
Electric controlled coupling
(right) temperature: 30
°
C (86
°
F)
2.8 V
9
(W)
Ground
AWD mode switch (Except
2WD)
Input
Ignition switch: ON
AWD mode switch: 2WD
4.5 - 5 V
AWD mode switch: AWD-V or
AWD
0 V
10
(B)
Ground
Ground
—
Always
0 V
11
(B)
Ground
Ground
—
Always
0 V
12
(Y)
Ground
Battery power supply
(AWD solenoid)
Input
Always
11 - 13 V
13
(G)
Ground
AWD mode switch (2WD)
Input
Ignition switch: ON
AWD mode switch: 2WD
0 V
AWD mode switch: AWD-V or
AWD
4.5 - 5 V
16
(G)
Ground
Electric controlled coupling
(left) temperature sensor
signal.
Input
When rear final drive
assembly tempera-
ture is the same as
room temperature.
Electric controlled coupling (left)
temperature: 10
°
C (50
°
F)
3.5 V
Electric controlled coupling (left)
temperature: 20
°
C (68
°
F)
3.2 V
Electric controlled coupling (left)
temperature: 30
°
C (86
°
F)
2.8 V
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст