Nissan Juke (2012 year). Service Repair Manual — part 164
LU-8
< PERIODIC MAINTENANCE >
[MR16DDT ]
ENGINE OIL
2.
Disconnect harness connector at oil pressure sensor (1), and
remove oil pressure sensor using a deep socket (commercial
service tool).
CAUTION:
Never drop or shock oil pressure sensor.
3.
Install oil pressure gauge [SST: ST25051001 (J-25695-1)] (A)
and hose [SST: ST25052000 (J-25695-2)] (B).
4.
Start engine and warm it up to normal operating temperature.
5.
Check oil pressure with engine running under no-load.
NOTE:
When engine oil temperature is low, engine oil pressure becomes high.
If difference is extreme, check oil passage and oil pump for oil leakage.
6.
After the inspections, install oil pressure sensor as follows:
a.
Remove old liquid gasket adhering to oil pressure sensor and engine.
b.
Apply liquid gasket and tighten oil pressure sensor to specification.
Use Genuine RTV Silicon Sealant or equivalent.
c.
Check engine oil level.
d.
After warming up engine, check that there is no leakage of engine oil with running engine.
Draining
INFOID:0000000007579613
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Warm up the engine, and check for engine oil leakage from engine components. Refer to
2.
Stop the engine and wait for 10 minutes.
3.
Loosen oil filler cap.
4.
Remove drain plug and then drain engine oil.
2
: Starter motor
: Engine front
JPBIA4449ZZ
JPBIA0074ZZ
Engine oil pressure
: Refer to
Tightening torque
: Refer to
.
Revision: 2011 October
2012 JUKE
ENGINE OIL
LU-9
< PERIODIC MAINTENANCE >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
Refilling
INFOID:0000000007579614
1.
Install drain plug with new drain plug washer. Refer to
CAUTION:
Be sure to clean drain plug and install with new drain plug washer.
2.
Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-10, "Fluids and Lubricants"
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3.
Warm up engine and check area around drain plug and oil filter for engine oil leakage.
4.
Stop engine and wait for 10 minutes.
5.
Check the engine oil level. Refer to
.
Tightening torque
: Refer to
.
Engine oil capacity
: Refer to
LU-17, "Periodical Maintenance Specification"
Revision: 2011 October
2012 JUKE
LU-10
< PERIODIC MAINTENANCE >
[MR16DDT ]
OIL FILTER
OIL FILTER
Removal and Installation
INFOID:0000000007579615
REMOVAL
1.
Remove engine under cover.
2.
Using oil filter wrench [SST: KV10115801 (J-38956)] (A), remove
oil filter.
CAUTION:
• Oil filter is provided with relief valve. Use genuine NISSAN
oil filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1.
Remove foreign materials adhering to the oil filter installation surface.
2.
Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3.
Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to specification.
Inspection
INFOID:0000000007579616
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check that there is no leakage of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
: Vehicle front
JPBIA4450ZZ
SMA010
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
Revision: 2011 October
2012 JUKE
OIL COOLER
LU-11
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
REMOVAL AND INSTALLATION
OIL COOLER
Exploded View
INFOID:0000000007579617
M/T models
JPBIA4444GB
1.
Clamp
2.
Water hose
3.
Oil cooler
4.
Water hose
: N·m (kg-m, in-lb)
Revision: 2011 October
2012 JUKE
LU-12
< REMOVAL AND INSTALLATION >
[MR16DDT ]
OIL COOLER
CVT models
Removal and Installation
INFOID:0000000007579618
REMOVAL
1.
Drain engine coolant. Refer to
CAUTION:
Perform when engine is cold.
2.
Remove front bumper. Refer to
3.
Remove charge air cooler. Refer to
4.
Remove water hose.
5.
Remove oil cooler.
INSTALLATION
Installation is in reverse order of removal.
Inspection
INFOID:0000000007579619
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler assembly.
JPBIA4445GB
1.
Clamp
2.
Water hose
3.
Oil cooler
4.
Water hose
5.
Water hose
6.
Heater thermostat
A.
To CVT oil warmer
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
Revision: 2011 October
2012 JUKE
OIL COOLER
LU-13
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to
.
2.
Start the engine, and check that there is no leakage of engine oil or engine coolant.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level and the engine coolant level again. Refer to
and
Revision: 2011 October
2012 JUKE
LU-14
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
OIL PUMP
UNIT DISASSEMBLY AND ASSEMBLY
OIL PUMP
Exploded View
INFOID:0000000007579620
1.
O-ring
2.
Oil pan (upper)
3.
Oil level gauge guide
4.
O-ring
5.
Oil level gauge
6.
Oil pump drive chain
7.
Crankshaft sprocket
8.
Oil pump sprocket
9.
Oil pump chain tensioner
10. Oil pump
11.
Drain plug
12. Drain plug washer
13. Oil pan (lower)
14. Oil filter
15. Connector bolt
16. Clamp
17. Oil cooler hose
18. Oil cooler
19. Crankshaft position sensor
20. Gasket
21. Oil pan bolt
22. Rear oil seal
A.
Refer to
B.
To thermostat housing
C.
To thermostat housing (M/T models)
To CVT oil warmer (CVT models)
D.
Oil pan side
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JPBIA4875GB
Revision: 2011 October
2012 JUKE
OIL PUMP
LU-15
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
Removal and Installation
INFOID:0000000007579621
REMOVAL
1.
Remove engine assembly. Refer to
(2WD) ,
(AWD).
2.
Remove oil pan (lower). Refer to
EM-44, "Removal and Installation"
3.
Remove front cover, and other related parts. Refer to
4.
Remove oil pump sprocket with the following procedure:
• Add matching mark if necessary for easier installation.
a.
Push oil pump drive chain tensioner (1) in the direction show in
the figure.
b.
Insert a stopper pin (A) into the body hole (B).
c.
Remove oil pump chain tensioner.
• When the holes on lever and tensioner body cannot be
aligned, align these holes by slightly moving the oil pump
chain tensioner slack guide.
d.
Hold the WAF part of oil pump shaft [WAF: 10 mm (0.39 in)] (A),
and then loosen the oil pump sprocket bolt and remove it.
CAUTION:
• Secure the oil pump shaft with the WAF part.
• Never loosen the oil pump sprocket bolt by tightening the
oil pump drive chain.
e.
Remove oil pump sprocket.
5.
Remove oil pump.
: Should be lubricated with oil.
: Sealing point
: Indicates that the parts is connected at points with same symbols in actual vehicle.
JPBIA4397ZZ
1
: Oil pan (upper)
: Engine front
JPBIA4398ZZ
Revision: 2011 October
2012 JUKE
LU-16
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
OIL PUMP
• Loosen bolts in reverse order as shown in the figure.
INSTALLATION
Note the following, and install in the reverse order of removal.
Oil Pump
• Tighten bolts in numerical order as shown in the figure.
Inspection
INFOID:0000000007579622
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check that there is no leakage of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
1
: Oil pump
2
: Oil pan (upper)
: Engine front
JPBIA4451ZZ
1
: Oil pump
2
: Oil pan (upper)
: Engine front
JPBIA4451ZZ
Revision: 2011 October
2012 JUKE
SERVICE DATA AND SPECIFICATIONS (SDS)
LU-17
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000007579623
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
Engine Oil Pressure
INFOID:0000000007579624
Unit: kPa (kg/cm
2
, psi)
*: Engine oil temperature at 80
°
C (176
°
F)
Drain and refill
With oil filter change
4.5 (4-6/8, 4)
Without oil filter change
4.3 (4-4/8, 3-6/8)
Dry engine (Overhaul)
5.4 (5-6/8, 4-6/8)
Engine speed
Approximate discharge pressure*
Idle speed
90 (0.92, 13.1)
2,000 rpm
260 (2.65, 37.7)
Revision: 2011 October
2012 JUKE
MIR-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
MIR
A
B
MIR
N
O
P
CONTENTS
MIRRORS
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ..
Commercial Service Tools . . . . . . . . . ...
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Description . . . . . . . . . . .....
WIRING DIAGRAM . . . . . . . . . ...
DOOR MIRROR SYSTEM . . . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . .....
DTC/CIRCUIT DIAGNOSIS . . . . . . ..
DOOR MIRROR REMOTE CONTROL
SWITCH (MIRROR SWITCH/CHANGEOVER
SWITCH) . . . . . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . ...
Work Flow . . . . . . . . . . . . . . . . .
Inspection Procedure . . . . . . . . . . . ....
Diagnostic Worksheet . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
INSIDE MIRROR . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
OUTSIDE MIRROR . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
DOOR MIRROR ASSEMBLY . . . . . . . . .
DOOR MIRROR ASSEMBLY : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
GLASS MIRROR . . . . . . . . . . . . . .
GLASS MIRROR : Removal and Installation . . ...
DOOR MIRROR COVER . . . . . . . . . . ...
DOOR MIRROR COVER : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
DOOR MIRROR REMOTE CONTROL
SWITCH . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2011 October
2012 JUKE
MIR-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007578716
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2011 October
2012 JUKE
PREPARATION
MIR-3
< PREPARATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000007578717
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000007578718
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rat-
tle Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Remover tool
Removes the clips, pawls and metal clips
JMKIA3050ZZ
Revision: 2011 October
2012 JUKE
MIR-4
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Description
INFOID:0000000007578719
Item
Function
Door mirror remote control switch (mir-
ror switch)
It supplies power to mirror motor through mirror switch and changeover switch.
Door mirror remote control switch
(changeover switch)
It transmits the LH/RH control of door mirror that supplies power.
Door mirror motor
It makes mirror face operate from side to side and up and down via integrated motor.
Revision: 2011 October
2012 JUKE
DOOR MIRROR SYSTEM
MIR-5
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
WIRING DIAGRAM
DOOR MIRROR SYSTEM
Wiring Diagram
INFOID:0000000007578720
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWA4297GB
Revision: 2011 October
2012 JUKE
MIR-6
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
Component Inspection
INFOID:0000000007578721
1.
CHECK MIRROR SWITCH & CHANGEOVER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch.
Door mirror remote control switch
condition
Continuity
Terminal
Chenge over
switch
Mirror switch
Driver side
13
6
LEFT
RIGHT
Existed
12
5
13
5
LEFT
12
6
13
2
UP
12
6
13
6
DOWN
12
2
Passenger side
13
7
RIGHT
RIGHT
12
4
13
4
LEFT
12
7
13
3
UP
12
7
13
7
DOWN
12
3
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст