Nissan Murano Z50 (2005 year). Manual — part 175
CAN SYSTEM (TYPE 10)
LAN-413
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect ECM connector.
2.
Check resistance between ECM harness connector M80 termi-
nals 94 (L) and 86 (Y).
OK or NG
OK
>> Replace ECM.
NG
>> Repair harness between ECM and BCM.
Intelligent Key Unit Circuit Inspection
AKS00CHZ
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of Intelligent Key unit for damage, bend and loose connection (control
module side and harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect Intelligent Key unit connector.
2.
Check resistance between Intelligent Key unit harness connec-
tor M99 terminals 2 (L) and 3 (Y).
OK or NG
OK
>> Replace Intelligent Key unit.
NG
>> Repair harness between Intelligent Key unit and BCM.
TCM Circuit Inspection
AKS00CI0
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check following terminals and connectors for damage, bend and loose connection (control module side
and harness side).
–
TCM connector
–
Harness connector F102
–
Harness connector M82
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
94 (L) - 86 (Y)
: Approx. 108 - 132
Ω
SKIA6865E
2 (L) - 3 (Y)
: Approx. 54 - 66
Ω
PKIB5312E
LAN-414
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect TCM connector.
2.
Check resistance between TCM harness connector F103 termi-
nals 5 (L) and 6 (Y).
OK or NG
OK
>> Replace TCM.
NG
>> Repair harness between TCM and BCM.
Low Tire Pressure Warning Control Unit Circuit Inspection
AKS00CI1
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of low tire pressure warning control unit for damage, bend and loose con-
nection (control unit side and harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect low tire pressure warning control unit connector.
2.
Check resistance between low tire pressure warning control unit
harness connector M81 terminals 9 (L) and 21 (Y).
OK or NG
OK
>> Replace low tire pressure warning control unit.
NG
>> Repair harness between low tire pressure warning con-
trol unit and BCM.
BCM Circuit Inspection
AKS00CI2
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of BCM for damage, bend and loose connection (control module side and
harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
5 (L) - 6 (Y)
: Approx. 54 - 66
Ω
PKIB5313E
9 (L) - 21 (Y)
: Approx. 54 - 66
Ω
SKIA6885E
CAN SYSTEM (TYPE 10)
LAN-415
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect BCM connector.
2.
Check resistance between BCM harness connector M34 termi-
nals 39 (L) and 40 (Y).
OK or NG
OK
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
NG
>> Repair harness between BCM and harness connector
M82.
Display Control Unit Circuit Inspection
AKS00CI3
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of display control unit for damage, bend and loose connection (unit side
and harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect display control unit connector.
2.
Check resistance between display control unit harness connec-
tor M43 terminals 25 (L) and 26 (Y).
OK or NG
OK
>> Replace display control unit.
NG
>> Repair harness between display control unit and data
link connector.
Data Link Connector Circuit Inspection
AKS00CI4
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check data link connector and terminals for damage, bend and loose connection (connector side and har-
ness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
39 (L) - 40 (Y)
: Approx. 54 - 66
Ω
PKIB5314E
25 (L) - 26 (Y)
: Approx. 54 - 66
Ω
SKIA6884E
LAN-416
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR OPEN CIRCUIT
Check resistance between data link connector M24 terminals 6 (L)
and 14 (Y).
OK or NG
OK
NG
>> Repair harness between data link connector and unified
meter and A/C amp.
Unified Meter and A/C Amp. Circuit Inspection
AKS00CI5
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of unified meter and A/C amp. for damage, bend and loose connection
(meter side and harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect unified meter and A/C amp. connector.
2.
Check resistance between unified meter and A/C amp. harness
connector M49 terminals 1 (L) and 11 (Y).
OK or NG
OK
>> Replace unified meter and A/C amp.
NG
>> Repair harness between unified meter and A/C amp.
and data link connector.
Steering Angle Sensor Circuit Inspection
AKS00CI6
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of steering angle sensor for damage, bend and loose connection (sensor
side and harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
6 (L) - 14 (Y)
: Approx. 54 - 66
Ω
SKIA6868E
1 (L) - 11 (Y)
: Approx. 54 - 66
Ω
SKIA6871E
CAN SYSTEM (TYPE 10)
LAN-417
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect steering angle sensor connector.
2.
Check resistance between steering angle sensor harness con-
nector M33 terminals 4 (L) and 5 (Y).
OK or NG
OK
>> Replace steering angle sensor.
NG
>> Repair harness between steering angle sensor and data
link connector.
Driver Seat Control Unit Circuit Inspection
AKS00CI7
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check following terminals and connectors for damage, bend and loose connection (control unit side and
harness side).
–
Driver seat control unit connector
–
Harness connector B301
–
Harness connector B9
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect driver seat control unit connector.
2.
Check resistance between driver seat control unit harness con-
nector B303 terminals 3 (L/Y) and 19 (BR/W).
OK or NG
OK
>> Replace driver seat control unit.
NG
>> Repair harness between driver seat control unit and har-
ness connector B4.
AWD Control Unit Circuit Inspection
AKS00AHP
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of AWD control unit for damage, bend and loose connection (control unit
side and harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
4 (L) - 5 (Y)
: Approx. 54 - 66
Ω
SKIA6870E
3 (L/Y) - 19 (BR/W)
: Approx. 54 - 66
Ω
PKIB5315E
LAN-418
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect AWD control unit connector.
2.
Check resistance between AWD control unit harness connector
E111 terminals 8 (L) and 16 (Y).
OK or NG
OK
>> Replace AWD control unit.
NG
>> Repair harness between AWD control unit and IPDM E/
R.
ABS Actuator and Electric Unit (Control Unit) Circuit Inspection
AKS00CI8
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of ABS actuator and electric unit (control unit) for damage, bend and loose
connection (control unit side and harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect ABS actuator and electric unit (control unit) connector.
2.
Check resistance between ABS actuator and electric unit (con-
trol unit) harness connector E24 terminals 11 (L) and 15 (Y).
OK or NG
OK
>> Replace ABS actuator and electric unit (control unit).
NG
>> Repair harness between ABS actuator and electric unit
(control unit) and IPDM E/R.
IPDM E/R Circuit Inspection
AKS00CI9
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of IPDM E/R for damage, bend and loose connection (control module side
and harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
8 (L) - 16 (Y)
: Approx. 54 - 66
Ω
SKIA6889E
11 (L) - 15 (Y)
: Approx. 54 - 66
Ω
PKIB5316E
CAN SYSTEM (TYPE 10)
LAN-419
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check resistance between IPDM E/R harness connector E9 ter-
minals 48 (L) and 49 (Y).
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Repair harness between IPDM E/R and ABS actuator
and electric unit (control unit).
CAN Communication Circuit Inspection
AKS00CIA
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check following terminals and connectors for damage, bend and loose connection (control module side,
control unit side, unit side, meter side, sensor side and harness side).
–
ECM
–
Intelligent Key unit
–
TCM
–
Low tire pressure warning control unit
–
BCM
–
Display control unit
–
Unified meter and A/C amp.
–
Steering angle sensor
–
Driver seat control unit
–
AWD control unit
–
ABS actuator and electric unit (control unit)
–
IPDM E/R
–
Between ECM and IPDM E/R
–
Between ECM and TCM
–
Between ECM and driver seat control unit
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
48 (L) - 49 (Y)
: Approx. 108 - 132
Ω
PKIB5317E
LAN-420
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect following connectors.
–
ECM connector
–
Intelligent Key unit connector
–
Harness connector M82
–
Low tire pressure warning control unit connector
–
BCM connector
–
Display control unit connector
–
Unified meter and A/C amp. connector
–
Steering angle sensor connector
–
Harness connector M9
2.
Check continuity between data link connector M24 terminals 6
(L) and 14 (Y).
OK or NG
OK
>> GO TO 3.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between data link connector and ECM
●
Harness between data link connector and Intelligent
Key unit
●
Harness between data link connector and harness connector M82
●
Harness between data link connector and low tire pressure warning control unit
●
Harness between data link connector and BCM
●
Harness between data link connector and display control unit
●
Harness between data link connector and unified meter and A/C amp.
●
Harness between data link connector and steering angle sensor
●
Harness between data link connector and harness connector M9
6 (L) - 14 (Y)
: Continuity should not exist.
SKIA6868E
CAN SYSTEM (TYPE 10)
LAN-421
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
3.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between data link connector M24 terminals 6 (L),
14 (Y) and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between data link connector and ECM
●
Harness between data link connector and Intelligent
Key unit
●
Harness between data link connector and harness connector M82
●
Harness between data link connector and low tire pressure warning control unit
●
Harness between data link connector and BCM
●
Harness between data link connector and display control unit
●
Harness between data link connector and unified meter and A/C amp.
●
Harness between data link connector and steering angle sensor
●
Harness between data link connector and harness connector M9
4.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect TCM connector.
2.
Check continuity between TCM harness connector F103 termi-
nals 5 (L) and 6 (Y).
OK or NG
OK
>> GO TO 5.
NG
>> Repair harness between TCM and harness connector
F102.
5.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between TCM harness connector F103 terminals 5
(L), 6 (Y) and ground.
OK or NG
OK
>> GO TO 6.
NG
>> Repair harness between TCM and harness connector
F102.
6 (L) - Ground
: Continuity should not exist.
14 (Y) - Ground
: Continuity should not exist.
PKIB5318E
5 (L) - 6 (Y)
: Continuity should not exist.
PKIB5313E
5 (L) - Ground
: Continuity should not exist.
6 (Y) - Ground
: Continuity should not exist.
PKIB5319E
LAN-422
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
6.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect harness connector B4 and harness connector B9.
2.
Check continuity between harness connector B4 terminals 4 (L)
and 10 (Y).
OK or NG
OK
>> GO TO 7.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between harness connector B4 and harness
connector B2
●
Harness between harness connector B4 and harness
connector B9
7.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between harness connector B4 terminals 4 (L), 10
(Y) and ground.
OK or NG
OK
>> GO TO 8.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between harness connector B4 and harness
connector B2
●
Harness between harness connector B4 and harness connector B9
8.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect driver seat control unit connector.
2.
Check continuity between driver seat control unit harness con-
nector B303 terminals 3 (L/Y) and 19 (BR/W).
OK or NG
OK
>> GO TO 9.
NG
>> Repair harness between driver seat control unit and har-
ness connector B301.
4 (L) - 10 (Y)
: Continuity should not exist.
PKIB5320E
4 (L) - Ground
: Continuity should not exist.
10 (Y) - Ground
: Continuity should not exist.
PKIB5321E
3 (L/Y) - 19 (BR/W)
: Continuity should not exist.
PKIB5315E
CAN SYSTEM (TYPE 10)
LAN-423
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
9.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between driver seat control unit harness connector
B303 terminals 3 (L/Y), 19 (BR/W) and ground.
OK or NG
OK
>> GO TO 10.
NG
>> Repair harness between driver seat control unit and har-
ness connector B301.
10.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect following connectors.
–
AWD control unit connector
–
ABS actuator and electric unit (control unit) connector
–
IPDM E/R connector
2.
Check continuity between IPDM E/R harness connector E9 ter-
minals 48 (L) and 49 (Y).
OK or NG
OK
>> GO TO 11.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between IPDM E/R and AWD control unit
●
Harness between IPDM E/R and ABS actuator and
electric unit (control unit)
●
Harness between IPDM E/R and harness connector E105
11.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between IPDM E/R harness connector E9 termi-
nals 48 (L), 49 (Y) and ground.
OK or NG
OK
>> GO TO 12.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between IPDM E/R and AWD control unit
●
Harness between IPDM E/R and ABS actuator and
electric unit (control unit)
●
Harness between IPDM E/R and harness connector E105
3 (L/Y) - Ground
: Continuity should not exist.
19 (BR/W) - Ground
: Continuity should not exist.
PKIB5322E
48 (L) - 49 (Y)
: Continuity should not exist.
PKIB5317E
48 (L) - Ground
: Continuity should not exist.
49 (Y) - Ground
: Continuity should not exist.
PKIB5323E
LAN-424
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
12.
CHECK ECM AND IPDM E/R INTERNAL CIRCUIT
1.
Remove ECM and IPDM E/R from vehicle.
2.
Check resistance between ECM terminals 94 and 86.
3.
Check resistance between IPDM E/R terminals 48 and 49.
OK or NG
OK
>> GO TO 13.
NG
>> Replace ECM and/or IPDM E/R.
13.
CHECK SYMPTOM
1.
Fill in described symptoms on the column “Symptom” in the check sheet.
2.
Connect all the connectors, and then make sure that the symptom is reproduced.
OK or NG
OK
>> GO TO 14.
NG
>> Refer to
LAN-17, "Example of Filling in Check Sheet When Initial Conditions Are Not Reproduced"
.
14.
CHECK UNIT REPRODUCIBILITY
Perform the following procedure for each unit, and then perform reproducibility test.
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect the unit connector.
4.
Connect the battery cable to the negative terminal.
5.
Make sure that the symptom filled in the “Symptom” of the check sheet is reproduced. (Do not confuse it
with the symptom related to removed unit.)
6.
Make sure that the same symptom is reproduce.
–
Intelligent Key unit
–
TCM
–
Low tire pressure warning control unit
–
BCM
–
Display control unit
–
Unified meter and A/C amp.
–
Steering angle sensor
–
Driver seat control unit
–
AWD control unit
–
ABS actuator and electric unit (control unit)
–
ECM
–
IPDM E/R
Check results
Reproduced>>Install removed unit, and then check the other unit.
Not reproduced>>Replace removed unit.
94 - 86
: Approx. 108 – 132
Ω
48 - 49
: Approx. 108 – 132
Ω
LKIA0037E
CAN SYSTEM (TYPE 10)
LAN-425
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
IPDM E/R Ignition Relay Circuit Inspection
AKS00CIB
Check the following. If no malfunction is found, replace the IPDM E/R.
●
IPDM E/R power supply circuit. Refer to
PG-27, "IPDM E/R Power/Ground Circuit Inspection"
●
Ignition power supply circuit. Refer to
PG-10, "IGNITION POWER SUPPLY - IGNITION SW. IN “ON”
.
LAN-426
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION
LT
A
B
LT
Revision: 2005 August
2005 Murano
LIGHTING SYSTEM
PRECAUTIONS . . . . . . . . . . . . . . .. 5
HEADLAMP - XENON TYPE - . . . . . . . . ... 6
Component Parts and Harness Connector Location
System Description . . . . . . . . . . . . .. 6
EXTERIOR LAMP BATTERY SAVER CONTROL
CHECK POWER SUPPLY AND GROUND CIR-
CUIT . . . . . . . . . . . . . . . . . 16
CONSULT-II Functions (BCM) . . . . . . . ... 17
CONSULT-II Functions (IPDM E/R) . . . . . ... 20
Bulb Replacement . . . . . . . . . . . . .. 36
Removal and Installation . . . . . . . . . . 37
REMOVAL . . . . . . . . . . . . . . ... 37
INSTALLATION . . . . . . . . . . . . ... 37
Disassembly and Assembly . . . . . . . . . 37
DISASSEMBLY . . . . . . . . . . . . ... 37
ASSEMBLY . . . . . . . . . . . . . . . 38
HEADLAMP -CONVENTIONAL TYPE- . . . . . 39
Component Parts and Harness Connector Location
LT-2
Revision: 2005 August
2005 Murano
CHECK POWER SUPPLY AND GROUND CIR-
CUIT . . . . . . . . . . . . . . . . . 49
CONSULT-II Functions (BCM) . . . . . . . . 50
CONSULT-II Functions (IPDM E/R) . . . . . . 53
Bulb Replacement . . . . . . . . . . . . .. 66
Removal and Installation . . . . . . . . . . 67
REMOVAL . . . . . . . . . . . . . . ... 67
INSTALLATION . . . . . . . . . . . . . 67
Disassembly and Assembly . . . . . . . . . 68
DISASSEMBLY . . . . . . . . . . . . ... 68
ASSEMBLY . . . . . . . . . . . . . . . 68
DAYTIME LIGHT SYSTEM . . . . . . . . . ... 69
CONSULT-II Functions (BCM) . . . . . . . . 80
CONSULT-II Functions (IPDM E/R) . . . . . . 83
AUTO LIGHT SYSTEM . . . . . . . . . . . .88
Component Parts and Harness Connector Location ...88
System Description . . . . . . . . . . . . .88
CONSULT-II Functions (BCM) . . . . . . . . 98
CONSULT-II Functions (IPDM E/R) . . . . . ..101
REMOVAL . . . . . . . . . . . . . . ..106
INSTALLATION . . . . . . . . . . . . ..106
HEADLAMP AIMING CONTROL . . . . . . . 107
Wiring Diagram — H/AIM — . . . . . . . . .107
Removal and Installation . . . . . . . . . ...109
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст