Nissan Murano Z50 (2005 year). Manual — part 174
CAN SYSTEM (TYPE 10)
LAN-397
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
Case 6
Check Intelligent Key unit circuit. Refer to
LAN-413, "Intelligent Key Unit Circuit Inspection"
.
PKIB4891E
PKIB4679E
LAN-398
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
Case 7
Check TCM circuit. Refer to
LAN-413, "TCM Circuit Inspection"
PKIB4892E
PKIB4680E
CAN SYSTEM (TYPE 10)
LAN-399
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
Case 8
Check low tire pressure warning control unit circuit. Refer to
LAN-414, "Low Tire Pressure Warning Control
.
PKIB4893E
PKIB4681E
LAN-400
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
Case 9
Check BCM circuit. Refer to
LAN-414, "BCM Circuit Inspection"
PKIB4894E
PKIB4682E
CAN SYSTEM (TYPE 10)
LAN-401
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
Case 10
Check display control unit circuit. Refer to
LAN-415, "Display Control Unit Circuit Inspection"
PKIB4895E
PKIB4683E
LAN-402
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
Case 11
Check data link connector circuit. Refer to
LAN-415, "Data Link Connector Circuit Inspection"
PKIB4896E
PKIB4684E
CAN SYSTEM (TYPE 10)
LAN-403
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
Case 12
Check unified meter and A/C amp. circuit. Refer to
LAN-416, "Unified Meter and A/C Amp. Circuit Inspection"
PKIB4897E
PKIB4685E
LAN-404
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
Case 13
Check steering angle sensor circuit. Refer to
LAN-416, "Steering Angle Sensor Circuit Inspection"
PKIB4898E
PKIB4686E
CAN SYSTEM (TYPE 10)
LAN-405
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
Case 14
Check driver seat control unit circuit. Refer to
LAN-417, "Driver Seat Control Unit Circuit Inspection"
PKIB4899E
PKIB4687E
LAN-406
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
Case 15
Check AWD control unit circuit. Refer to
LAN-417, "AWD Control Unit Circuit Inspection"
.
PKIB4900E
PKIB4688E
CAN SYSTEM (TYPE 10)
LAN-407
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
Case 16
Check ABS actuator and electric unit (control unit) circuit. Refer to
LAN-418, "ABS Actuator and Electric Unit
(Control Unit) Circuit Inspection"
.
PKIB4901E
PKIB4689E
LAN-408
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
Case 17
Check IPDM E/R circuit. Refer to
LAN-418, "IPDM E/R Circuit Inspection"
PKIB4902E
PKIB4690E
CAN SYSTEM (TYPE 10)
LAN-409
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
Case 18
Check CAN communication circuit. Refer to
LAN-419, "CAN Communication Circuit Inspection"
Case 19
Check IPDM E/R ignition relay circuit continuously sticks “OFF”. Refer to
LAN-425, "IPDM E/R Ignition Relay
PKIB4903E
PKIC6351E
LAN-410
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
Case 20
Check IPDM E/R ignition relay circuit continuously sticks “ON”. Refer to
LAN-425, "IPDM E/R Ignition Relay
Inspection Between TCM and Data Link Connector Circuit
AKS00CHV
1.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect ECM connector and harness connector M82.
4.
Check continuity between harness connector M82 terminals 8
(L), 9 (Y) and data link connector M24 terminals 6 (L), 14 (Y).
OK or NG
OK
>> Connect all the connectors and diagnose again. Refer to
LAN-7, "TROUBLE DIAGNOSES WORK FLOW"
NG
>> Repair harness.
Inspection Between Data Link Connector and Driver Seat Control Unit Circuit
AKS00CHW
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check following terminals and connectors for damage, bend and loose connection (connector side and
harness side).
–
Harness connector M9
–
Harness connector B2
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
PKIC6352E
8 (L) - 6 (L)
: Continuity should exist.
9 (Y) - 14 (Y)
: Continuity should exist.
PKIB5306E
CAN SYSTEM (TYPE 10)
LAN-411
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect harness connector M9.
2.
Check continuity between data link connector M24 terminals 6
(L), 14 (Y) and harness connector M9 terminals 1 (L), 13 (Y).
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness.
3.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect harness connector B4.
2.
Check continuity between harness connector B2 terminals 1 (L),
13 (Y) and harness connector B4 terminals 4 (L), 10 (Y).
OK or NG
OK
>> Connect all the connectors and diagnose again. Refer to
LAN-7, "TROUBLE DIAGNOSES WORK FLOW"
NG
>> Repair harness.
Inspection Between Driver Seat Control Unit and AWD Control Unit Circuit
AKS00CHX
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check following terminals and connectors for damage, bend and loose connection (connector side and
harness side).
–
Harness connector B4
–
Harness connector E105
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect harness connector B4.
2.
Check continuity between harness connector B2 terminals 1 (L),
13 (Y) and harness connector B4 terminals 4 (L), 10 (Y).
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness.
6 (L) - 1 (L)
: Continuity should exist.
14 (Y) - 13 (Y)
: Continuity should exist.
PKIB5307E
1 (L) - 4 (L)
: Continuity should exist.
13 (Y) - 10 (Y)
: Continuity should exist.
PKIB5308E
1 (L) - 4 (L)
: Continuity should exist.
13 (Y) - 10 (Y)
: Continuity should exist.
PKIB5308E
LAN-412
[CAN]
CAN SYSTEM (TYPE 10)
Revision: 2005 August
2005 Murano
3.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect AWD control unit connector.
2.
Check continuity between harness connector E105 terminals 4
(L), 10 (Y) and AWD control unit harness connector E111 termi-
nals 8 (L), 16 (Y).
OK or NG
OK
>> Connect all the connectors and diagnose again. Refer to
LAN-7, "TROUBLE DIAGNOSES WORK FLOW"
NG
>> Repair harness.
Inspection Between AWD Control Unit and ABS Actuator and Electric Unit
(Control Unit) Circuit
AKS00CIC
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect following connectors.
–
ECM
–
AWD control unit
–
ABS actuator and electric unit (control unit)
4.
Check continuity between AWD control unit harness connector
E111 terminals 8 (L), 16 (Y) and ABS actuator and electric unit
(control unit) harness connector E24 terminals 11 (L), 15 (Y).
OK or NG
OK
>> Connect all the connectors and diagnose again. Refer to
LAN-7, "TROUBLE DIAGNOSES WORK FLOW"
NG
>> Repair harness.
ECM Circuit Inspection
AKS00CHY
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check terminals and connector of ECM for damage, bend and loose connection (control module side and
harness side).
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
4 (L) - 8 (L)
: Continuity should exist.
10 (Y) - 16 (Y)
: Continuity should exist.
PKIB5310E
8 (L) - 11 (L)
: Continuity should exist.
16 (Y) - 15 (Y)
: Continuity should exist.
PKIB5311E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст