Nissan Murano Z50 (2005 year). Manual — part 131
ENGINE ASSEMBLY
EM-109
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
Preparation
1.
Release fuel pressure. Refer to
EC-92, "FUEL PRESSURE RELEASE"
2.
Drain engine coolant. Refer to
CO-9, "Changing Engine Coolant"
.
CAUTION:
●
Perform this step when the engine is cold.
●
Do not spill engine coolant on drive belts.
3.
Remove the following parts:
●
Engine cover; Refer to
EM-18, "INTAKE MANIFOLD COLLECTOR"
●
●
Front road wheel and tires
●
Undercover and splash guards (RH and LH)
●
Air duct (inlet), air cleaner case (upper) with mass air flow sensor and air duct assembly; Refer to
16, "AIR CLEANER AND AIR DUCT"
.
●
Battery, battery tray and battery tray bracket; Refer to
●
●
Radiator, reservoir tank of radiator, and system hoses. Refer to
●
Front wiper arm; Refer to
WW-4, "FRONT WIPER AND WASHER SYSTEM"
.
●
Extension cowl top panel (lower and upper); Refer to
4.
Disconnect engine room harness at the ECM side.
CAUTION:
To keep clean harness connector and avoid damage and foreign materials, cover them completely
with plastic bags or something similar.
Engine Room
1.
Disconnect heater hoses. Refer to
CO-29, "WATER OUTLET AND WATER PIPING"
●
Install plug to avoid leakage of engine coolant.
2.
EM-18, "INTAKE MANIFOLD COLLECTOR"
.
3.
Disconnect fuel feed hose (with fuel damper) quick connector at centralized under-floor piping side. Refer
to
EM-41, "FUEL INJECTOR AND FUEL TUBE"
●
Install plug to avoid leakage of fuel.
4.
Disconnect transaxle shift control cable at transaxle side. Refer to
5.
Disconnect brake booster vacuum hose at engine side. Refer to
EM-18, "INTAKE MANIFOLD COLLEC-
.
6.
7.
Remove A/C compressor with piping connected, and temporarily secure it to aside. Refer to
.
8.
Disconnect suction hoses of power steering oil pump at reservoir tank side. Refer to
●
Install plug to avoid leakage of power steering fluid.
Vehicle Underbody
1.
Remove front drive shafts (right and left sides). Refer to
2.
Remove exhaust front tube. Refer to
.
3.
Disconnect steering lower joint at power steering gear assembly side, and release steering lower shaft.
Refer to
PS-15, "POWER STEERING GEAR AND LINKAGE"
4.
Disconnect front stabilizer connecting rod. Refer to
5.
Remove strut assembly and steering knuckle fixing nuts and bolts. Refer to
6.
Remove front brake cylinder body with piping connected, and temporarily secure it to aside for vehicle
side. Refer to
7.
EM-110
ENGINE ASSEMBLY
Revision: 2005 August
2005 Murano
8.
Disconnect power steering piping at a point between vehicle and engine. Refer to
.
●
Install plug to avoid leakage of power steering fluid.
9.
Remove rear plate cover from oil pan (upper). Then remove bolts fixing drive plate to torque converter.
Refer to
EM-29, "OIL PAN AND OIL STRAINER"
10. Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side. Refer to
.
11. Remove crankshaft position sensor (POS).
CAUTION:
●
Handle carefully to avoid dropping and shocks.
●
Do not disassemble.
●
Do not allow metal powder to adhere to magnetic part at sensor tip.
●
Do not place sensors in a location where they are exposed to magnetism.
Removal Work
1.
Use a manual lift table caddy (commercial service tool) or equiv-
alently rigid tool such as a transmission jack. Securely support
bottom of front suspension member.
CAUTION:
Put a piece of wood or something similar as the supporting
surface, secure a completely stable condition.
2.
Remove RH engine mounting insulator and RH engine mounting bracket.
3.
Remove mounting bolt between transverse link and front suspension member with power tool.
4.
Remove front suspension member mounting nuts and bolts. Refer to
5.
Carefully lower jack, or raise lift to remove the engine, the transaxle and transfer (AWD models) assembly
and front suspension member. When performing work, observe the following caution:
CAUTION:
●
Confirm there is no interference with the vehicle.
●
Make sure all connection points have been disconnected.
●
Keep in mind the center of vehicle gravity changes. If necessary, use jack(s) to support the vehi-
cle at rear jacking point(s) to prevent it from falling it off the lift.
PBIC1190E
ENGINE ASSEMBLY
EM-111
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
Separation Work
1.
Install engine slingers into front of cylinder head (right bank) and
rear of cylinder head (left bank).
2.
Remove power steering oil pump, power steering piping and power steering bracket from engine, tran-
saxle and transfer (AWD models) assembly. Refer to
3.
Remove starter motor. Refer to
.
4.
Disconnect harness connector of front engine mounting insulator and rear engine mounting insulator
(AWD models).
5.
Lift with hoist and separate engine, transaxle and transfer (AWD models) assembly from front suspension
member.
CAUTION:
●
Before and during this lifting, always check if any harnesses are left connected.
●
Avoid damage to and oil/grease smearing or spills onto engine mounting insulator.
6.
Remove each engine mounting insulator and each engine mounting bracket from engine, transaxle and
front suspension member.
7.
Separate engine, transaxle and transfer (AWD models) assembly. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
●
Do not allow engine mounting insulator to be damage and careful no oil gets on it.
●
For a path with a specified installation orientation, refer to component figure in
.
●
Make sure all mounting insulators are seated properly, then tighten mounting nuts and bolts.
INSPECTION AFTER INSTALLATION
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.
●
Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-10, "RECOMMENDED FLUIDS AND LUBRICANTS"
●
Use procedure below to check for fuel leakage.
–
Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–
Start engine. With engine speed increased, check again for fuel leakage at connection points.
●
Run engine to check for unusual noise and vibration.
PBIC2483E
EM-112
ENGINE ASSEMBLY
Revision: 2005 August
2005 Murano
●
Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.
●
Bleed air from lines and hoses of applicable lines, such as in cooling system.
●
After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
* Transmission/transaxle/CVT fluid. power steering fluid, brake fluid, etc.
Item
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
CYLINDER BLOCK
EM-113
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
CYLINDER BLOCK
PFP:11010
Disassembly and Assembly
ABS00A3T
PBIC2683E
EM-114
CYLINDER BLOCK
Revision: 2005 August
2005 Murano
DISASSEMBLY
1.
Remove engine assembly from the vehicle, and separate front suspension member, transaxle and trans-
fer (AWD models) assembly from engine. Refer to
.
2.
Remove exhaust manifolds (right and left banks). Refer to
EM-25, "EXHAUST MANIFOLD AND THREE
3.
Remove oil cooler, water pipes and water hoses. Refer to
.
●
When removing water drain plug, engine coolant remaining in the engine is drained. Use tray to collect
it.
1.
Reinforcement plate
2.
Drive plate
3.
Rear oil seal retainer
4.
Knock sensor
5.
Cylinder block
6.
Thrust bearing (upper)
7.
Main bearing (upper)
8.
Crankshaft
9.
Crankshaft key
10. Thrust bearing (lower)
11. Main bearing (lower)
12. Main bearing cap
13. Main bearing cap bolt
14. Main bearing beam
15. Connecting rod bolt
16. Connecting rod bearing cap
17. Connecting rod bearing
18. Connecting rod
19. Snap ring
20. Piston pin
21. Piston
22. Oil ring
23. Second ring
24. Top ring
25. Pilot converter
26. Oil jet
1.
Cylinder block
2.
Gasket
3.
Cylinder block heater
4.
Connector protector cap
PBIC2684E
CYLINDER BLOCK
EM-115
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
4.
Install engine sub-attachment with engine stand shaft [SST] to
right side of cylinder block.
●
Use a spacer to engine front side.
5.
Lift engine, and mount it onto engine stand [SST].
●
A widely use engine stand can be used.
CAUTION:
Use an engine stand that has a load capacity [approxi-
mately 220 kg (441 lb) or more] large enough for support-
ing the engine weight.
NOTE:
This example is an engine stand for holding at transaxle
mounting side with drive plate removed.
6.
.
PBIC0920E
PBIC2685E
PBIC0085E
EM-116
CYLINDER BLOCK
Revision: 2005 August
2005 Murano
7.
Drain engine coolant by removing water drain plug “A”, “B” and
connector bolt “D” from cylinder block as shown in the figure.
NOTE:
For Canada, “A” in the figure is not water drain plug but block
heater.
8.
Remove drive plate. Fix crankshaft pulley with the pulley holder [SST: KV10109300 (
—
)], and remove
mounting bolts.
●
Loosen mounting bolts in diagonal order.
CAUTION:
●
Do not disassemble drive plate.
●
Never place drive plate with signal plate facing down.
●
When handling signal plate, take care not to damage or
scratch it.
●
Handle signal plate in a manner that prevents it from
becoming magnetized.
9.
Remove the following parts:
●
Intake manifold collectors (upper and lower); Refer to
EM-18, "INTAKE MANIFOLD COLLECTOR"
.
●
Intake manifold; Refer to
●
Oil pans (lower and upper); Refer to
EM-29, "OIL PAN AND OIL STRAINER"
●
Front and rear timing chain case; Refer to
●
Cylinder head; Refer to
.
10. Remove knock sensor.
CAUTION:
Carefully handle sensor avoiding shocks.
PBIC2487E
SEM760G
CYLINDER BLOCK
EM-117
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
11. Remove pilot converter using the pilot bushing puller [SST] as
necessary.
12. Remove rear oil seal retainer.
●
Remove by inserting screwdriver between main bearing cap and rear oil seal retainer.
CAUTION:
If rear oil seal retainer is removed, replace it with new one.
NOTE:
Regard both rear oil seal and retainer as an assembly.
13. Remove piston and connecting rod assembly with the following procedure:
●
Before removing piston and connecting rod assembly, check the connecting rod side clearance. Refer
to
EM-131, "CONNECTING ROD SIDE CLEARANCE"
.
CAUTION:
Be careful not to drop connecting rod bearing, and to scratch the surface.
a.
Position crankshaft pin corresponding to connecting rod to be removed onto the bottom dead center.
b.
Remove connecting rod bearing cap.
c.
Using a hammer handle or similar tool, push piston and connect-
ing rod assembly out to the cylinder head side.
CAUTION:
Be careful not to damage the cylinder wall and crankshaft
pin, resulting from an interference of the connecting rod big
end.
14. Remove connecting rod bearings from connecting rod and connecting rod bearing cap.
CAUTION:
●
Be careful not to drop connecting rod bearing, and to scratch the surface.
●
Identify installation positions, and store them without mixing them up.
15. Remove piston rings form piston.
●
Before removing piston rings, check the piston ring side clearance. Refer to
●
Use a piston ring expander (commercial service tool).
CAUTION:
●
When removing piston rings, be careful not to damage
piston.
●
Be careful not to damage piston rings by expanding them
excessively.
SEM005G
EMQ0191D
PBIC0087E
EM-118
CYLINDER BLOCK
Revision: 2005 August
2005 Murano
16. Remove piston from connecting rod as follows:
a.
Using a snap ring pliers, remove snap rings.
b.
Heat piston to 60 to 70
°
C (140 to 158
°
F) with an industrial use
drier or equivalent.
c.
Push out piston pin with stick of outer diameter approximately 20
mm (0.79 in).
17. Remove main bearing cap bolts.
NOTE:
Use TORX socket (size E14).
●
Before loosening main bearing cap bolts, measure the crankshaft end play. Refer to
●
Loosen main bearing cap bolts in the reverse order shown in
the figure in several different steps.
PBIC1638E
PBIC1639E
PBIC0262E
PBIC1800E
CYLINDER BLOCK
EM-119
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
18. Remove main bearing beam.
19. Remove main bearing caps.
CAUTION:
Be careful not to drop main bearing, and to scratch the sur-
face.
●
Using main bearing cap bolts, remove main bearing cap while
shaking it back-and-forth.
20. Remove crankshaft.
21. Remove main bearings and thrust bearings from cylinder block and main bearing caps.
CAUTION:
●
Be careful not to drop main bearing, and to scratch the surface.
●
Identify installation positions, and store them without mixing them up.
22. Remove oil jet.
ASSEMBLY
1.
Fully air-blow engine coolant and engine oil passages in cylinder block, cylinder bore and crankcase to
remove any foreign material.
CAUTION:
Use a goggles to protect your eye.
2.
Install each plug to cylinder block as shown in the figure.
●
Apply sealant to the thread of water drain plug “A”.
Use Anaerobic Liquid Gasket or equivalent. Refer to
47, "RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS"
NOTE:
For Canada, “A” in the figure is not water drain plug but block
heater. Refer to
EM-113, "Disassembly and Assembly"
.
●
Apply sealant to the thread of water drain plug “B” and con-
nector bolt “D”.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS"
●
Apply sealant to the thread of plug “C”.
Use Genuine High Strength Locking Sealant or equiva-
lent. Refer to
GI-47, "RECOMMENDED CHEMICAL PROD-
.
●
Replace washers with new one.
PBIC0881E
EMQ0195D
PBIC2487E
EM-120
CYLINDER BLOCK
Revision: 2005 August
2005 Murano
●
Tighten each plug and connector bolt as specified below.
3.
Install oil jet.
●
Insert oil jet dowel pin into cylinder block dowel pin hole, and
tighten mounting bolts.
4.
Install main bearings and thrust bearings as follow:
CAUTION:
Be careful not to drop main bearing, and to scratch the surface.
a.
Remove dust, dirt, and engine oil on bearing mating surfaces of cylinder block and main bearing caps.
b.
Install thrust bearings to the both sides of the No. 3 journal hous-
ing on cylinder block and main bearing cap.
●
Install thrust bearings with the oil groove facing crankshaft
arm (outside).
●
Install thrust bearing with a projection on one end on cylinder
block, and thrust bearing with a projection at center on main
bearing cap. Align each projection with mating notch.
c.
Install main bearings paying attention to the direction.
●
Main bearing with oil hole and groove goes on cylinder block.
The one without them goes on main bearing cap.
●
Before installing main bearings, apply engine oil to the bear-
ing surface (inside). Do not apply engine oil to the back sur-
face, but thoroughly clean it.
●
When installing, align main bearing stopper protrusion to cut-
out of cylinder block and main bearing caps.
●
Ensure the oil holes on cylinder block and those on the corre-
sponding bearing are aligned.
5.
Install crankshaft to cylinder block.
●
While turning crankshaft by hand, check that it turns smoothly.
6.
Install main bearing caps.
Part
Washer
Tightening torque
A
Yes
62.0 N·m (6.3 kg-m, 46 ft-lb)
B
No
9.8 N·m (1.0 kg-m, 87 in-lb)
C
Yes
62.0 N·m (6.3 kg-m, 46 ft-lb)
D
No
39.2 N·m (4.0 kg-m, 29 ft-lb)
PBIC0898E
PBIC0807E
PBIC2489E
CYLINDER BLOCK
EM-121
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
●
Main bearing caps are identified by identification mark cast on
them. For installation, face front mark to front side.
NOTE:
Main bearing cap cannot be replaced as a single part, because it
is machined together with cylinder block.
7.
Install main bearing beam.
●
Install main bearing beam with front mark facing downward (oil pan side).
●
Install main bearing beam with front mark facing front of the
engine.
8.
Install main bearing cap bolts in numerical order as shown in the
figure as follows:
a.
Inspect the outer diameter of main bearing cap bolt. Refer to
EM-139, "MAIN BEARING CAP BOLT OUTER DIAMETER"
b.
Apply new engine oil to threads and seat surfaces of main bear-
ing cap bolts.
c.
Tighten main bearing cap bolts in several different steps.
d.
Turn all main bearing cap bolts 90 degrees clockwise (Angle
tightening).
CAUTION:
Use the angle wrench [SST: KV10112100 (BT8653-A)] to
check tightening angle. Do not make judgment by visual
inspection.
●
After installing main bearing cap bolts, make sure that crank-
shaft can be rotated smoothly by hand.
●
Check the crankshaft end play. Refer to
.
9.
Install piston to connecting rod as follows:
a.
Using snap ring pliers, install new snap ring to the groove of piston rear side.
●
Insert it fully into groove to install.
b.
Install piston to connecting rod.
●
Using an industrial drier or similar tool, heat piston until piston pin can be pushed in by hand without
excess force [approx. 60 to 70
°
C (140 to 158
°
F)]. From the front to the rear, insert piston pin into piston
and connecting rod.
SEM456G
PBIC0881E
: 35.3 N·m (3.6 kg-m, 26 ft-lb)
PBIC1800E
PBIC0921E
EM-122
CYLINDER BLOCK
Revision: 2005 August
2005 Murano
●
Assemble so that the front mark on the piston crown and the
cylinder number on connecting rod are positioned as shown in
the figure.
c.
Install new snap ring to the groove of the piston front side.
●
Insert it fully into groove to install.
●
After installing, make sure that connecting rod moves
smoothly.
10. Using a piston ring expander (commercial service tool), install
piston rings.
CAUTION:
●
When installing piston rings, be careful not to damage
piston.
●
Be careful not to damage piston rings by expending them
excessively.
●
If there is stamped mark on ring, mount it with marked side
up.
NOTE:
If there is no stamp on ring, no specific orientation is required
for installation.
●
Position each ring with the gap as shown in the figure refer-
ring to the piston front mark.
●
Check the piston rings side clearance. Refer to
EM-132, "PISTON RING SIDE CLEARANCE"
11. Install connecting rod bearings to connecting rod and connecting rod bearing cap.
CAUTION:
Be careful not to drop connecting rod bearing, and to scratch the surface.
●
Before installing connecting rod bearings, apply engine oil to the bearing surface (inside). Do not apply
engine oil to the back surface, but thoroughly clean it.
SEM838F
PBIC0087E
Stamped mark:
Top ring
: —
Second ring
: R
SEM757G
PBIC0808E
CYLINDER BLOCK
EM-123
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
●
When installing, align connecting rod bearing stopper protru-
sion with cutout of connecting rod and connecting rod bearing
cap to install.
●
Ensure the oil hole on connecting rod and that on the corre-
sponding bearing are aligned.
12. Install piston and connecting rod assembly to crankshaft.
●
Position crankshaft pin corresponding to connecting rod to be installed onto the bottom dead center.
●
Apply engine oil sufficiently to the cylinder bore, piston and crankshaft pin journal.
●
Match the cylinder position with the cylinder number on connecting rod to install.
●
Be sure that front mark on piston crown is facing front of engine.
●
Using a piston ring compressor [SST] or suitable tool, install
piston with the front mark on the piston crown facing the front
of the engine.
CAUTION:
Be careful not to damage the cylinder wall and crankshaft
pin, resulting from an interference of the connecting rod big
end.
13. Install connecting rod bearing cap.
●
Match the stamped cylinder number marks on connecting rod
with those on connecting rod bearing cap to install.
●
Be sure that front mark on connecting rod bearing cap is fac-
ing front of the engine.
14. Tighten connecting rod bolt as follows:
a.
Inspect the outer diameter of connecting rod bolt. Refer to
EM-140, "CONNECTING ROD BOLT OUTER
b.
Apply engine oil to the threads and seats of connecting rod bolts.
c.
Tighten connecting rod bolts.
PBIC2067E
SEM620
PBIC0809E
: 19.6 N·m (2.0 kg-m, 14 ft-lb)
EM-124
CYLINDER BLOCK
Revision: 2005 August
2005 Murano
d.
Then tighten all connecting rod bolts 90 degrees clockwise
(Angle tightening).
CAUTION:
Always use the angle wrench [SST: KV10112100 (BT8653-
A)]. Avoid tightening based on visual check alone.
●
After tightening connecting rod bolts, make sure that crank-
shaft rotates smoothly.
●
Check the connecting rod side clearance. Refer to
"CONNECTING ROD SIDE CLEARANCE"
15. Install new rear oil seal retainer to cylinder block.
●
Apply new engine oil to both oil seal lip and dust seal lip.
●
Apply a continuous bead of liquid gasket with the tube presser
[SST: WS39930000 (
—
)] to rear oil seal retainer as
shown in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS"
.
CAUTION:
●
Replace with a new parts.
●
Attaching should be done within 5 minutes after coating.
●
Make sure the garter spring is in position and seal lips
not inverted.
NOTE:
Regard both rear oil seal and retainer as an assembly.
16. Install pilot converter.
●
With drift [outer diameter: approx. 33 mm (1.30 in)], press-fit
as far as it will go.
●
Press-fit pilot converter with its chamfer facing crankshaft as
shown in the figure.
SEM953E
PBIC2661E
PBIC0899E
SEM537E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст