Nissan Murano Z50 (2005 year). Manual — part 142
GW-14
BACK DOOR WINDOW GLASS
Revision: 2005 August
2005 Murano
●
Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
●
Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
●
While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger room air pressure when a door is closed.
●
Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
●
Keep heat and open flames away as primers and adhesive are flammable.
●
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
●
Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
●
Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the back door window glass in case of an accident.
CAUTION:
●
Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
●
Do not leave primers or adhesive cartridge unattended with their caps open or off.
●
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidity. The curing time will
increase under lower temperature and lower humidity.
PIIB0908E
SIDE WINDOW GLASS
GW-15
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2005 August
2005 Murano
SIDE WINDOW GLASS
PFP:83300
Removal and Installation
AIS002H9
REMOVAL
1.
Remove the luggage side finisher upper. Refer to
2.
Remove the headlining. Refer to
.
3.
Apply protective tape around the side window to protect the painted surface from damage.
4.
Remove the side window glass using piano wire or power cutting tool and an inflatable pump bag.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
●
Be careful not to scratch the glass when removing.
●
Do not set or stand the glass on its edge. Small chips may develop into cracks.
PIIA3793E
1.
Side window glass molding (Upper)
2.
Side window glass
3.
Clip
4.
Side window glass molding (Lower)
5.
Bond
6.
Body side outer panel
GW-16
SIDE WINDOW GLASS
Revision: 2005 August
2005 Murano
INSTALLATION
●
Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
●
While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger room air pressure when a door is closed.
●
The molding must be installed securely so that it is in position and leaves no gap.
●
Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
●
Keep heat and open flames away as primers and adhesive are flammable.
●
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
●
Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
●
Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the side window in case of an accident.
CAUTION:
●
Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
●
Do not leave primers or adhesive cartridge unattended with their caps open or off.
●
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidity. The curing time will
increase under lower temperature and lower humidity.
Repairing Water Leaks
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the side window area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
POWER WINDOW SYSTEM
GW-17
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2005 August
2005 Murano
POWER WINDOW SYSTEM
PFP:25401
Component Parts and Harness Connector Location
AIS002CN
PIIB4177E
GW-18
POWER WINDOW SYSTEM
Revision: 2005 August
2005 Murano
System Description
AIS002CO
Power is supplied at all time
●
from 50A fusible link (letter F , located in the fuse and fusible link box)
●
to BCM terminal 55
●
through 10A fuse [No.18, located in the fuse block (J/B)]
●
to BCM terminal 42
●
through BCM terminal 54
●
to power window main switch terminal 19
●
to front power window switch (passenger side) terminal 10.
With ignition switch in ON or START position,
Power is supplied
●
through 10A fuse [No.1,located in the fuse block (J/B)]
●
to BCM terminal 38
●
through BCM terminal 53
●
to power window main switch terminal 10
●
to rear power window switch (LH and RH) terminal 1.
Ground supplied
●
to BCM terminal 52
●
through body grounds E13, E26 and E28
●
to power window main switch terminal 17
●
through body grounds M14 and M78
●
to front power window switch (passenger side) terminal 11
●
through body grounds M14 and M78
MANUAL OPERATION
Front Driver Side Door
WINDOW UP
When the front driver side switch in the power window main switch is pressed in the up position,
Power is supplied
●
through power window main switch terminal 8
●
to front power window motor (driver side) terminal 2.
Ground is supplied
●
to front power window motor (driver side) terminal 1
●
through power window main switch terminal 11.
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the front driver side switch in the power window main switch is pressed in the down position
Power is supplied
●
through power window main switch terminal 11
●
to front power window motor (driver side) terminal 1.
Ground is supplied
●
to front power window motor (driver side) terminal 2
●
through power window main switch terminal 8.
Then, the motor lowers the window until the switch is released.
POWER WINDOW SYSTEM
GW-19
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2005 August
2005 Murano
Front Passenger Side Door
FRONT POWER WINDOW SWITCH (PASSENGER SIDE) OPERATION
WINDOW UP
When the front power window switch (passenger side) is pressed in the up position
Power is supplied
●
through front power window switch (passenger side) terminal 8
●
to front power window motor (passenger side) terminal 2.
Ground is supplied
●
to front power window motor (passenger side) terminal 1
●
through front power window switch (passenger side) terminal 9.
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the front power window switch (passenger side) is pressed in the down position
Power is supplied
●
through front power window switch (passenger side) terminal 9
●
to front power window motor (passenger side) terminal 1.
Ground is supplied
●
to front power window motor (passenger side) terminal 2
●
through front power window switch (passenger side) terminal 8.
Then, the motor lowers the window until the switch is released.
POWER WINDOW MAIN SWITCH OPERATION
Signal is sent
●
though power window main switch terminal 14
●
to front power window switch (passenger side) terminal 16.
The operation of power window after receive the signal is as same as operate the power window with sub-
switch (front passenger side).
Rear Door (LH or RH)
REAR POWER WINDOW SWITCH (LH OR RH) OPERATION
WINDOW UP
When the rear power window switch (LH or RH) is pressed in the up position
Power is supplied
●
through rear power window switch (LH or RH) terminal 5
●
to rear power window motor (LH or RH) terminal 2.
Ground is supplied
●
to rear power window motor (LH or RH) terminal 1
●
through rear power window switch (LH or RH) terminal 4.
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the rear power window switch (LH or RH) is pressed in the down position
Power is supplied
●
through rear power window switch (LH or RH) terminal 4
●
to rear power window motor (LH or RH) terminal 1.
Ground is supplied
●
to rear power window motor (LH or RH) terminal 2
●
through rear power window switch (LH or RH) terminal 5.
Then, the motor lowers the window until the switch is released.
POWER WINDOW MAIN SWITCH OPERATION
WINDOW UP
When the power window main switch (rear LH or RH) is pressed in the up position
Power is supplied
●
through power window main switch terminal 1 (LH) or 7 (RH)
●
through rear power window switch (LH or RH) terminal 2
GW-20
POWER WINDOW SYSTEM
Revision: 2005 August
2005 Murano
●
through rear power window switch (LH or RH) terminal 5
●
to rear power window motor (LH or RH) terminal 2.
Ground is supplied
●
to rear power window motor (LH or RH) terminal 1
●
through rear power window switch (LH or RH) terminal 4
●
through rear power window switch (LH or RH) terminal 3
●
through power window main switch terminal 3 (LH) or 5 (RH).
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the power window main switch (rear LH or RH) is pressed in the down position
Power is supplied
●
through power window main switch terminal 3 (LH) or 5 (RH)
●
through rear power window switch (LH or RH) terminal 3
●
through rear power window switch (LH or RH) terminal 4
●
to rear power window motor (LH or RH) terminal 1.
Ground is supplied
●
to rear power window motor (LH or RH) terminal 2
●
through rear power window switch (LH or RH) terminal 5
●
through rear power window switch (LH or RH) terminal 2
●
through power window main switch terminal 1 (LH) or 7 (RH)
Then, the motor raises the window until the switch is released.
AUTO OPERATION
The power window AUTO feature enables the driver to open or close the window without holding the window
switch in the down or up position.
POWER WINDOW SERIAL LINK
Power window main switch, front power window switch (passenger side) and BCM transmit and receive the
signal by power window serial link.
The under mentioned signal is transmitted from BCM to power window main switch and front power window
switch (passenger side)
●
Keyless power window down signal.
The under mentioned signal is transmitted from power window main switch to front power window switch (pas-
senger side)
●
Front passenger side door window operation signal.
●
Power window control by key cylinder switch signal.
●
Power window lock switch signal.
●
Retained power operation signal
POWER WINDOW LOCK
The power window lock is designed to lock operation of all windows except for driver side door window.
When the lock position, ground of the rear power window switches in the power window main switch is discon-
nected. This prevents the power window motors from operating.
POWER WINDOW SYSTEM
GW-21
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2005 August
2005 Murano
RETAINED POWER OPERATION
When the ignition switch is turned to the OFF position from ON or START position.
Power is supplied for 45 seconds
●
through BCM terminal 53
●
to power window main switch terminal 10.
●
to rear power window switch (LH and RH) terminals 1.
Then the power window can be operated.
When power and ground are supplied, the BCM continues to be energized, and the power window can be
operated.
The retained power operation is canceled when the driver or passenger side door is opened.
RAP signal period can be changed by CONSULT-II. Refer to
GW-37, "CONSULT-II Function (BCM)"
ANTI-PINCH SYSTEM
Power window main switch and front power window switch (passenger side) monitors the power window motor
operation and the power window position (full closed or other) for driver side and passenger side power win-
dow by the signals from encoder and limit switch in front power window motor (driver side and passenger
side).
When power window main switch detects interruption during the following close operation,
●
automatic close operation when ignition switch is in the “ON” position
●
automatic close operation during retained power operation
●
manual close operation during retained power operation
Power window main switch or power window sub-switch (passenger side) controls each power window regula-
tor motor for open and the power window will be lowered about 150 mm (5.91 in).
POWER WINDOW CONTROL BY THE KEY CYLINDER SWITCH
When ignition key switch is OFF, front power window can be opened or closed by turning the front door key
cylinder driver side UNLOCK / LOCK position more then 1.5 second over condition.
●
Power window can be opened as the door key cylinder is kept fully turning to the UNLOCK position.
●
Power window can be closed as the door key cylinder is kept fully turning to the LOCK position.
The power window opening stops when the following operations are carried out.
●
While performing open / close the window, power window is stopped at the position as the door key cylin-
der is placed on NEUTRAL.
●
When the ignition switch is turned ON while the power window opening is operated.
CAN Communication System Description
AIS004UF
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Unit
AIS004UG
Refer to
GW-22
POWER WINDOW SYSTEM
Revision: 2005 August
2005 Murano
Schematic/With Intelligent Key
AIS002CP
TIWB0172E
POWER WINDOW SYSTEM
GW-23
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2005 August
2005 Murano
Wiring Diagram — WINDOW —/With Intelligent Key
AIS002CQ
TIWB0291E
GW-24
POWER WINDOW SYSTEM
Revision: 2005 August
2005 Murano
TIWB0173E
POWER WINDOW SYSTEM
GW-25
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2005 August
2005 Murano
TIWB0174E
GW-26
POWER WINDOW SYSTEM
Revision: 2005 August
2005 Murano
TIWA0506E
POWER WINDOW SYSTEM
GW-27
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2005 August
2005 Murano
TIWB0175E
GW-28
POWER WINDOW SYSTEM
Revision: 2005 August
2005 Murano
Schematic/Without Intelligent Key
AIS0069Z
TIWB0279E
POWER WINDOW SYSTEM
GW-29
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2005 August
2005 Murano
Wiring Diagram — WINDOW —/Without Intelligent Key
AIS006A0
TIWB0280E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст