Fiat Doblo Panorama (2019 year). Manual — part 8
IN AN EMERGENCY
122
IN AN EMERGENCY
A punctured tyre or a burnt-out bulb?
At times, a problem may interfere with
our journey.
The pages on emergencies can help
you to deal with critical situations
independently and with calm.
In an emergency we recommend that
you call the freephone number found in
the Warranty Booklet.
It is also possible to call the 00 800
3428 0000 freephone number to
search the nearest Fiat Dealership.
HAZARD WARNING LIGHTS . ... 123
REPLACING A BULB . . . . .. 123
REPLACING AN EXTERIOR
BULB . . . . . . . . . ... 126
REPLACING INTERIOR BULBS . 129
REPLACING FUSES . . . . ... 130
REPLACING A WHEEL . . . ... 134
FIX&GO AUTOMATIC KIT . . . 138
EMERGENCY STARTING . . . 141
FUEL CUT-OFF SYSTEM . . . 142
LIFTING THE VEHICLE. . . . 142
TOWING THE VEHICLE . . . .. 142
-------------------------------------------------------------------------------------------------------------------------------------------------------------
123
HAZARD WARNING
LIGHTS
They are turned on by pressing switch
(A) fig. 153, regardless of the position
of the ignition key. Warning lights
and
are lit up in the instrument
panel when this device is activated.
Press the switch (A) again to turn the
lights off.
WARNING The use of hazard warning
lights is governed by the highway code
of the country you are in. Comply with
legal requirements.
153
F0V0513
Emergency braking
(for versions/markets, where provided)
In the event of emergency braking
the hazard warning lights come on
automatically, as do the
and
warning lights in the panel.
The function switches off automatically
when the nature of the braking
changes.
REPLACING A BULB
GENERAL
INSTRUCTIONS
Before replacing a bulb check the
contacts for oxidation;
burnt bulbs must be replaced by
others of the same type and power;
always check the height of the
headlight beam after changing a bulb,
for reasons of safety;
when a light is not working, check
that the corresponding fuse is intact
before changing a bulb. For the
location of fuses, refer to the paragraph
“If a fuse blows” in this section.
117) 118)
37) 38)
WARNING A slight misting may
appear on the internal surface of the
headlight: this does not indicate a fault
and is caused by low temperature
and the degree of humidity in the air.
Misting will rapidly disappear when
the headlights are switched on. The
presence of drops inside the headlights
indicates infiltration of water. Contact a
Fiat Dealership.
BULBS TYPES
Various types of bulbs are fitted to your
vehicle fig. 154:
154
F0V0027
A Glass bulbs: clipped into position.
Pull to extract.
B Bayonet type bulbs: to remove
from its holder, press the bulb, turn it
anticlockwise, then remove.
C Tubular bulbs: release them from
their contacts to remove.
D Halogen bulbs: to remove the
bulb, release the clip holding the bulb in
place.
E Halogen bulbs: to remove the bulb,
release the clip holding the bulb in
place.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN AN EMERGENCY
124
WARNING
117)
Modifications or repairs to the electric
system that are not carried out properly
or do not take the system technical
specifications into account can cause
malfunctions leading to the risk of fire.
118)
Halogen bulbs contain pressurised
gas, in the case of breakage they may
burst causing glass fragments to be
projected outwards.
IMPORTANT
37)
Halogen bulbs must be handled
holding the metallic part only. Touching
the transparent part of the bulb with your
fingers may reduce the intensity of the
emitted light and even reduce the lifespan
of the bulb. In the event of accidental
contact, wipe the bulb with a cloth
moistened with alcohol and let the bulb
dry.
38)
Where possible, it is advisable to have
bulbs changed at a Fiat Dealership. The
correct operation and direction of the
external lights are absolutely essential for
the safety of the car and of compliance
with the law.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
125
Light bulbs
Use
Type
Power
Ref. Figure
Main beams
H7
55W
E
Dipped headlights
H7
55W
E
Daytime running lights / side lights
W21W
13W
B
Front direction indicators
WY21W
21W
B
Side turn light
WY5W
5W
A
Rear direction indicators
PY21W
21W
B
Rear fog light
W16W
16W
A
Reverse gear
W16W
16W
A
Rear side lights
P21/5W
5W
B
Stop
P21W
21W
B
Third brake light wing
W5W
5W
A
Third brake light swinging
W5W
5W
A
Third brake light swinging (for privacy glass)
Xenon 6 W
6W
A
Front fog lights (for versions/markets where provided)
H11
55W
E
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN AN EMERGENCY
126
REPLACING AN
EXTERIOR BULB
For the type of bulb and relevant power
rating, see “Changing a bulb”.
FRONT LIGHT CLUSTERS
The front light clusters contain side
light, daytime running light, dipped,
main beam and direction indicator
bulbs fig. 155.
155
F0V0520
The bulbs are arranged inside the light
cluster as follows:
A Main beam headlights:
B Dipped beam headlights;
C Direction indicators and side
lights/daytime running lights.
To access the bulbs, remove the snap-
fitted covers.
SIDE LIGHTS/DAYTIME RUNNING
LIGHTS
To replace the bulb, proceed as
follows:
remove the protective cover
(C)fig. 155;
turn the bulb holder (A)fig. 156
anticlockwise and extract it;
extract the bulb and replace it;
refit the new bulb, put the bulb
holder (A)fig. 156 back into place
and then refit the protective cover
(C)fig. 155 properly.
156
F0V0521
DIPPED BEAM
HEADLIGHTS
To replace the bulb, proceed as
follows:
remove the protective cover
(B)fig. 155;
disconnect the electrical connector;
release the bulb holder from the side
clips (A)fig. 157;
extract the bulb and replace it;
fit the new bulb, ensuring that the
outline of the metal part coincides
with the grooves on the curve of the
headlight, pressing to engage it
with the side clips (A)fig. 157; then
reconnect the electrical connector;
correctly refit the protective cover
(B)fig. 155.
157
F0V0522
DIRECTION INDICATORS
Front
To replace the bulb, proceed as
follows:
remove the protective cover
(C)fig. 155;
rotate the bulb holder (A)fig. 158
anticlockwise and extract it;
extract the bulb, pushing it gently
and turning it anticlockwise;
replace the bulb and refit the
bulb holder (A)fig. 158 by turning it
clockwise and locking it properly into
place;
refit the protective cover (C)fig. 155.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
127
158
F0V0523
Side
WARNING Go to a Fiat Dealership
to have bulbs for the side direction
indicators replaced, because they are
located inside the door mirror.
MAIN BEAM HEADLIGHTS
To replace the bulb, proceed as
follows:
remove the protective cover
(A)fig. 155;
disconnect the electrical connector;
release the bulb holder from the side
clips (A)fig. 159;
extract the bulb and replace it;
fit the new bulb, ensuring that the
outline of the metal part coincides
with the grooves on the curve of the
headlight, pressing to engage it
with the side clips (A)fig. 159; then
reconnect the electrical connector;
correctly refit the protective cover
(A)fig. 155.
159
F0V0524
FOG LIGHTS
(for versions/markets, where provided)
WARNING Go to a Fiat Dealership to
have the front fog light bulbs replaced.
REAR LIGHT CLUSTERS
The rear light clusters contain the bulbs
for the side lights, direction indicators
and reversing/rear fog and brake lights.
To access the light clusters, proceed
as follows:
open the rear doors;
undo the fixing screws (A)fig. 160.
disconnect the electrical connector
and then remove the light cluster.
The bulbs are arranged inside the light
cluster fig. 161 as follows:
A Brake lights;
B Direction indicators;
C Reverse lights;
D Side/rear fog lights;
To access the bulbs, undo the 6 fixing
screws (E)fig. 161 and remove the bulb
holder.
To change the bulb, push it in gently
and turn it anticlockwise (“bayonet”
type), then remove and replace it.
160
F0V0034
THIRD BRAKE LIGHTS
To replace the bulb proceed as follows:
for versions with tailgate, undo the
two fixing screws (A)fig. 162 and
remove the unit;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN AN EMERGENCY
128
for versions with wing doors, remove
the rubber caps (B)fig. 163 and
manoeuvre the holding tabs (C), then
remove the unit;
161
F0V0525
162
F0V0163
163
F0V0164
for versions with high roof and swing
doors, remove the pressure-fit plastic
guard (A)fig. 164 and rubber cap
(B)fig. 164, using a screwdriver, release
the retaining tags as shown in the
figure and remove the unit;
164
F0V0231
manoeuvre the appropriate tabs and
remove the bulb holder;
remove the snap-fitted bulb and
replace.
NUMBER PLATE
LIGHTS (for hatchback
versions)
To replace the bulbs (A) fig. 165,
proceed as follows:
165
F0V0179
manoeuvre the holding tabs at the
points indicated by the arrows, and
remove the bulb holder;
turn the bulb holder (B) fig. 166
anticlockwise, then remove bulb (C).
166
F0V0037
-------------------------------------------------------------------------------------------------------------------------------------------------------------
129
NUMBER PLATE LIGHTS
(for versions with wing
doors)
To replace the bulbs (A) fig. 167,
proceed as follows:
167
F0V0036
manoeuvre the holding tabs at the
points indicated in the diagram, and
remove the lens by lifting to the left;
remove the bulbs by releasing them
from the side contacts; insert the new
bulbs and make sure they are correctly
clamped between these contacts.
REPLACING
INTERIOR BULBS
For the type of bulb and relevant power
rating, see “Changing a bulb”.
FRONT/REAR CEILING
LIGHT
Ceiling light with movable lens
To replace the bulbs, proceed as
follows:
extract the ceiling light (A) fig. 168 by
operating in the points shown by the
arrows;
168
F0V0070
open the lid (B) fig. 169 as shown;
remove bulb (C) fig. 170 by releasing
it from the side contacts, then insert
the new bulb and make sure it is
correctly clamped between these
contacts;
169
F0V0071
170
F0V0072
close the cover and secure the
ceiling light into its housing, making
sure it locks properly into place.
Ceiling light with spot lights (where
provided)
To replace the bulbs, proceed as
follows:
operate in the points shown by the
arrow and remove ceiling light (A)
fig. 171;
open protective flap (B) fig. 172;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN AN EMERGENCY
130
171
F0V0073
172
F0V0074
replace the bulbs (C) by releasing
them from the side contacts and
making sure that the new bulbs
are correctly secured between the
contacts;
re-close the flap (B) fig. 172 and
fasten the ceiling light (A) fig. 171 in its
housing, making sure that it locks into
place.
REPLACING FUSES
119) 120) 121)
39) 40) 41)
GENERAL INFORMATION
To change a fuse, use the tongs
located in the tool box or the Fix & Go
container (for versions/markets where
provided).
Methane system protection fuses
The CNG system components are
protected by specific fuses. Contact a
Fiat Dealership for replacement.
ENGINE COMPARTMENT
FUSEBOX
The fusebox fig. 175 is located on the
right-hand side of the engine, next to
the battery. To remove the protective
cover (A) fig. 173 and access the
fusebox, undo the two fixing screws
(B).
42)
173
F0V0081
PASSENGER
COMPARTMENT
FUSEBOXES
To access the fuses, remove snap-
fitted protective cover (A) fig. 174.
174
F0V0562
The fuses are positioned in the two
areas shown in fig. 176.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
131
175
F0V0089
176
F0V0563
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN AN EMERGENCY
132
Engine compartment fusebox fig. 173 - fig. 175
PROTECTED DEVICE
FUSE
AMPERE
Remote control switch for opening swing door (Cargo version)
F09
10
Single tone horn
F10
10
Main beams
F14
15
Heated rear window
F20
30
Fog lights
F30
15
Rear power socket
F85
15
Passenger compartment power socket
F86
15
-------------------------------------------------------------------------------------------------------------------------------------------------------------
133
Passenger compartment fuseboxes fig. 174 - fig. 176
PROTECTED DEVICE
FUSE
AMPERE
Door locking/unlocking motors, dead lock actuator motors, tailgate unlocking motor
F38
20
Supply + battery for EOBD diagnosis socket, radio, tyre pressure monitoring control unit
F36
10
Windscreen/rear window washer pump
F43
15
Window winder motor for front door passenger side
F48
20
Left low beam, headlight corrector
F13
7.5
Window winder motor for front door driver's side
F47
20
Heated driver seat
F1
10
Heated passenger seat
F2
10
Cigarette lighter
F3
15
Third power socket on dashboard
F4
20
Driver's side rear electric window
F5
20
Passenger's side rear electric window
F6
20
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN AN EMERGENCY
134
WARNING
119)
If the replaced fuse blows again,
contact a Fiat Dealership.
120)
Never replace a fuse with another
with a higher amp rating; RISK OF FIRE. If
a general protection fuse (MEGA-FUSE,
MIDI-FUSE) is activated, contact a Fiat
Dealership. Before replacing a fuse,
make sure that the ignition key has been
removed and that all the other services are
switched off and/or disengaged.
121)
Contact Fiat Dealership if a safety
system (airbags, brakes), engine system
(engine, transmission) or steering system
general protection fuse blows.
IMPORTANT
39)
Never replace a faulty fuse with metal
wires or anything else.
40)
The Comfort-Matic/Dualogic system
components are protected by specific
fuses. Contact a Fiat Dealership for
replacement.
41)
The Natural Power system
components are protected by specific
fuses. Contact a Fiat Dealership for
replacement.
42)
If you need to wash the engine
compartment, take care not to directly hit
the fuse box and the window wiper motors
with the water jet.
REPLACING A
WHEEL
The vehicle is originally equipped with
the Fix&Go automatic quick tyre repair
kit (see instructions in the next section).
As an alternative, the vehicle may have
a normal-sized spare wheel.
Wheel changing and correct use of
the jack and spare wheel call for some
precautions, as listed below.
122) 123) 124) 125)
Note for one-way tyres
One-way tyres have a few arrows
on the side indicating the rotation
direction. If a wheel is changed (when
punctured, for example) the direction of
the arrows on the spare wheel tyre may
not coincide with the rotation direction
of the wheel to be replaced.
In these conditions, too, the tyre still
maintains its safety features.
Anyway, it is recommended to have the
wheel repaired and refitted as soon as
possible, as the best performance is
achieved when the rotation direction
of all tyres coincides with the one
indicated by the arrows.
JACK
Please note that:
the jack weight is 4 kg;
the jack requires no adjustment;
the jack cannot be repaired and in
the event of a fault it must be replaced
by another genuine one;
no tool other than its cranking device
may be fitted on the jack.
WHEEL REPLACEMENT
PROCEDURE
To change a wheel, proceed as
follows:
stop the vehicle in a position that is
not dangerous for oncoming traffic
where you can change the wheel
safely. The ground must be flat and
sufficiently compact;
switch off the engine and pull the
handbrake;
engage first gear or reverse;
wear the reflective safety jacket
(compulsory by law in certain countries)
before getting out of the vehicle;
indicate that the vehicle has broken
down using the devices required by the
law in the current country (e.g. warning
triangle, hazard lights, etc.);
for Cargo versions fig. 177: move the
left front seat forward and operate lever
A to access the tool bag; take it to the
wheel that needs replacing;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
135
177
F0V0149
for Doblò/Doblò Combi versions
fig. 178: open the rear doors, inside
the compartment on the rear right side,
take the tool bag, unhooking the elastic
band from the buckle, and take it next
to the wheel to be changed;
178
F0V0148
take wheel spanner (B) fig. 179 and
the extension with pentagonal fitting
(C); inside the load area, fit extension
(C) on bolt (A); use spanner (B) to lower
the wheel by unwinding the wire;
B
C
179
F0V0150
use the wheel dismantling spanner
B to remove the wheel from the vehicle
fig. 180;
180
F0V0151
unscrew knob (D) fig. 181 and
release the rim from bracket (E),
removing it from the hole of the rim;
181
F0V0193
For Cargo Natural Power versions
with spare wheel, available on demand,
is placed in the rear zone on the right of
the loading compartment;
182
F0V0248
The wheel can be removed by
unscrewing the two bolts (A) - fig. 182
that fix it to the support. This has a
pin (A) - fig. 183 that allows correct
positioning and makes it easier to fix
the spare wheel.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN AN EMERGENCY
136
183
F0V0249
for versions with alloy rims, remove
the press-fitted hub cap;
loosen the fixing bolts of the wheel to
be replaced by about one turn, using
the spanner provided;
remove wedge (D) from the tool bag
and open it as shown in fig. 184;
184
F0V0192
place the wedge (D) behind the
wheel diagonally opposite the one you
want to replace fig. 185 to prevent the
vehicle from moving when it is raised.
185
F0V0153
operate the jack using the knob
(release the handle from the clip and
the hole on the nut) in order to open it
partially fig. 186, then position it under
the vehicle in line with references (A)
fig. 187 near the wheel to be changed.
186
F0V0154
187
F0V0155
operate the jack with the knob to
open it until the groove (A) fig. 188
of the jack is correctly inserted in the
lower profile (B) on the side member;
188
F0V0156
warn anybody nearby that the vehicle
is about to be lifted. They must stay
clear and not touch the vehicle until it is
back on the ground.
introduce the handle in the hole
on the nut and the plastic clip, then
operate the jack and raise the vehicle,
until the wheel is a few centimetres off
the ground. When turning the crank,
-------------------------------------------------------------------------------------------------------------------------------------------------------------
137
ensure that it rotates freely in order to
avoid grazing your hands against the
ground. The moving components of
the jack (screws and joints) can also
cause injuries: avoid touching them. If
you come into contact with lubricating
grease, clean yourself thoroughly;
fully loosen the fixing bolts and
remove the wheel;
make sure the contact surfaces
between spare wheel and hub are
clean so that the fastening bolts will not
come loose;
fit the standard wheel by inserting the
first bolt (B) fig. 189 two threads into
the hole closest to the inflation valve
(A);
189
F0V0157
fit the hub cap, making sure that the
symbol
(on the cup) aligns with the
inflation valve, and then insert the other
three bolts;
tighten the bolts using the spanner
provided;
turn the jack handle to lower the
vehicle, and remove the jack;
use the wrench provided to fully
tighten the bolts, passing alternately
from one bolt to the opposite one, as
per the numerical sequence illustrated
in fig. 190.
190
F0V0158
At the end of the operation
fix bracket (A) fig. 191 to the wheel
after passing it through the hole, insert
the threaded pin into one of the bolt
holes and secure by tightening knob
(B);
191
F0V0194
for vehicles with alloy rims take the
adapter (D) fig. 192 and fit the plastic
spacer (C) between the spring and
the flange of the bracket. The plastic
fin must be directed downwards and
perfectly coincide with the flange cut
part;
192
F0V0214
fit the bracket (E) fig. 193 in the
adapter (D), fit the pin in the hole and
fasten by the knob (F);
193
F0V0215
position the wheel vertically and rest
the fitted adaptor on the inside of the
rim, then using the screws provided
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст