Fiat Tipo 4Door (2021 year). Manual in english — page 3
KNOWING THE INSTRUMENT PANEL
42
INSTRUMENT PANEL FEATURES
BASIC INSTRUMENT PANEL
56
P2000234
1. Speedometer 2. Multifunction display 3. Tachometer 4. Fuel level digital gauge with reserve warning light 5. Digital engine
coolant temperature gauge with overheating warning light
WARNING The illumination of the instrument panel graphics may vary according to version.
43
PREMIUM INSTRUMENT PANEL
57
P2000235
1. Digital tachometer 2. Digital speedometer 3. Fuel level digital gauge with reserve symbol
WARNING The illumination of the instrument panel graphics may vary according to version.
KNOWING THE INSTRUMENT PANEL
44
INSTRUMENT PANEL
LIGHT ADJUSTMENT
(brightness sensor)
(versions with colour display)
Versions with colour display are
equipped with a brightness sensor
(fitted inside the instrument panel)
capable of detecting ambient light
conditions and adjusting the brightness
of the instrument panel accordingly.
The behaviour of the instrument is as
follow:
"daytime" mode: the display can be
set to 8 levels;
"night time" mode: the display can be
set to 8 levels.
The brightness of the automatic dual
zone climate control display and
Uconnect display (for version/markets,
where provided) is also adjusted.
For adjusting, see the "Display"
paragraph in this chapter.
DISPLAY
DESCRIPTION
The car is equipped with a display that
can show useful information to the
driver while driving.
With the ignition device in STOP
position and ignition key removed, the
display lights up and shows the time
and total odometer reading (in km or
miles) for a few seconds when a door is
opened/closed.
GEAR SHIFT INDICATOR
The Gear Shift Indicator (GSI) system
gives an indication ((4) fig. 58 for
versions with basic display or (1)
fig. 59) on the premium display of the
instrument panel to advise the driver
when to change gear.
58
P2000078-000-000
59
P2000324
Through the GSI, the driver is informed
that the gear change will allow a
reduction in fuel consumption.
45
When the
symbol appears on the
display, the GSI is advising the driver to
shift up, while the
symbol advises
the driver to shift down.
The indication in the display remains
until a gear is shifted or the driving
conditions go back to a situation where
gearshifting is not required to improve
consumption.
On some versions, the engaged
gear and the recommended one are
displayed next to the
or
symbol.
Icons
or
may appear when
the GSI recommends shifting to a gear
two steps higher than the currently
engaged one. On these versions, the
system only displays the engaged gear
when the driving conditions do not
make it necessary to change gear to
optimise fuel consumption.
The indications of the engaged gear
and the recommended gear shift
temporarily disappear from the display
during a gear shift and reappear as
soon as the gear shift is finished.
BASIC DISPLAY
The display fig. 60 will show the
following information:
60
P2000078-000-000
1
: headlight alignment position,
indication of the gear engaged, outside
temperature, compass (where present),
date.
2
: vehicle speed, warning
messages/any failure indications.
3
: total kilometres (or miles) run and
symbols of any failure indications.
4
: indication of the suggested gear
shift (GSI).
MAIN MENU
The Menu includes the following items:
TRIP
GSI
VEHICLE INFO
DRIVER ASSIST
AUDIO (function available in versions
and markets where present)
PHONE (function available in versions
and markets where present)
NAVIGATION (function available in
versions and markets where present)
ALERTS
VEHICLE SETUP
Vehicle Setup
This menu item allows you to change
the settings for:
Display;
Units;
Clock & Date;
Safety;
Safety & Assistance;
Lights;
Doors & Locks;
Display
By selecting item "Display" you
can access the settings/information
regarding: "Display Settings”,
Language", “Automatic reset Trip B”,
"See phone" (available in versions
and markets where present), "See
navigation" (available in versions and
markets where present), "Display
lighting”.
KNOWING THE INSTRUMENT PANEL
46
Units
Select item "Units" to choose the unit
of measurement between: "Imperial",
"Metric", "Customised".
Clock & Date
Select item "Clock & Date" to make
the following adjustments: "Set Time",
"Time Format", "Set Date".
Safety
Select item "Safety" to make the
following adjustments: "Passenger
AIRBAG", "Speed beep", "Seat belt
buzzer".
"Passenger AIRBAG" adjustment
allows you to activate/deactivate
the passenger airbag.
Passenger's
protection not active
: the LED
comes on constantly in the
instrument panel dashboard.
Safety & Assistance
Select item "Safety & Assistance" to
make the following adjustments: Rain
sensor, Buzzer volume, Park Assist,
Park Assist Volume, Autonomous
Emergency Brake Control (AEB
Control), Traffic Sign Assist, Traffic
Sign Alarm, New speed limit alert,
Lane Control Warning, Lane Control
Strength, Driver Attention Assist,
Park Assist rear sensor volume (for
versions/markets, where provided),
Park Assist front sensor volume (for
versions/markets, where provided).
Lights
Select item "Lights" to make the
following adjustments: "Courtesy
lights", “Automatic lights”, "Daytime
running lights", "Cornering lights",
"Headlamp sensor", "Follow me home".
Doors & Locks
Select item "Doors & Locks" to make
the following adjustments: "Autoclose",
"Flash Lights w/Lock", "Auto unlock
on exit”, “Remote unlock”, “Keyless
Entry/Go”.
NOTE With the
system,
some Menu items are shown and
managed on the display of the latter
and not on the instrument panel display
(refer to the dedicated Multimedia
chapter or to the supplement available
online).
CONTROL BUTTONS
These are located on the left side of the
steering wheel fig. 61.
They allow the driver to select and
interact with the items in the Main
menu of the display (see paragraph
"Main menu").
61
P2000302
/ : press and release the
buttons to access the Main menu and
to scroll the menu and the submenus
upwards or downwards.
/ : press and release the
buttons to access the information
screens or the submenus of an item of
the Main menu.
OK
: press this button to
access/select the info displays or the
submenus of an item of the Main
menu. Hold the button pressed for 1
second to reset the displayed/selected
functions.
PREMIUM DISPLAY
The display fig. 62 will show the
following information:
47
62
P2000237
Top left/right area (1):
compass,
external temperature, date, time, trip A
trip B, speedometer (depending on the
display customisation).
Central area of the display
(2):
speed, car status information,
fuel consumption information, trip
computer, audio repetition, warning
messages/ fault messages, display and
car settings.
Fuel use information (3).
DISPLAY PAGES
You can navigate through the following
main and detail screens using the
controls on the left side of the steering
wheel:
Screenshot list
/
Main screen
By pressing and releasing
/
the user can choose to display:
the multifunction dial indicator
showing the speed of the car
or:
the multifunction dial indicator
showing the speed of the car, plus
the indicator recommending the
gear to engage
Trip
Press and release
/
:
Trip A
Trip B
Driver assist
Vehicle info
Press and release
/
:
Tyre pressure
Coolant temp
Oil temperature
Oil life
Battery charge
AdBlue
Service (scheduled servicing)
Audio
Phone
Navigation
Alerts
/
Settings
Display
Safety
Safety/Assistance
Engine switch off procedure
In the case of multiple screens,
indicates the presence of screens
to the right and/or left of those
displayed. Scrolling between
pages is possible using the arrows
/
.
Trip computer
The "Trip computer" page (fig. 63) can
be used to view several parameters
relating to the operational status
of the car. This function has two
separate memories, "Trip A" and
"Trip B", where the data for the car's
"complete journeys" (trips) is recorded
independently from each other.
Press the
or
button to switch
from "Trip A" to "Trip B" and vice versa.
63
P2000245
KNOWING THE INSTRUMENT PANEL
48
The screen can be used to show the
following items: "Current consumption",
"Average consumption", "Distance",
"Average speed", "Travel time".
The sizes are displayed in "km"/"mi"
and "km/h"/"mph" depending on the
display settings.
Both values can be reset: press and
hold down the OK button on the
steering wheel.
NOTE The total consumption cannot
be reset.
Driver assist
This screen shows the messages and
visual indicators related to the following
driving assistance systems in area
(1) fig. 64 (for the basic display) or (1)
fig. 65 (for the premium display):
CC (Cruise Control)
ACC (Adaptive Cruise Control);
TSR (Traffic Sign Recognition) / TSI
(Traffic Sign Information);
ISA (Intelligent Speed Assist).
As more recent notifications are shown,
previous notifications are overwritten.
64
P2000286
65
P2000246
For some driving assistance devices,
pop-up warnings are marked in yellow
or red at the bottom of the screen
depending on the type of warning
fig. 66.
66
P2000236
Refer to the "Starting and Driving"
section for more information about
driving assistance systems.
Vehicle info
The screen shows the following
information:
Tyre pressure
Service (scheduled servicing)
Press the
or
button to switch
between the "Tyre pressure" screen
and the "Service" screen.
Audio
(where provided)
This screen repeats the audio playback
information shown on the
system:
FM/DAB radio;
Media (USB,
Bluetooth®
);
49
Android Auto, Apple CarPlay, Baidu
Carlife.
Refer to the "Multimedia" section for
more information.
Phone
(where provided)
This screen repeats the information
displayed on the
system
while interacting with a paired phone.
The following information is shown:
Call status;
connected phone status (battery
state of charge, network reception,
incoming/outgoing call notification,
received text messages notification);
recent call list.
The system stores the last 10
received messages marked "read"
or "unread". The user can select the
desired message using the steering
wheel controls
/
and open it by
pressing the OK button on the steering
wheel.
Refer to the "Multimedia" section for
more information.
Navigation
(where provided)
This screen repeats the instructions
provided by the
system
navigator. The display can be
pictogram or map.
Refer to the "Multimedia" section for
more information.
Alerts
This screen displays the recorded
messages and pop-ups previously
displayed by the user (fig. 67).
(1) Symbol (where provided)
(2) Message
67
P2000247
Settings
This screen allows you to customise
the displays and notifications on the
display and the various functions of the
car.
NOTE The tachograph components are
illustrated below. The menus may vary
depending on the equipment of the car.
NOTE Some settings may be managed
using the
system (see
"Settings" in the "Vehicle mode"
paragraph in the "Multimedia" section).
Display
Screen Setup: customisation of
the bottom left corner, centre and
bottom right corner of the display
(external temperature, date, time,
compass, odometer, audio info,
phone info).
Dimmer: screen brightness.
Reset trip B (never/always/every
2h/every 8h).
See phone: enable/disable.
See navigation: enable/disable.
Units of measurement: metric/
imperial.
Customisable sizes: Speed, Distance,
Consumption, Pressure, Temperature.
Date and Time
Time adjustment.
Format adjustment: 12
hours/24 hours.
Date setting.
Safety
Passenger AIRBAG.
Seat belt buzzer:
enable/disable.
Speed beep: volume
adjustment.
Safety/Assistance
Acoustic alert volume: off, low
level, medium level, high level.
Intelligent Speed Limiter:
confirmation, automatic.
KNOWING THE INSTRUMENT PANEL
50
Traffic Sign Assist: enable,
disable.
Traffic Sign Assist alert: off,
visual, visual and acoustic.
New speed limit zone detection:
off, visual, visual and acoustic.
Autonomous Emergency Brake
Control (AEB Control): off/active
braking only/active braking with
alert.
Autonomous Emergency Brake
Control (AEB Control) sensitivity:
near/medium/far.
Park Assist: acoustic, acoustic
and visual.
Volume Rear Park Assist: near,
medium, far.
Attention Assist warning:
enable, disable.
Mirrors and windscreen wipers
Rain sensor: enable, disable.
Lights
Dipped beam sensitivity: 1 to 3.
Follow me Home: 0, 30, 60, 90
seconds.
Automatic main beam: enable,
disable.
DRL (Daytime Running Lights):
enable, disable.
Cornering lights: enable,
disable.
Dipped beam auto power off:
enable, disable.
Doors & Locks
Automatic locking: enable,
disable.
Automatic unlock on exit:
enable, disable.
Dipped beam when closing:
enable/disable.
Remote door unlocking: all
doors, driver doors.
Passive Entry: enable, disable.
Start pairing process: start the
procedure.
Motor shutdown procedure: start the
procedure.
EOBD SYSTEM
(European On
Board Diagnosis)
(where provided)
Operation
The EOBD (European On Board
Diagnosis system) carries out
a continuous diagnosis of the
components of the car related to
emissions.
It also alerts the driver, by switching on
the warning light
on the instrument
panel, together with a message on
the display, when these components
are no longer in peak condition (see
“Warning lights and messages”
paragraph in this chapter).
The aim of the EOBD system
(European On Board Diagnosis) is to:
monitor the efficiency of the system;
indicate an increase in emissions;
indicate the need to replace
damaged components.
The car also has a connector, which
can interface with appropriate tools,
that makes it possible to read the error
codes stored in the electronic control
units together with a series of specific
parameters for engine operation and
diagnosis.
This check can also be carried out by
the traffic police.
WARNING After eliminating the
anomaly, to check the system
completely, a Fiat Dealership is obliged
to run tests and, if necessary, road
tests which may also require a long
journey.
51
WARNING LIGHTS AND MESSAGES
WARNING The warning light switches on together with a dedicated message and/or acoustic signal when applicable. These
indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the
information contained in the Owner Handbook, which you are advised to read carefully in all cases. Always refer to the
information in this section in the event of a failure indication.
IMPORTANT Failure indications displayed are divided into two categories: very serious and less serious failures. Serious faults
are indicated by a repeated and prolonged warning "cycle". Less serious faults are indicated by a warning "cycle" with a shorter
duration. The display cycle of both categories can be interrupted. The instrument panel warning light will stay on until the cause
of the failure is eliminated.
NOTE The warning lights and symbols described below are indicative and can change based on the version or market.
KNOWING THE INSTRUMENT PANEL
52
Red warning lights
Warning light
What it means
red
INSUFFICIENT BRAKE FLUID / PARKING BRAKE ON
Low brake fluid level
The warning light turns on when the level of the brake fluid in the reservoir falls below the minimum level, possibly
due to a leak in the circuit. Restore the brake fluid level, then check that the warning light has switched off. If the
warning light stays on, contact a Fiat Dealership.
Parking brake on
The warning light switches on when the parking brake is engaged.
red
POWER STEERING FAILURE
This warning light (or symbol in the display) switches on when the ignition device is brought to MAR, but it
should switch off after a few seconds. If the warning light (or symbol on the display) remains on, you could not
have steering assistance and the effort required to operate the steering wheel could be increased; steering is,
however, possible. Contact a Fiat Dealership as soon as possible.
red
amber
EBD FAILURE
The simultaneous switching on of the
(red) and
(amber) warning lights with the engine on indicates either
a failure of the EBD system or that the system is not available. In this case, the rear wheels may suddenly lock
and the vehicle may swerve when braking sharply.
Drive very carefully to the nearest Fiat Dealership to have the system inspected immediately.
red
SEAT BELTS REMINDER
The warning light switches on constantly if the vehicle is stationary and the driver side or passenger side seat
belt (for versions/markets, where provided), with the passenger seated, is not fastened. The warning light flashes
and an acoustic warning will sound if the car is in motion and the driver side or passenger side seat belt (for
versions/markets, where provided), with the passenger seated, is not correctly fastened. In this case, fasten the
seat belt.
53
Warning light
What it means
red
ENGINE COOLANT TEMPERATURE TOO HIGH
The warning light turns on when the engine is overheated.
In normal driving conditions
: stop the car, switch off the engine and check that the coolant level in the
reservoir is not below the MIN mark. In this case, wait for the engine to cool down, then slowly and carefully
open the cap, top up with coolant and check that the level is between the MIN and MAX marks on the reservoir
itself. Also check visually for any fluid leaks. If, when restarting, the warning light on the display switches on
again, contact a Fiat Dealership.
If the vehicle is used under demanding conditions
(e.g. in high-performance driving): slow down and, if
the warning light stays on, stop the vehicle. Stop for two or three minutes with the engine running and slightly
accelerated to facilitate better coolant circulation, then turn the engine off. Check that the coolant level is correct
as described above.
IMPORTANT Over demanding routes, it is advisable to keep the engine running and slightly accelerated for a few
minutes before turning it off.
red
AIRBAG FAILURE
If the warning light switches on constantly, this indicates a failure in the airbag system.
35) 36)
KNOWING THE INSTRUMENT PANEL
54
Amber warning lights
Warning light
What it means
amber
GENERIC FAILURE (where provided)
When this warning light or symbol starts flashing, for versions/markets where provided, this indicates an airbag
warning light fault. In this case, the airbag may not indicate possible airbag system malfunctions. Contact a Fiat
Dealership immediately.
When this warning light or symbol turn on, it can indicate the intervention or a problem concerning the fuel cut-off
system or an engine oil pressure sensor failure.
amber
iTPMS
iTPMS failure/iTPMS temporarily deactivated
The warning light flashes for about 75 seconds and then stays on constantly (together with a message on
the display) to indicate that the system is temporarily deactivated or faulty. The system will go back to normal
operation when the operating conditions will allow it. If this is not the case, carry out the Reset procedure after
restoring the normal operating conditions.
If the malfunction warning persists, contact a Fiat Dealership as soon as possible.
Low tyre pressure
The warning light switches on constantly to indicate that the pressure of one or more tyres is lower than the
recommended value and/or that slow pressure loss is occurring. In these cases, optimal tyre duration and fuel
consumption may not be guaranteed. It is advisable to restore the correct pressure value (see the "Wheels"
paragraph in the "Technical Specifications" section).
Once the normal operating conditions of the car are restored, carry out the "Reset" procedure.
IMPORTANT Do not continue driving with one or more flat tyres as the car handling may be compromised. Stop
the car, avoiding sharp braking and steering.
amber
ABS FAILURE
The warning light switches on to indicate an ABS fault. In this case the braking system maintains its efficiency
unaltered but without the advantage of the ABS system. Drive carefully and contact a Fiat Dealership as soon as
possible.
amber
ESC SYSTEM
ESC system activation
Intervention by the system is indicated by the flashing of the warning light: it indicates that the car is in critical
stability and grip conditions.
55
Warning light
What it means
amber
ESC system failure
If the warning light does not switch off, or if it stays on with the engine running, a failure was found on the ESC
system. Contact a Fiat Dealership as soon as possible.
Hill Hold Control system failure
The warning light turns on to indicate a Hill Holder Control system failure. Contact a Fiat Dealership as soon as
possible.
amber
PARTIAL DEACTIVATION OF ACTIVE SAFETY SYSTEMS
The warning light switches on to indicate that some active safety systems have been partially deactivated. When
the systems are reactivated, the warning light switches off.
amber
REAR FOG LIGHT
The warning light switches on when the rear fog light is activated.
amber
INJECTION / EOBD SYSTEM FAILURE
In normal conditions, when the ignition device is brought to MAR, the warning light switches on, but it should
switch off as soon as the engine is started. The operation of the warning light may be checked by the traffic
police using specific devices. Comply with the laws and regulations of the country where you are driving.
11)
Injection system failure
If the warning light remains on, or it switches on whilst driving, the injection system is not working properly. The
warning light on constantly signals a malfunction in the supply/ignition system which could cause high exhaust
emissions, a possible loss of performance, poor driveability and high consumption. The warning light switches off
if the malfunction disappears, but is still stored by the system. Under these conditions, the vehicle can continue
travelling at moderate speed but without demanding excessive effort from the engine or high speed. Prolonged
use of the car with the warning light on fixed may cause damage. Contact a Fiat Dealership as soon as possible.
Catalytic converter damaged
If the warning light flashes, it means that the catalytic converter may be damaged.
Release the accelerator pedal to lower the speed of the engine until the warning light stops flashing. Continue the
journey at moderate speed, trying to avoid driving conditions that may cause further flashing and contact a Fiat
Dealership as soon as possible.
KNOWING THE INSTRUMENT PANEL
56
Warning light
What it means
amber
UREA INJECTION SYSTEM FAILURE (Diesel versions)
(for versions/markets, where provided)
The warning light switches on, together with a dedicated message on the display (for versions/markets, where
provided) if a fluid not conforming with the nominal characteristics is inserted or if an average consumption of
UREA over 50% is detected.
Contact a Fiat Dealership as soon as possible.
If the problem is not solved, a specific message will appear on the instrument panel display whenever a certain
threshold is reached until it will no longer be possible to start the engine.
When 200 km will remain to prevent the engine restart, a continuous dedicated message will appear on the
dashboard (for versions/markets, where provided) accompanied by an acoustic warning sound.
amber
GLOW PLUG PREHEATING (Diesel versions)
This warning light comes on when the ignition device is brought to MAR and will switch off when the glow plugs
have reached the preset temperature. The engine can be started as soon as the warning light switches off.
IMPORTANT In mild or high temperature conditions, the warning light comes on for a very short time only.
GLOW PLUG PREHEATING FAILURE (Diesel versions)
The warning light will flash to indicate a failure in the glow plug preheating system. In this case, contact a Fiat
Dealership as soon as possible.
amber
FUEL RESERVE / LIMITED RANGE
This warning light on the display comes on when about 5 to 7 litres of fuel are left in the tank.
12)
amber
LPG RESERVE / LIMITED RANGE
(for LPG versions only)
This warning light on the display comes on when about 8 litres of LPG are left in the tank. An acoustic warning
goes on and the first notch of the LPG indicator stays on.
amber
AUTONOMOUS EMERGENCY BRAKE CONTROL OFF
(for versions/markets, where provided)
The warning light comes on when the Autonomous Emergency Brake Control (AEB Control) system is
deactivated by the driver or in the event of automatic deactivation following a temporary system failure. Contact a
Fiat Dealership as soon as possible.
57
Warning light
What it means
amber
START&STOP SYSTEM MANUAL ACTIVATION / DEACTIVATION
(for versions/markets, where provided)
Activation
: A message will appear, where provided, on the display when the system is activated.
Deactivation
: A warning light and, where provided, a dedicated message will appear on the display when the
Start&Stop system is deactivated.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст