Kia Mentor / Sephia Electrical System. Manual — part 34

future problem.
* Example: The customer desires improved ride and/or handling,
but the vehicle's shocks or struts have not failed. In this
case, replacement may be suggested to satisfy the customer's
wishes. In this case, replacement of the shocks or struts
may not be sold as a requirement.

A customer, of course, has the choice of whether or not a
shop will service his or her vehicle. He or she may decide not to
follow some of your suggestions. When a repair is required, a MAP shop
must refuse partial service on that system if, in the judgment of the
service provider, proceeding with the work could create or continue an
unsafe condition.
When presenting suggested repairs to the customer, you must
present the facts, allowing the customer to draw their own conclusions
and make an informed decision about how to proceed.
The following reasons may be used for required and suggested
services. These codes are shown in the "Code" column of the MAP
Uniform Inspection & Communications Standards that follow:

Reasons to Require Repair or Replacement

A - Part no longer performs intended purpose
B - Part does not meet a design specification (regardless of
performance)
C - Part is missing

NOTE: When a repair is required, the shop must refuse partial
service to the system in question, if the repair creates or
continues an unsafe condition.

Reasons to Suggest Repair or Replacement

1 - Part is close to the end of its useful life (just above
discard specifications, or weak; failure likely to occur
soon, etc.)
2 - To address a customer need, convenience, or request (to
stiffen ride, enhance performance, eliminate noise, etc.)
3 - To comply with maintenance recommended by the vehicle's
Original Equipment Manufacturer (OEM)
4 - Technician's recommendation based on substantial and
informed experience

NOTE: Suggested services are always optional. When presenting
suggested repairs to the customer, you must present the
facts, allowing the customer to draw their own conclusions

and make an informed decision about how to proceed.

ELECTRICAL SYSTEMS

SERVICE PROCEDURES REQUIRED AND SUGGESTED FOR PROPER

VEHICLE OPERATION

NOTE: When working on electrical systems, if a potentially
hazardous condition is observed, require repair or
replacement of affected components prior to performing
further work.

ACTUATOR MOTORS (SOLENOIDS) (ELECTRIC)

ACTUATOR MOTOR (SOLENOIDS) (ELECTRIC) INSPECTION

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Condition Code Procedure

Attaching hardware
broken . . . . . A ... Require repair or replacement
of hardware.
Attaching hardware
missing . . . . C . . .. Require replacement of
hardware.
Attaching hardware not
functioning . . . A ... Require repair or replacement
of hardware.
Connector broken . . A .. Require repair or replacement.
Connector (Weatherpack
type) leaking . . .. A .. Require repair or replacement.
Connector melted . . A . . ... (1) Require repair or
replacement.
Connector missing . ... C . . . Require replacement.
Inoperative . . . . A . . (2) Require replacement.
Linkage bent, affecting
performance . . . A ... Require repair or replacement
of linkage.
Linkage bent, not
affecting performance .. 2 ... Suggest repair or replacement
of linkage.
Linkage binding, affecting
performance . . . A ... Require repair or replacement
of linkage.
Linkage binding, not
affecting performance .. 1 ... Suggest repair or replacement
of linkage.

Linkage broken . . .. A ... Require repair or replacement
of linkage.
Linkage loose, affecting
performance . . . A ... Require repair or replacement
of linkage.
Linkage loose, not
affecting performance .. 1 ... Suggest repair or replacement
of linkage.
Linkage missing . . . C . . . Require replacement.
Linkage noisy . . ... 2 .. Suggest repair or replacement.
Missing . . . . . C . . . Require replacement.
Terminal broken . . . A .. Require repair or replacement.
Terminal burned, affecting
performance . . . A . . ... (1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 1 . . ... (1) Suggest repair or
replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 1 .. Suggest repair or replacement.
Terminal loose, affecting
performance . . . B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Missing . . . . . C . . . Require replacement.
Noisy . . . . ... 2 .. Suggest repair or replacement.
Out of adjustment . ... B .. Require repair or replacement.

(1) - Determine cause and correct prior to repair or
replacement of part.
(2) - Inoperative includes intermittent operation or out of OEM
specification.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

ACTUATOR MOTORS (VACUUM)

ACTUATOR MOTOR (VACUUM) INSPECTION

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Condition Code Procedure

Attaching hardware
broken . . . . . A ... Require repair or replacement
of hardware.
Attaching hardware

missing . . . . C . . .. Require replacement of
hardware.
Attaching hardware not
functioning . . . A ... Require repair or replacement
of hardware.
Connector broken . . A .. Require repair or replacement.
Connector (Weatherpack
type) leaking . . .. A .. Require repair or replacement.
Connector melted . . A . . ... (1) Require repair or
replacement.
Connector missing . ... C . . . Require replacement.
Inoperative . . . . A . . (2) Require replacement.
Leaking (vacuum) . . A .. Require repair or replacement.
Linkage bent,
affecting performance .. A ... Require repair or replacement
of linkage.
Linkage bent, not
affecting performance .. 2 ... Suggest repair or replacement
of linkage.
Linkage binding,
affecting performance .. A ... Require repair or replacement
of linkage.
Linkage binding, not
affecting performance .. 1 .. Suggest repair or replacement
of linkage.
Linkage broken . . .. A ... Require repair or replacement
of linkage.
Linkage loose, affecting
performance . . . A ... Require repair or replacement
of linkage.
Linkage loose, not
affecting performance .. 1 ... Suggest repair or replacement
of linkage.
Linkage missing . . . C . . . Require replacement.
Linkage noisy . . ... 2 .. Suggest repair or replacement.
Missing . . . . . C . . . Require replacement.
Noisy . . . . ... 2 .. Suggest repair or replacement.
Out of adjustment . ... A .. Require repair or replacement.

(1) - Determine cause and correct prior to repair or
replacement of part.
(2) - Inoperative includes intermittent operation or out of
OEM specification.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

AIR BAGS