Kia Carnival (2009+). Manual — part 451

Sun Roof Relay Coil

This function defines the condition for switching on or off power feed to sun roof relay coil. This function is available in
RUN position and during after run timer ON.

Power Window Timer

This function defines the conditions for allowing use of power windows, quarter glass, and feed to sunroof relay coil.

Sliding Doors Power Windows

1. Working Conditions

This function is available when ignition key is in RUN position and for 30sec after end of RUN. Window operation
will be canceled if the driver or assist door is opened during the 30sec period after the key is turned from RUN to
ACC or OFF position..

2. Functional Diagram

Power Sliding Door & Power Tailgate

1. Description

There are two sliding doors and one tailgate in the vehicle. A switch is fitted at each B-pillar to permit Power
Sliding Door activation.. For the tailgate, there is also one push button switch. These switches are used to send an
signal of 200 ms minimum to the PSD module (or PTG module).

2. Functional Diagram

Easy Access

1. Description

The easy access function permits automatic rearward movement of the driver seat when the key is removed from
the cylinder. Automatic forward movement of the driver seat will take place when the key is inserted into the
cylinder. This function will be enabled on IMS equipped vehicles when the AUTO button is pressed.
Inhibit Switch should be in P-Position for the Easy Access operation.

2. Functional Diagram

Driver Information

Cluster Indicators

1. The instument cluster indicators listed below are controlled by the In-Panel Module (IPM), Front Area Module

(FAM), or Rear Area Module (RAM) as applicable.
These indicators are:

A. Gearbox status
B. Oil pressure
C. Sediment fuel filter
D. Vacuum
E. Brake fluid

F. Washer fluid

G. Seat belt

H. Park brake

I. Charging voltage

J. Turn indicators

K. High beam

L. Front fog

M. Doors open

N. Tailgate open

O. Stop lamp failure front and rear

2. Functional Diagram

Gearbox Status

The status of the gearbox is sent on the CAN network when the CAN network is available.

Oil Pressure Switch Status

The status of the oil pressure switch is sent on the CAN network when the CAN network is available.

Fuel Filter Status

The FAM receives on digital input the status of the fuel filter (Fuel Filter Input) and sends it (Fuel filter switch) on the
CAN network.

Washer Fluid Sensor Status

The FAM receives on digital input the status of the washer fluid sensor and sends it on the CAN network.
If Washer Fluid Low Input is LOW for more than 10 sec, FAM sends the warning message.

Seat Belt Warning Status

The IPM receives on digital input the status of the seat belt switch and sends the seat belt warning on the CAN
network.
If the Ignition switch status is in RUN or START when the Seat Belt Sw Input is FASTENED, the seat belt warning
indicator is blinking for 6 seconds.
When Seat Belt switch Input is NOT FASTENED, the seat belt warning indicator is blinking for 6 seconds.
If the Seat Belt switch Input is FASTENED during the 6 seconds, the seat belt warning indicator is blinking till the end
of the 6 seconds.
In North America:
the seat belt warning indicator is blinking when Ignition switch is on the status RUN or START and Seat Belt Sw Input
is NOT FASTENED.

Parking Brake Indicator

The indicator manages 3 functions: brake fluid sensor, parking brake warning and vacuum switch.
The vacuum function is available for diesel engine only
The FAM receives on digital input the status of the vacuum switch and the ABS EBD warning and sends them on the
CAN network.
The status of the vacuum switch and the ABS EBD warning are sent on the CAN network when the CAN network is
available.
The FAM receives on digital input the status of the brake fluid sensor and sends it on the CAN network.
The status of the brake fluid sensor is sent on the CAN network when the CAN network is available.
The IPM receives on digital input the status of the parking brake switch and by CAN network the status of the vacuum
switch, the status of the ABS EBD warning, the status of the brake fluid sensor and the speed of the vehicle.

switch, the status of the ABS EBD warning, the status of the brake fluid sensor and the speed of the vehicle.
The IPM sends the park brake indicator control on the CAN network.
The indicator is lighted if the vacuum switch or ABS EBD warning are on or brake fluid sensor is low or park brake
switch is on.
If the speed of the vehicle is over 10 km/h and ignition switch is on the status RUN the park brake indicator control is
blinking at 50% duty in 0.6 second if Parking Brake switch Input is active. In this case Vacuum switch, ABS EBD
warning and Brake Fluid sensor are ignored.
The park brake indicator is blinking on the same time that the chime is ringing. If a CAN signal among Vacuum switch,
EBD warning or Brake Fluid Sens switch is INVALID, out of range or not received this CAN signal is considered to be
OFF.
If VehicleSpeed CAN signal is INVALID or not received, it is considered to be 0 kph.

Charging Voltage Control

The IPM receives on analog input the voltage of generator and sends a warning.
When the voltage of generator L pass strictly above 10V, the state of the CAN variable.

Turn Indicators Status

The status of the turn indicators are sent on the CAN network when the CAN network is available.

High Beam Status

The status of the high beam is sent on the CAN network when the CAN network is available.

Front Fog Lamp Status

The status of the front fog lamp (lightning and state of the bulbs) is sent on the CAN network when the CAN network
is available.

Doors Open Warning

The RAM receives on digital input the status of the driver door open switch and sends it on the CAN network.
The RAM receives on digital input the status of the passenger door open switch and sends it on the CAN network.
The RAM receives on digital input the status of the left sliding door open switch and sends it on the CAN network.
The RAM receives on digital input the status of the right sliding door open switch and sends it on the CAN network.
When vehicle speed is under 10 kph, with ignition key not inserted and any door OPEN, DoorsOpenWngCtrl stays ON
for 20 min and then is turned OFF.

Tailgate Open Switch Status

When vehicle speed is under 10 kph, ignition key is inserted and Tailgate open switch is OPEN, Tailgate Open
warning stays ON forever (IPM can enter sleep mode).
When vehicle speed is under 10 kph, with ignition key not inserted and lgate open switch is OPEN, Tailgate Open
warning stays ON for 20 min and then is turned OFF.

Chime Control

1. The chime warns the driver that a problem is occurred.

These warning are:

A. Seat belt
B. Parking on
C. Over speed
D. Key reminder
E. Light Warning

F. Doors Open

G. Tailgate open warning

2. Chime sound priority:

A. 1st : Seatbelt warning
B. 2nd : Overspeed warning
C. 3rd : Door open warning
D. 4th : T/Gate open warning
E. 5th : Key operated warning

F. 6th : Parking Brake warning