Kia Soul (2020 year). Owner's manual — part 30
Maintenance
58
7
Fuses
Refer to the following table for the
relay type.
Relay Name
Type
PTC HEATER 2 Relay
MICRO
COOLING FAN 2 Relay
MICRO
PDM 3 (IG1) Relay
MICRO
START #1 Relay
MICRO
HEAD LAMP HI Relay
MICRO
PDM 4 (IG2) Relay
MICRO
FUEL PUMP Relay
MICRO
PDM 2 (ACC) Relay
MICRO
COOLING FAN 1 Relay
MINI
BLOWER Relay
MINI
PTC HEATER 1 Relay
MICRO
REAR DEFPGGER Relay
MICRO
POWER OUTLET Relay
MICRO
-------------------------------------------------------------------------------------------------------------------------------------------------------------
59
7
7
Maintenance
Fuses
Battery terminal cover
NOTICE
Not all fuse panel descriptions in this
manual may be applicable to your
vehicle. It is accurate at the time of
printing. When you inspect the fuse
panel in your vehicle, refer to the
fuse panel label.
OSK3078015NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Maintenance
60
7
Light bulbs
Light bulbs
Light bulbs are installed in various
parts of the vehicle to provide light-
ing inside and outside the vehicle as
well as to alert other vehicles.
Bulb replacement precaution
Please keep extra bulbs on hand
with appropriate wattage ratings in
case of emergencies.
Refer to "Bulb wattage" on page 8-
3.
When changing lamps, first turn off
the vehicle at a safe place, firmly
apply the parking brake and detach
the battery's negative (-) terminal.
WARNING
Working on the lights
Prior to working on the light, firmly
apply the parking brake, ensure that
the vehicle start/stop button is in
OFF position and turn off the lights
to avoid sudden movement of the
vehicle and burning your fingers or
receiving an electric shock.
Use only bulbs of the specified
wattage.
CAUTION
Light replacement
Be sure to replace the burned-out
bulb with one of the same wattage
rating. Otherwise, it may cause
damage to the fuse or electric wir-
ing system.
CAUTION
Headlamp Lens
To prevent damage, do not clean the
headlamp lens with chemical sol-
vents or strong detergents.
NOTICE
䳜 If the light bulb or lamp connector
is removed while the lamp is still
on, the fuse box's electronic sys-
tem may log it as a malfunction.
Therefore, a lamp malfunction
incident may be recorded as a
Diagnostic Trouble Code (DTC) in
the fuse box.
䳜 It is normal for an operating lamp
to flicker momentarily. This is due
to a stabilization function of the
vehicle's electronic control device.
If the lamp lights up normally
after momentarily blinking, then
it is functioning as normal.
However, if the lamp continues to
flicker several times or turns off
completely, there may be an error
in the vehicle's electronic control
device. Please have the vehicle
checked by an authorized Kia
dealer immediately.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
61
7
7
Maintenance
Light bulbs
NOTICE
We recommend that the headlight
aiming be adjusted by an authorized
Kia dealer after an accident or after
the headlight assembly is rein-
stalled.
NOTICE
After driving in heavy rain or wash-
ing, headlamp and taillamp lenses
could appear frosty. This condition
is caused by the temperature dif-
ference between the lamp inside
and outside. This is similar to the
condensation on your windows
inside your vehicle during the rain
and doesn't indicate a problem with
your vehicle. If the water leaks into
the lamp bulb circuitry, we recom-
mend that you have the vehicle
checked by an authorized Kia dealer.
If you don't have the necessary
tools, the correct bulbs and the
expertise, consult an authorized Kia
dealer. In many cases, it is difficult
to replace vehicle light bulbs
because other parts of the vehicle
must be removed before you can
get to the bulb. This is especially
true if you have to remove the
headlamp assembly to get to the
bulb(s).
Removing/installing the headlamp
assembly can result in damage to
the vehicle. If non-genuine parts or
substandard bulbs are used, it may
lead to blowing a fuse or other wir-
ing damages.
Do not install extra lamps or LEDs to
the vehicle. If additional lights are
installed, it may lead to lamp mal-
functions and flickering. Addition-
ally, the fuse box and other writing
may be damaged.
Light bulb position (Front)
Head lamp - Type A
Head lamp - Type B
OSK3078016NR
OSK3078017NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Maintenance
62
7
Light bulbs
Head lamp 䳍 Type C
Fog lamp
1. Front turn signal lamp (Bulb Type)
2. Headlamp (Low/High)
3. Position lamp/Daytime running
lamp (Bulb Type)
4. Side marker (Bulb/LED Type)
5. Front turn signal lamp (LED Type)
6. Headlamp (LED) (Sub Low)
7. Headlamp (LED) (Low)
8. Position lamp/Daytime running
lamp (LED Type)
9. Front fog lamp (LED Type)
10.Front fog lamp (Bulb Type)
Light bulb position (Rear)
Rear combination lamp - Type A
Rear combination lamp - Type B
License plate lamp
OSK3078018NR
OSK3078019NR
OSK3078020NR
OSK3078021NR
OSK3078038NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
63
7
7
Maintenance
Light bulbs
High mounted stop lamp
1. Tail lamp (Bulb type)
2. Tail and stop lamp (Bulb type)
3. Rear turn signal lamp (Bulb type)
4. Back-up lamp (Bulb type)
5. Side marker (Bulb/LED Type)
6. Tail lamp (LED type)
7. Stop lamp (LED type)
8. License plate lamp (Bulb type)
9. High mounted stop lamp (Bulb or
LED type)
Light bulb position (Side)
1. Side repeater lamp (LED type)
Headlamp bulb
WARNING
Halogen bulbs
Handle halogen bulbs with care.
䳜 Halogen bulbs contain pressurized
gas that will produce flying pieces
of glass if broken.
䳜 Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact
with liquids. Never touch the glass
with bare hands. Residual oil may
cause the bulb to overheat and
burst when lit. A bulb should be
operated only when installed in a
headlamp.
䳜 If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
䳜 Wear eye protection when chang-
ing a bulb. Allow the bulb to cool
down before handling it.
OSK3078022NR
OSK3078027NR
OSK3078081NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Maintenance
64
7
Light bulbs
Replacing Headlamp (High/Low
beam) bulb (Headlamp Type A,B)
If the Headlamp (High/Low) (1) does
not operate, have the vehicle
checked by an authorized Kia dealer.
Type A / Type B
Replacing Position lamp/DRL/Front
turn signal lamp bulb (Type A, B)
Type A
Type B
1. Open the hood.
2. Remove the bulb socket-connec-
tor by turning it counterclockwise.
3. Remove the bulb from the lamp
assembly.
4. Install a new bulb.
5. Connect the bulb socket-connec-
tor.
Position lamp / Day time running
lamp (LED type) replacement
(Headlamp Type B)
If the position lamp + DRL (LED) (1)
does not operate, have the vehicle
checked by an authorized Kia dealer.
OSK3078040NR
OSK3078041NR
OSK3078065NR
OSK3078023NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
65
7
7
Maintenance
Light bulbs
The LED lamps cannot be replaced
as a single component because it is
an integrated unit. The LED lamps
have to be replaced with the unit. A
skilled technician should check or
repair the position lamp + DRL (LED),
for it may damage related parts of
the vehicle.
Replacing Headlamp (LED type)
(Headlamp Type C)
If the Low/High beam lamp, Day
time running lamp/Position lamp
does not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single component because it is
an integrated unit. The LED lamps
have to be replaced with the unit.
A skilled technician should check or
repair the head lamp (LED), for it
may damage related parts of the
vehicle.
Replacing front fog lamp bulb (if
equipped)
If the front fog lamp (1) does not
operate, have the vehicle checked by
an authorized Kia dealer.
Type A
Type B
Replacing side repeater lamp (LED
type) bulb
If the side repeater lamp (LED), does
not operate, have the vehicle
checked by an authorized Kia dealer.
OSK3078024NR
OSK3078026NR
OSK3078066NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Maintenance
66
7
Light bulbs
The LED lamps cannot be replaced
as a single component because it is
an integrated unit. The LED lamps
have to be replaced with the unit.
A skilled technician should check or
repair the side repeater lamp (LED),
for it may damage related parts of
the vehicle.
Replacing stop/tail and turn signal
lamp (bulb type) bulb (Rear combi-
nation lamp Type A)
1. Open the liftgate.
2. Loosen the lamp assembly retain-
ing screws with a screwdriver.
3. Remove the rear combination
lamp assembly from the body of
the vehicle.
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket.
6. Insert a new bulb by inserting it
into the socket and rotating it
until it locks into place.
7. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly and
turning the socket clockwise.
8. Reinstall the lamp assembly to
the body of the vehicle.
OSK3078027NR
OSK3078054NR
OSK3078033NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
67
7
7
Maintenance
Light bulbs
Replacing tail/back-up lamp bulb
(Rear combination lamp Type A)
1. Open the liftgate.
2. Remove the service cover assem-
bly to the body of the vehicle.
(Loosen the lamp assembly
retaining screws and remove the
lamp assembly from the body of
the vehicle for back-up lamp)
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
Tail lamp
Back-up lamp
4. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
5. Insert a new bulb by inserting it
into the socket and rotating it
until it locks into place.
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assem-
bly and turn the socket clockwise.
7. Install the service cover by putting
it into the service hole.
Replacing stop and tail lamp (LED
type) bulb (Rear combination lamp
Type B)
If the stop and tail lamp (LED)
(1,2),does not operate, have the
vehicle checked by an authorized Kia
dealer.
OSK3078083NR
OSK3078055NR
OSK3078090NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Maintenance
68
7
Light bulbs
The LED lamps cannot be replaced
as a single component because it is
an integrated unit. The LED lamps
have to be replaced with the unit.
A skilled technician should check or
repair the stop and tail lamp (LED),
for it may damage related parts of
the vehicle.
Replacing high mounted stop lamp
(LED type) bulb
If the high mounted stop lamp (LED)
(1), does not operate, have the vehi-
cle checked by an authorized Kia
dealer.
The LED lamps cannot be replaced
as a single component because it is
an integrated unit. The LED lamps
have to be replaced with the unit.
A skilled technician should check or
repair the high mounted stop lamp
(LED), for it may damage related
parts of the vehicle.
Replacing high mounted stop lamp
(bulb type) bulb
1. Open the liftgate.
2. Remove the cover.
3. Loosen the retaining bolts and
remove the hose (1).
OSK3078028NR
OSK3078029NR
OSK3078056NR
OSK3078057NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
69
7
7
Maintenance
Light bulbs
4. Pull out the bulb-socket from the
high mounted stop lamp assem-
bly using the driver.
5. Replace the bulbs by pulling it out
from the socket.
6. Reinstall in the reverse order.
Replacing license plate lamp bulb
1. Remove the lamp assembly by
using a flat-blade screwdriver.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Remove the bulb from bulb-
socket by pulling it out.
4. Insert a new bulb by inserting it
into the bulb-socket.
5. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assem-
bly and turn the socket clockwise.
6. Install the lamp assembly to the
body of the vehicle.
OSK3078058NR
OSK3078059NR
OSK3078036NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Maintenance
70
7
Light bulbs
Replacing map lamp (bulb type)
bulb
1. Using a flat-blade screwdriver,
gently pry the lens cover from
lamp housing.
2. Remove the bulb by pulling it
straight out.
3. Install a new bulb in the socket.
4. Align the lens cover tabs with the
lamp housing notches and snap
the lens into place.
NOTICE
Be careful not to dirty or damage
the lens, lens tab, and plastic hous-
ings.
Replacing map lamp (LED type)
bulb
If the map lamp (LED) does not
operate, have the vehicle checked by
an authorized Kia dealer.
The LED lamps cannot be replaced
as a single component because they
are part of an integrated unit. The
LED lamps have to be replaced with
the unit.
A skilled technician should check or
repair the map lamp (LED), for it
may damage related parts of the
vehicle.
Replacing vanity mirror lamp bulb
OSK3078084NR
OSK3078085NR
ODEEV098065NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
71
7
7
Maintenance
Light bulbs
WARNING
Interior lamps
Prior to working on the Interior
lamps, ensure that the "OFF" button
is depressed to avoid burning your
fingers or receiving an electric
shock.
1. Using a flat-blade screwdriver,
gently pry the lamp assembly
from interior.
2. Remove the bulb by pulling it
straight out.
3. Install a new bulb in the socket.
4. Install the lamp assembly to inte-
rior.
NOTICE
Be careful not to dirty or damage
the lens, lens tab, and plastic hous-
ings.
Replacing room lamp (bulb type)
bulb
WARNING
Interior lamps
Prior to working on the Interior
lamps, ensure that the "OFF" button
is depressed to avoid burning your
fingers or receiving an electric
shock.
1. Using a flat-blade screwdriver,
gently pry the lens cover from
lamp housing.
2. Remove the bulb by pulling it
straight out.
3. Install a new bulb in the socket.
4. Align the lens cover tabs with the
lamp housing notches and snap
the lens into place.
NOTICE
Be careful not to dirty or damage
the ODE076049 lens, lens tab, and
plastic housings.
Replacing room lamp (LED type)
bulb
If the Room lamp (LED) does not
operate, have the vehicle checked by
an authorized Kia dealer.
ODEEV098066NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Maintenance
72
7
Light bulbs
The LED lamps cannot be replaced
as a single component because they
are part of an integrated unit. The
LED lamps have to be replaced with
the unit.
A skilled technician should check or
repair the Room lamp (LED), for it
may damage related parts of the
vehicle.
Replacing glove box lamp
1. Using a flat-blade screwdriver,
gently pry the lamp assembly
from interior.
2. Remove the bulb by pulling it
straight out.
3. Install a new bulb in the socket.
4. Install the lamp assembly to inte-
rior.
CAUTION
Be careful not to dirty or damage
the lens, lens tab, and plastic hous-
ings.
Replacing liftgate room lamp bulb
1. Using a flat-blade screwdriver,
gently pry the lens cover from
lamp housing.
2. Remove the bulb by pulling it
straight out.
3. Install a new bulb in the socket.
4. Align the lens cover tabs with the
lamp housing notches and snap
the lens into place.
If the Liftgate room lamp (LED) does
not operate, have the vehicle
checked by an authorized Kia dealer.
ODEEV098067NR
OSK3078044NR
OSK3078045NR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
73
7
7
Maintenance
Appearance care
The LED lamps cannot be replaced
as a single component because they
are part of an integrated unit. The
LED lamps have to be replaced with
the unit.
A skilled technician should check or
repair the Liftgate room lamp (LED),
for it may damage related parts of
the vehicle.
NOTICE
Be careful not to dirty or damage
the lens, lens tab, and plastic hous-
ings.
Appearance care
Use the information in the following
sections to keep the exterior and
interior of your vehicle clean.
Exterior care
Use the information in the following
sections to maintain the exterior of
your vehicle. Keeping the exterior
clean is not only aesthetically pleas-
ing, but it also helps to prolong the
life of the vehicle.
Exterior general caution
It is very important to follow the
label directions when using any
chemical cleaner or polish. Read all
warning and caution statements
that appear on the label.
Finish maintenance
Washing
To help protect your vehicle's finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for off-road
driving, you should wash it after
each off-road trip. Pay special
attention to the removal of any
accumulation of salt, dirt, mud, and
other foreign materials. Make sure
the drain holes in the lower edges of
the doors and rocker panels are
kept clear and clean.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст