Suzuki Grand Vitara JB627. Manual — part 94

1D-57 Engine Mechanical:

2) Install piston pin to piston and connecting rod:

After applying engine oil to piston pin and piston pin
holes in piston (1) and connecting rod (3), fit
connecting rod to piston as shown in figure and
insert piston pin to piston and connecting rod, and
install piston pin circlips.

NOTE
“59J0” mark on connecting rod must face
toward crankshaft pulley side.

NOTE

• Install circlip (6) with its cut part facing as

shown in figure.

• Install so that circlip end gap comes within

such range as indicated by arrow.

3) Install piston rings to piston:

• As shown in figure, 1st (1) and 2nd rings (2) have

“RN” or “R” mark respectively. When installing
these piston rings to piston, direct marked side of
each ring toward top of piston.

• 1st rings differs from 2nd ring in thickness, shape

of surface contacting cylinder wall.
Distinguish 1st ring from 2nd ring by referring to
figure.

• When installing oil ring (3), install spacer first and

then 2 rails.

4) After installing three rings (1st, 2nd and oil rings),

distribute their end gaps as shown in figure.

2. Arrow mark

1. Piston

4. Oil hole

2. Arrow mark

5. Crankshaft pulley side

3. Connecting rod

1

2

3

I6JB01140093-01

1

2

3

6

4

5

I6JB01140094-02

1. Mark
2. 1st ring end gap
3. 2nd ring end gap and oil ring spacer gap
4. Oil ring upper rail gap
5. Oil ring lower rail gap

I6JB01140095-01

I6JB01140096-01

Engine Mechanical: 1D-58

Cylinders, Pistons and Piston Rings Inspection

S6JB0B1406040

NOTE
Before the following inspection, clean carbon
from piston head and ring grooves, using a
suitable tool.

Cylinders
• Inspect cylinder walls for scratches, roughness, or

ridges which indicate excessive wear. If cylinder bore
is very rough or deeply scratched, or ridged, rebore
cylinder and use over size piston.

• Using a cylinder gauge, measure cylinder bore in

thrust and axial directions at 2 positions (1, 2) as
shown in figure. If any of the following condition is
noted, rebore cylinder.
– Cylinder bore via. exceeds limit.
– Difference of measurements at 2 positions exceeds

taper limit.

– Difference between thrust and axial measurements

exceeds out-of-round limit.

Cylinder bore
Standard: 88.000 – 88.020 mm (3.4646 – 3.4653
in.)
Limit: 88.050 mm (3.4665 in.)

Taper and out-of-round
Limit: 0.10 mm (0.004 in.)

NOTE
If any one of six cylinders has to be rebored,
rebore all six to the same oversize. This is
necessary for the sake of uniformity and
balance.

Pistons
• Inspect piston for faults, cracks or other damages.

Damaged or faulty piston should be replaced.

• Piston diameter:

As shown in figure, piston diameter should be
measured at a position 26.5 mm (1.04 in.) (“a”) from
piston skirt end in the direction perpendicular to piston
pin.

Piston diameter
Standard: 87.970 – 87.990 mm (3.4634 – 3.4641 in.)
Oversize (0.50 mm): 88.470 – 88.490 mm (3.4831 –
3.4838 in.)

• Piston clearance:

Measure cylinder bore diameter and piston diameter
to find their difference which is piston clearance.
Piston clearance should be within specification as
given below. If it is out of specification, rebore cylinder
and use oversize piston.

Piston-to-cylinder clearance
0.02 – 0.04 mm (0.0008 – 0.0015 in.)

NOTE
Cylinder bore diameter should be measured
in 2 places 90 degrees apart.

1. 50 mm (1.96 in.)

2. 95 mm (3.74 in.)

I5JA01140018-01

“a”: 26.5 mm (1.04 in.)

“a”: 26.5 mm (1.04 in.)

IYSQ01141121-01

I5JA01140019-01

1D-59 Engine Mechanical:

• Ring groove clearance:

Before checking, piston grooves must be clean, dry
and free of carbon.
Fit new piston ring (1) into piston groove, and
measure clearance between ring and ring land by
using thickness gauge (2). If clearance is out of
specification, replace piston.

Ring groove clearance
Top: 0.03 – 0.07 mm (0.0012 – 0.0027 in.)
2nd: 0.02 – 0.06 mm (0.0008 – 0.0023 in.)

Piston Rings
To measure end gap, insert piston ring into cylinder bore
and then measure the gap by using thickness gauge.
If measure gap is out of specification, replace ring.

NOTE
Clean carbon and any other dirt from top of
cylinder bore before inserting piston ring.

Piston ring end gap

Piston Pins and Connecting Rods Inspection

S6JB0B1406041

Piston Pins
• Check piston pin, connecting rod small end bore and

piston bore for wear or damage, paying particular
attention to condition of small end bore bush. If pin,
connecting rod small end bore or piston bore is badly
worn or damaged, replace pin, connecting rod or
piston.

• Piston pin clearance:

Check piston pin clearance in small end. Replace
connecting rod if its small end is badly worn or
damaged or if measured clearance exceeds limit.

Piston pin clearance in small end
0.003 – 0.014 mm (0.0001 – 0.0005 in.)

Small-end bore
21.003 – 21.011 mm (0.8269 – 0.8272 in.)

Piston pin diameter
20.997 – 21.000 mm (0.82665 – 0.82677 in.)

Connecting Rods
• Big-end side clearance:

Check big-end of connecting rod for side clearance,
with rod fitted and connected to its crank pin in the
normal manner. If measured clearance is found to
exceed its limit, replace connecting rod.

Big-end side clearance
Standard: 0.25 – 0.35 mm (0.0099 – 0.0137 in.)
Limit: 0.45 mm (0.0177 in.)

Item

Standard

Limit

Top ring

0.20 – 0.35 mm

(0.0079 – 0.0137 in.)

0.7 mm

(0.0276 in.)

2nd ring

0.35 – 0.47 mm

(0.0138 – 0.0185 in.)

0.7 mm

(0.0276 in.)

Oil ring

0.20 – 0.70 mm

(0.0079 – 0.0275 in.)

1.8 mm

(0.0709 in.)

1. Cylinder block

3. Piston ring

2. Feeler gauge

4. 120 mm (4.72 in.)

I2RH01140159-01

IYSQ01141124-01

I5JA01140020-01

I6JB01140097-01

Engine Mechanical: 1D-60

• Connecting rod alignment:

Mount connecting rod on aligner to check it for bow
and twist. If limit is exceeded, replace it.

Connecting rod alignment
Limit on bow: 0.05 mm (0.0020 in.)
Limit on twist: 0.10 mm (0.0039 in.)

Crank Pins and Connecting Rod Bearings
Inspection

S6JB0B1406042

• Inspect crank pin for uneven wear or damage.

Measure crank pin for out-of-round or taper with a
micrometer. If crank pin is damaged, or out-of-round
or taper is out of limit, replace crankshaft or regrind
crank pin then inspect rod bearing clearance referring
to “Connecting rod bearing clearance”.

Crank pin diameter

Crank pin out-of-round (a – b)
Limit: 0.01 mm (0.0004 in.)

Crank pin taper (c – d)
Limit: 0.01 mm (0.0004 in.)

Connecting rod bearing general information:

Service connecting rod bearings are available in
standard size and 0.25 mm (0.0098 in.) undersize,
and standard size bearing has 5 kinds of bearings
differing in tolerance. For identification of undersize
bearing, it is painted red at the position as indicated in
figure, undersize bearing thickness is 1.605 – 1.615
mm (0.0632 – 0.0635 in.) at the center of it.

Connecting rod bearing visual inspection:

Inspect bearing shells for signs of fusion, pitting, burn
or flaking and observe contact pattern. Bearing shells
found in defective condition must be replaced.

Connecting rod bearing clearance:

a. Before checking bearing clearance, clean bearing

and crank pin.

b. Install bearing in connecting rod and bearing cap.
c. Place a piece of gaging plastic (1) to full width of

crank pin as contacted by bearing (parallel to
crankshaft), avoiding oil hole.

d. Install rod bearing cap to connecting rod referring

to “Pistons, Piston Rings, Connecting Rods and
Cylinders Removal and Installation”.

NOTE
Do not turn crankshaft with gaging plastic
installed.

Connecting rod

bearing size

Crank pin diameter

Standard

49.982 – 50.000 mm
(1.9678 – 1.9685 in.)

0.25 mm (0.0098 in.)

undersize

49.732 – 49.750 mm
(1.9580 – 1.9586 in.)

IYSQ01143136-01

1. Painting

IYSQ01141169-01

I6JB01140098-01

Была ли эта страница вам полезна?
Да!Нет
2 посетителя считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности