Suzuki Grand Vitara JB627. Manual — part 35
1A-89 Engine General Information and Diagnosis:
DTC P0133 / P2A00: O2 Sensor Circuit Slow Response / Performance (Sensor-1, Bank-1)
S6JB0B1104026
Wiring Diagram
A/F Sensor Description
Refer to “A/F Sensor Description”
DTC Detecting Condition and Trouble Area
5
TP sensor check
1) Check TP sensor for performance referring to “Electric
Throttle Body Assembly On-Vehicle Inspection in
Section 1C”.
Is it in good condition?
Substitute a known
good ECM and recheck.
Replace electric throttle
body assembly.
Step
Action
Yes
No
4
3
9
PNK
6
2
1
d
a
8
5
BLK/WHT
BLK
PNK
GRN
C37-16
C37-77
C37-19
C37-18
BLK
BLK
BLU
WHT
C37-17
C37-79
BLK
WHT
RED/YEL
RED/BLU
PNK/BLK
BLK/YEL
10
7
11
5 V
5 V
1
3 2
4
5
6
7
8
9
1110
12
13
14
15
16
17
18
19
20
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
33
34
35
36
37
38
39
40
32
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
c
b
I6JB01110006-01
a. Signal (+) circuit of A/F sensor (bank-1)
1. HO2S heater relay
5. IG COIL fuse
9. ECM
b. Signal (–) circuit of A/F sensor (bank-1)
2. Shield wire
6. A/F sensor
10. Adjusting resistor (if equipped)
c. Adjusting resistor (+) circuit of A/F sensor (bank-1)
3. Ignition Switch
7. A/F sensor heater
11. A/F sensor element
d. Adjusting resistor (–) circuit of A/F sensor (bank-1)
4. O2 HTR fuse
8. To A/F sensor (bank-2),
HO2S (bank-1 and -2)
DTC detecting condition
Trouble area
DTC P0133 O2 Sensor Circuit Slow Response (Sensor-1, Bank-1):
Number of shifting times for A/F sensor signal between rich and lean is
less than 13 times in 20 sec. while A/F (fuel trim) is shifted rich to lean and
lean to rich with specified diagnosis frequency under specified running.
(2 driving cycle detection logic, monitoring once per driving cycle)
DTC P2A00 O2 Sensor Circuit performance (Sensor-1, Bank-1):
Amplitude index of A/F sensor signal between rich and lean is more than
1.3 or less than 0.7 while A/F (fuel trim) is shifted rich to lean and lean to
rich with specified diagnosis frequency under specified running.
(2 driving cycle detection logic, monitoring once per driving cycle)
• A/F sensor circuit
• A/F sensor
• ECM
Engine General Information and Diagnosis: 1A-90
DTC Confirmation Procedure
WARNING
!
• When performing a road test, select a place where there is no traffic or possibility of a traffic
accident and be very careful during testing to avoid occurrence of an accident.
• Road test should be carried out by 2 persons, a driver and a tester, on a level road.
NOTE
Check to make sure that following conditions are satisfied when using this “DTC Confirmation
Procedure”.
• Intake air temperature: –14
°C (7 °F) to 70 °C (158 °F).
• Engine coolant temperature: 40
°C (104 °F) or more.
• The following DTC is not detected (When DTC P0133 is detected): A/F sensor heater.
1) With ignition switch turned OFF, connect scan tool.
2) Turn ON ignition switch and clear DTC using scan tool.
3) Start engine and warm up to normal operating temperature.
4) Drive vehicle at 40 mph (60 km/h) or higher. (engine speed: 2500 – 3000 r/min.)
5) Keep above vehicle speed for 6 min. or more. (Throttle valve opening is kept constant in this step.)
6) Release accelerator pedal and with engine brake applied, keep vehicle coasting (with fuel cut for 3 sec. or more)
and then stop vehicle.
7) Check if DTC and pending DTC exist by using scan tool. If not, check if oxygen sensor monitoring test has been
completed by using scan tool. If not in both of above checks (i.e., no DTC and pending DTC and oxygen sensor
monitoring test not completed), check vehicle condition (environmental) and repeat Step 3) through 6).
DTC Troubleshooting
NOTE
Before this trouble shooting is performed, read the precautions for DTC troubleshooting referring to
“Precautions for DTC Troubleshooting”.
Step
Action
Yes
No
1
Was “Engine and Emission Control System Check”
performed?
Go to Step 2.
Go to “Engine and
Emission Control
System Check”.
2
DTC check
Is there DTC P0134?
Go to applicable DTC.
Go to Step 3.
3
DTC check
Is there DTC(s) other than P0133, P0134 and P2A00?
Go to applicable
DTC(s).
Go to Step 4.
4
Intake system and exhaust system for leakage check
1) Check intake system and exhaust system for leakage.
Is it in good condition?
Go to Step 5.
Repair or replace
defective parts.
1A-91 Engine General Information and Diagnosis:
DTC P0134: O2 Sensor Circuit No Activity (Sensor-1, Bank-1)
S6JB0B1104027
A/F Sensor Description
Refer to “A/F Sensor Description”
5
A/F sensor circuit check
1) Disconnect connector from A/F sensor (bank-1) with
ignition switch turned OFF.
2) Check for proper terminal connection to A/F sensor
(bank-1) connector.
3) If connections are OK, check that A/F sensor (bank-1)
circuit is as follows.
• Wiring harness resistance of each “Signal (+) circuit of
A/F sensor (bank-1)”, “Signal (–) circuit of A/F sensor
(bank-1)”, “Adjusting resistor (+) circuit of A/F sensor
(bank-1)” and “Adjusting resistor (–) circuit of A/F
sensor (bank-1)” is less than 1
Ω.
Is it in good condition?
Replace A/F sensor
(bank-1).
Repair or replace
defective wiring
harness.
Step
Action
Yes
No
4
3
9
PNK
6
2
1
d
a
b
8
5
BLK/WHT
BLK
PNK
GRN
C37-16
C37-77
C37-19
C37-18
BLK
BLK
BLU
WHT
C37-17
C37-79
BLK
WHT
RED/YEL
RED/BLU
PNK/BLK
BLK/YEL
10
7
11
5 V
5 V
1
3 2
4
5
6
7
8
9
1110
12
13
14
15
16
17
18
19
20
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
33
34
35
36
37
38
39
40
32
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
c
I6JB01110054-01
a. Signal (+) circuit of A/F sensor (bank-1)
1. HO2S heater relay
5. IG COIL fuse
9. ECM
b. Signal (–) circuit of A/F sensor (bank-1)
2. Shield wire
6. A/F sensor
10. Adjusting resistor (if
equipped)
c. Control circuit of A/F sensor (bank-1) heater
3. Ignition Switch
7. A/F sensor heater
11. A/F sensor element
d. Control ground circuit of A/F sensor (bank-1) heater
4. O2 HTR fuse
8. To A/F sensor (bank-2), HO2S
(bank-1 and -2) (if equipped)
Engine General Information and Diagnosis: 1A-92
DTC Detecting Condition and Trouble Area
DTC Confirmation Procedure
NOTE
Check to make sure that following conditions are satisfied when using this “DTC Confirmation
Procedure”.
• Engine coolant temperature: higher than –10
°C (14 °F).
• The following DTCs are not detected: ECT sensor, MAF sensor, A/F sensor heater and IAT sensor.
1) With ignition switch OFF, connect scan tool to DLC.
2) Turn ON ignition switch and clear DTC.
3) Start engine and warm up to normal operating temperature.
4) Run engine at idle speed for 1 min. or more.
5) Check DTC and pending DTC.
DTC Troubleshooting
NOTE
Before this trouble shooting is performed, read the precautions for DTC troubleshooting referring to
“Precautions for DTC Troubleshooting”.
DTC detecting condition
Trouble area
Impedance of A/F sensor element is higher than 67
Ω for more than 20 sec.
even though A/F sensor heater is turned ON for more than specified time
with engine running.
(2 driving cycle detection logic)
• A/F sensor circuit
• A/F sensor
• ECM
Step
Action
Yes
No
1
Was “Engine and Emission Control System Check”
performed?
Go to Step 2.
Go to “Engine and
Emission Control
System Check”.
2
A/F sensor signal check
1) Connect scan tool with ignition switch turned OFF.
2) Warm up engine to normal operating temperature and
keep it at 2000 r/min. for 60 sec.
3) Repeat racing engine (Repeat depressing accelerator
pedal 5 to 6 times continuously to enrich A/F mixture and
take foot off from pedal to enlean it).
4) Check for A/F sensor (bank-1) output current displayed
on scan tool.
Does A/F sensor output current between –0.2 mA and 0.2
mA?
Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection in Section
00”.
Go to Step 3.
3
A/F sensor circuit check
1) Disconnect connector from A/F sensor (bank-1) with
ignition switch turned OFF.
2) Check for proper terminal connection to A/F sensor
(bank-1) connector.
3) If connections are OK, check that A/F sensor circuit is as
follows.
• Wiring harness resistance of each “Signal (+) circuit of
A/F sensor (bank-1)”, “Signal (–) circuit of A/F sensor
(bank-1)”, “Control circuit of A/F sensor (bank-1)
heater” and “Control ground circuit of A/F sensor
(bank-1) heater” is less than 1
Ω.
Are they in good condition?
Go to Step 4.
repair or replace
defective wiring
harness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст