Suzuki Grand Vitara JB627. Manual — part 144
3B-18 Differential: Front
Front Differential Inspection
S6JB0B3216006
• Check companion flange for wear or damage.
• Check bearings for wear or discoloration.
• Check differential carrier for cracks.
• Check drive bevel pinion and drive bevel gear for
wear or cracks.
• Check differential gears, pinions and pinion shafts for
wear or damage.
• Check differential gear spline for wear or damage.
Specifications
Tightening Torque Specifications
S6JB0B3217001
NOTE
The specified tightening torque is also described in the following.
“Front Differential Unit Components: Front”
“Front Differential Components: Front”
Reference:
For the tightening torque of fastener not specified in this section, refer to “Fastener Information in Section 0A”.
Special Tools and Equipment
Recommended Service Material
S6JB0B3218001
NOTE
Required service material is also described in the following.
“Front Differential Components: Front”
Fastening part
Tightening torque
Note
N
⋅m
kgf-m
lb-ft
Differential oil drain plug
23
2.3
17.0
Differential oil level / filler plug
23
2.3
17.0
Bevel gear bolt
Tighten 40 N
⋅m (4.0 kgf-m, 29.5 lb-ft) + 50° )
Rear cover bolt No.1
50
5.0
36.5
Rear cover bolt No.2
60
6.0
43.5
Retainer bolt
50
5.0
36.5
Rear mounting bracket bolt
50
5.0
36.5
Right mounting bracket bolt
50
5.0
36.5
Material
SUZUKI recommended product or Specification
Note
Grease
SUZUKI Super Grease A
P/No.: 99000–25010
Sealant
SUZUKI Bond No.1217G
P/No.: 99000–31260
Thread lock cement
Thread Lock Cement Super 1322
P/No.: 99000–32110
Differential: Front 3B-19
Special Tool
S6JB0B3218002
09900–20607
09900–20701
Dial gauge
Magnetic stand
09913–50121
09913–65135
Oil seal remover
Bearing puller
09913–75510
09913–75520
Bearing installer
Bearing installer
09913–75821
09913–85210
Bearing installer attachment
Bearing installer
09922–66021
09922–75222
Flange holder
Differential gear preload
adjuster
09922–76520
09924–74510
Bevel pinion gauge block
Bearing and oil seal handle
09924–84510–004
09924–84510–005
Bearing installer attachment
Bearing installer attachment
(D)
3B-20 Differential: Front
09925–14520
09925–86010
Bearing and oil seal installer
(80 x 50 mm)
Bearing puller attachment
09925–88210
09926–78311
Bearing puller attachment
Differential bevel pinion
dummy
09926–78311–002
09926–78320
Pinion mounting dummy
Mounting dummy
09928–06510
09930–30104
Differential torque checking
tool
Sliding shaft
09940–53111
09941–64511
Differential side bearing
installer
Bearing and oil seal remover
(30 mm Min.)
09951–16070
09951–16090
Shim adjuster attachment
Oil seal installer
09951–18210
09951–46010
Oil seal remover & installer
No. 2
Drive shaft oil seal installer
Differential: Rear 3B-21
Rear
General Description
Rear Differential Construction
S6JB0B3221001
Refer to “Front Differential Construction: Front”.
Diagnostic Information and Procedures
Rear Differential Symptom Diagnosis
S6JB0B3224001
Refer to “Front Differential Symptom Diagnosis: Front”.
Repair Instructions
Rear Differential Oil Change
S6JB0B3226001
Refer to “Front Differential Oil Change: Front” except for oil capacity below that is different from the front differential.
Rear differential oil capacity
Reference: 0.75 – 0.85 liters (1.6/1.3 – 1.8/1.5 US/Imp. pt.)
Rear Differential Unit Components
S6JB0B3226002
(a)
4
(a)
3
(b)
5
1
2
I5JB0A322002-03
1. Rear differential
4. Front mounting bracket bolt
2. Front mounting bracket
: 120 N
⋅m (12.0 kgf-m, 87.0 lb-ft)
3. Rear mounting bolt
: 50 N
⋅m (5.0 kgf-m, 36.5 lb-ft)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст