Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 503
9E-23 Glass / Windows / Mirrors:
Power Door Mirror Actuator Inspection
S6JB0A9506021
1) Remove door trim referring to step 1) to 3) of “Front
Door Glass Removal and Installation”.
2) Disconnect door mirror coupler (1).
3) Check that door mirror operates properly when
battery voltage is applied to connector terminals.
4) Connect battery positive (+) and negative (–)
terminal to the door mirror terminals as shown.
If it does not follow the table’s operation, replace
door mirror assembly.
Door Mirror Heater Inspection (If Equipped)
S6JB0A9506022
1) Remove door trim referring to step 1) to 3) of “Front
Door Glass Removal and Installation”.
2) Disconnect door mirror connector (1).
3) Check for continuity between terminals “a” and “b”.
If no continuity, replace outside mirror.
Door Mirror Heater Relay Inspection (If
Equipped)
S6JB0A9506023
1) Disconnect negative (–) cable from battery.
2) Remove door mirror heater relay (included in
integration relay) (1) from main fuse box (2).
B
C
A
Operation
Terminal
Up
Down
Left
Right
C
B
A
I5JB0A950040-01
“a”
“b”
I5JB0A950041-01
2
1
I5JB0A950031-01
Glass / Windows / Mirrors: 9E-24
3) Check that there is no continuity between terminals
“a” and “b”.
If there is continuity, replace relay.
4) Check that there is continuity between terminals “a”
and “b” when a 12 V battery is connected to terminal
“a” and “c”.
If malfunction is found, replace integration relay.
Special Tools and Equipment
Recommended Service Material
S6JB0A9508001
NOTE
Required service material is also described in the following.
“Front Door Window Components”
“Rear Door Window Components”
“a”
“c”
“b”
“a”
“c”
“b”
I5JB0A950042-02
Material
SUZUKI recommended product or Specification
Note
Grease
SUZUKI Super Grease A
P/No.: 99000–25011
9F-1 Security and Locks:
Body, Cab and Accessories
Security and Locks
General Description
Key Coding Construction
S6JB0A9601001
Key Usage and Identification
Key is used for ignition and door lock cylinders. Key is cut on both edges to make them reversible.
Key identification is obtained from five character key code stamped on key code tag. Using this key code, key code
cutting combination can be determined from a code list (available to owners of key cutting equipment from suppliers).
Component Location
Power Door Lock and Keyless Entry System Component Location
S6JB0A9603001
3
4
5
7
6
8
8
1
I5JB0A960001-03
1. Keyless entry receiver
3. Power door lock switch
5. Rear door actuator (5 door model only)
7. Door switch
2. Transmitter
4. Front door actuator
6. Rear end door actuator
8. BCM
Security and Locks: 9F-2
Diagnostic Information and Procedures
Power Door Lock System Symptom Diagnosis
S6JB0A9604001
NOTE
• Use of SUZUKI scan tool makes it easy to check whether a faulty condition is on the input side or
output side of BCM. For checking procedure, refer to “Diagnosis Using Output Test Function of
SUZUKI Scan Tool” under “Scan Tool Data in Section 10B”.
• Check each part in the order from the top of the following list.
Power Door Lock System Operation Inspection
S6JB0A9604002
1) Check the following operation:
a) Turn the driver side key cylinder is turned LOCK once, check all doors lock.
b) Turn the driver side door key cylinder is turned UNLOCK position with door key twice, check all doors unlock.
c) With all doors unlocked, insert key in key cylinder of driver side door and turn it to lock side, turn it again to lock
side within 3 seconds and check that no door can be opened even when door lock knob is moved to unlock
side (dead lock function, if equipped).
If malfunction is found, go to “Power Door Lock System Symptom Diagnosis”.
Condition
Possible cause
Correction / Reference Item
All door can not be locked
/ unlocked by all of
switches
Circuit fuse blown
Replace fuse and check for short circuit.
Wiring or grounding faulty
Repair circuit.
BCM faulty
Replace after making sure that none of above
parts is faulty.
All door can not be locked
/ unlocked by only power
door lock switch
Circuit fuse blown
Replace fuse and check for short circuit.
Power door lock switch faulty
Check power door lock switch referring to
“Power Door Lock Switch Inspection”.
Wiring harness connected to power door
lock switch faulty
Repair.
Wiring or grounding faulty
Repair circuit.
BCM faulty
Replace after making sure that none of above
parts is faulty.
All door can not be locked
/ unlocked by only key
cylinder switch
Circuit fuse blown
Replace fuse and check for short circuit.
Key cylinder switch faulty
Check key cylinder switch referring to “Door
Key Cylinder Switch Inspection”.
Wiring or grounding faulty
Repair circuit.
BCM faulty
Replace after making sure that none of above
parts is faulty.
Only one door can not be
locked / unlocked
Power door lock actuator faulty
Check actuator referring to “Power Door Lock
Actuator Inspection”.
Wiring harness connected to applicable
door lock actuator faulty
Repair.
BCM faulty
Replace after making sure that none of above
parts is faulty.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст