Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 502
9E-19 Glass / Windows / Mirrors:
Rear End Door Window Defogger Relay
Inspection
S6JB0A9506013
1) Disconnect negative (–) cable from battery.
2) Remove rear end door window defogger relay
(included in integration relay) (1) from main fuse box
(2).
3) Check that there is no continuity between terminal
“a” and “b”. If there is continuity, replace relay.
4) Check that there is continuity between terminals “a”
and “b” when a 12 V battery is connected to
terminals “a” and “c”.
If malfunction is found, replace it with a new one.
Rear End Door Window Defogger Wire
Inspection
S6JB0A9506014
NOTE
• When cleaning rear end door window
glass, use a dry cloth to wipe it along heat
wire (1) direction.
• When cleaning glass, do not use detergent
or abrasive-containing glass cleaner.
• When measuring wire voltage, use a tester
with positive probe (2) wrapped with a tin
foil (3) which should be held down on wire
by finger pressure.
Wire Damage Inspection
1) Start engine.
2) Turn on defogger switch.
3) Measure voltage at the center of each defogger wire
(1), and check defogger wire condition according to
the following table.
If defogger wire open is found, go to next step.
Defogger wire voltage
2
1
I5JB0A950031-01
“c”
“b”
“a”
“b”
“a”
“c”
I5JB0A950032-02
Voltage
Circuit
0 – 1 V Defogger wire open between its center
and defogger wire power source terminal
end (2)
4 – 6 V Normal condition
10 – 12 V Defogger wire open between its center
and defogger wire ground terminal end
(3)
I2RH01950002-01
2
1
I5JB0A950033-01
Glass / Windows / Mirrors: 9E-20
4) Touch voltmeter negative (–) lead to defogger wire
ground terminal end (1).
5) Touch voltmeter positive (+) lead with a foil strip to
defogger wire power source terminal end (2), then
move it along wire to defogger wire ground terminal
end (1).
The place where voltmeter fluctuates from 10 – 12 V
to 0 – 1 V is where there is open.
If found defective, repair defogger wire referring to
“Rear End Door Window Defogger Wire Repair”.
Rear End Door Window Defogger Wire Repair
S6JB0A9506015
1) Use white gasoline for cleaning.
2) Apply masking tape (1) at both upper and lower
sides of heat wire (2) to be repaired.
3) Apply commercially-available repair agent (3) with a
fine-tip brush (4).
4) 2 to 3 minutes later, remove masking tapes (1).
5) Leave repaired heat wire as it is for at least 24 hours
before operating the defogger again.
Power Window Main Switch Inspection
S6JB0A9506016
Switch for driver side window
1) Remove driver side door trim referring to step 1) to
3) of “Front Door Glass Removal and Installation”.
2) Remove power window main switch from door trim.
3) Connect 12 V battery positive (+) terminal to terminal
“IG” of power window main switch and its negative (–
) terminal to terminal “E” of power window main
switch.
4) Check for continuity between terminals as shown
below.
If check result is not as specified, replace power
window main switch.
2
1
I5JB0A950034-01
I2RH01950005-01
[A]: LH steering vehicle
[B]: RH steering vehicle
I5JB0A950035-03
9E-21 Glass / Windows / Mirrors:
Switch for other window than driver side
1) Remove driver side door trim referring to step 1) to
3) of “Front Door Glass Removal and Installation”.
2) Remove power window main switch from door trim.
3) Check for continuity between terminals as shown
below.
If check result is not as specified, replace power window
main switch.
Power Window Sub Switch Inspection
S6JB0A9506017
1) Remove front and/or rear door trim from door panel,
refer to Step 1) to 3) of “Front Door Glass Removal
and Installation” and/or “Rear Door Glass Removal
and Installation”.
2) Remove power window sub switch from door trim.
3) Check for continuity between terminals at each
switch condition.
If check result is not as specified, replace switch.
[A]: LH steering vehicle
[B]: RH steering vehicle
I5JB0A950036-02
I5JB0A950037-01
Glass / Windows / Mirrors: 9E-22
Door Mirror Components
S6JB0A9506018
Door Mirror Removal and Installation
S6JB0A9506019
When removing or installing door mirror, refer to the
figure in “Door Mirror Components”.
Power Door Mirror Switch Inspection
S6JB0A9506020
1) Remove driver side door trim referring to step 1) to
3) of “Front Door Glass Removal and Installation”.
2) Remove power window main switch from door trim.
3) Check for continuity between terminals at each
switch position.
If check result is not as specified, replace door mirror
switch.
“1”
“3”
“2”
1
2,
2,
2,
I5JB0A950038-02
1. Door mirror
2. Door mirror mounting nut
:Tighten nuts in such order as indicated in the figure.
A
B
C
D
E
F
G
Up
Down
Left
Right
L
R
A
B
C
D
E
F
G
I5JB0A950039-01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст