Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 540
10C-21 Immobilizer Control System: For Petrol Engine Model
DTC P1623: Unregistered Transponder
S6JB0AA314014
Wiring Diagram
Refer to “Immobilizer Control System Wiring Circuit Diagram: For Petrol Engine Model”
Detecting Condition and Trouble Area
Troubleshooting
Detecting Condition
Trouble Area
Transponder code in the transponder built in the ignition
key is invalid.
• Use of the unregistered ignition key
• Immobilizer control module (ICM) faulty
• ECM faulty
Step
Action
Yes
No
1
Diagnostic Trouble Code (DTC) confirmation
1) Clear DTC(s) referring to “Diagnostic Trouble Code
(DTC) Clearance: For Petrol Engine Model”.
2) Turn the ignition switch to OFF position.
3) Check if any DTC is detected referring to “Diagnostic
Trouble Code (DTC) Check: For Petrol Engine Model”.
Is DTC P1623 still detected?
Go to Step 2.
The troubleshooting is
completed.
2
Diagnostic Trouble Code (DTC) check
Is any DTC other than P1623 is detected in Step 1?
Perform the
troubleshooting
referring to the
corresponding
flowchart, and then go
to Step 3.
Go to Step 3.
3
Registration of the unregistered ignition key with ECM
and Diagnostic Trouble Code (DTC) check
1) Register the transponder code in the transponder in the
unregistered ignition key with ECM referring to
“Registration of the Ignition Key: For Petrol Engine
Model”.
2) Check if that DTC P1623 is detected referring to
“Diagnostic Trouble Code (DTC) Check: For Petrol
Engine Model”.
Is DTC P1623 detected?
Go to Step 4.
The troubleshooting is
completed.
4
Immobilizer control module (ICM) check
1) Check immobilizer control module (ICM) referring to
“Inspection of Immobilizer Control Module (ICM) and Its
Circuit: For Petrol Engine Model”.
Is immobilizer controller assembly normal?
Replace ECM with new
one referring to “Engine
Control Module (ECM)
Removal and
Installation: For Petrol
Engine Model in Section
1C”, and then perform
“Procedure after ECM
Replacement: For
Petrol Engine Model”.
Replace immobilizer
control module (ICM)
with new one referring
to “Immobilizer Control
Module (ICM) Removal
and Installation: For
Petrol Engine Model”.
Immobilizer Control System: For Petrol Engine Model 10C-22
DTC P1625: Immobilizer Antenna Error
S6JB0AA314015
Wiring Diagram
Refer to “Immobilizer Control System Wiring Circuit Diagram: For Petrol Engine Model”
Detecting Condition and Trouble Area
Troubleshooting
Detecting Condition
Trouble Area
Immobilizer control module (ICM) is faulty.
• Immobilizer control module faulty
• ECM faulty
Step
Action
Yes
No
1
Diagnostic Trouble Code (DTC) confirmation
1) Clear DTC(s) referring to “Diagnostic Trouble Code
(DTC) Clearance: For Petrol Engine Model”.
2) Turn the ignition switch to OFF position.
3) Check if any DTC is detected referring to “Diagnostic
Trouble Code (DTC) Check: For Petrol Engine Model”.
Is DTC P1625 still detected?
Go to Step 2.
The troubleshooting is
completed.
2
Immobilizer control module (ICM) replacement and
Diagnostic Trouble Code (DTC) check
1) Replace immobilizer control module (ICM) referring to
“Immobilizer Control Module (ICM) Removal and
Installation: For Petrol Engine Model”.
2) Check if DTC P1625 is still detected referring to
“Diagnostic Trouble Code (DTC) Check: For Petrol
Engine Model”.
Is DTC P1625 still detected?
Replace ECM with new
one referring to “Engine
Control Module (ECM)
Removal and
Installation: For Petrol
Engine Model in Section
1C”, and then perform
“Procedure after ECM
Replacement: For
Petrol Engine Model”.
The troubleshooting is
completed.
10C-23 Immobilizer Control System: For Petrol Engine Model
DTC P1636: Immobilizer Information Registration Failure
S6JB0AA314016
Wiring Diagram
Refer to “Immobilizer Control System Wiring Circuit Diagram: For Petrol Engine Model”
DTC Detecting Condition and Trouble Area
Troubleshooting
Detecting Condition
Trouble Area
The registration of the immobilizer control system
information in ECM is failed.
• CAN communication wire circuits faulty
• Steering angle sensor (if equipped) faulty
• Keyless start control module (if equipped) faulty
• 4WD control module (if equipped) faulty
• TCM (if equipped) faulty
• BCM faulty
• ABS/ESP
® control module faulty
• Combination meter faulty
• ECM faulty
Step
Action
Yes
No
1
Diagnostic Trouble Code (DTC) confirmation
1) Clear DTC(s) referring to “Diagnostic Trouble Code
(DTC) Clearance: For Petrol Engine Model”.
2) Turn the ignition switch to OFF position.
3) Check if any DTC is detected referring to “Diagnostic
Trouble Code (DTC) Check: For Petrol Engine Model”.
Is DTC P1636 still detected?
Go to Step 2.
The troubleshooting is
completed.
2
Diagnostic Trouble Code (DTC) check in ECM
Is any DTC other than P1636 detected in Step 1?
Perform the
troubleshooting
referring to the
corresponding
flowchart.
Go to Step 3.
3
Diagnostic Trouble Code (DTC) check in BCM
1) Check BCM for DTC referring to “DTC Check in Section
Is any DTC detected?
Perform the
troubleshooting
referring to the
corresponding flowchart
in Section 10B.
Go to Step 4.
4
Replacement of BCM
1) Replace BCM with new one referring to “BCM Removal
and Installation in Section 10B”.
2) Check ECM for DTC referring to “Diagnostic Trouble
Code (DTC) Check: For Petrol Engine Model”.
Is DTC P1636 still detected?
Go to Step 5.
The troubleshooting is
completed.
5
Replacement of ECM
1) Replace ECM with new one referring to “Engine Control
Module (ECM) Removal and Installation: For Petrol
Engine Model in Section 1C”.
2) Check ECM for DTC referring to “Diagnostic Trouble
Code (DTC) Check: For Petrol Engine Model”.
Is DTC P1636 still detected?
Recheck CAN
communication wire
circuits and poor
connection at ECM,
ABS/ESP
® control
module and BCM
connectors.
The troubleshooting is
completed.
Immobilizer Control System: For Petrol Engine Model 10C-24
DTC P1638: Immobilizer Information Mismatched
S6JB0AA314017
Wiring Diagram
Refer to “Immobilizer Control System Wiring Circuit Diagram: For Petrol Engine Model”
DTC Detecting Condition and Trouble Area
Troubleshooting
Detecting Condition
Trouble Area
• The immobilizer control system information in ECM and
the one in BCM does not match.
• The registration of the immobilizer control system
information in ECM is failed.
• Use of the wrong ECM
• Steering angle sensor (if equipped) faulty
• Keyless start control module (if equipped) faulty
• 4WD control module (if equipped)
• TCM (if equipped) faulty
• CAN communication wire circuits faulty
• BCM faulty
• Combination meter faulty
• ABS/ESP
® control module faulty
• ECM faulty
Step
Action
Yes
No
1
Diagnostic Trouble Code (DTC) confirmation
1) Clear DTC(s) referring to “Diagnostic Trouble Code
(DTC) Clearance: For Petrol Engine Model”.
2) Turn the ignition switch to OFF position.
3) Check if any DTC is detected referring to “Diagnostic
Trouble Code (DTC) Check: For Petrol Engine Model”.
Is DTC P1638 still detected?
Go to Step 2.
The troubleshooting is
completed.
2
Diagnostic Trouble Code (DTC) confirmation
1) Disconnect negative (–) cable from battery for more than
5 seconds.
2) Connect negative (–) cable to battery.
3) Check if any DTC is detected referring to “Diagnostic
Trouble Code (DTC) Check: For Petrol Engine Model”.
Is DTC P1638 still detected?
Go to Step 3.
The troubleshooting is
completed.
3
Check ECM specification
1) Check ECM part number to see if ECM is applicable to
the vehicle in service.
Is a correct ECM used for the vehicle in service?
Go to Step 2.
Replace ECM with the
correct one and recheck
if DTC P1638 is still
detected by ECM.
4
Diagnostic Trouble Code (DTC) check in ECM
Is any DTC other than P1638 detected in Step 1?
Perform the
troubleshooting
referring to the
corresponding
flowchart.
Go to Step 3.
5
Diagnostic Trouble Code (DTC) check in BCM
1) Check BCM for DTC referring to “DTC Check in Section
10B”.
Is any DTC detected?
Perform the
troubleshooting
referring to the
corresponding flowchart
in Section 10B.
Go to Step 5.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст