Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 237
3B-19 Differential: Front
09913–50121
09913–65135
Oil seal remover
Bearing puller
09913–75510
09913–75520
Bearing installer
Bearing installer
09913–75821
09913–85210
Bearing installer attachment
Bearing installer
09922–66021
09922–75222
Flange holder
Differential gear preload
adjuster
09922–76520
09924–74510
Bevel pinion gauge block
Bearing and oil seal handle
09924–84510–004
09924–84510–005
Bearing installer attachment
Bearing installer attachment
(D)
09925–14520
09925–86010
Bearing and oil seal installer
(80 x 50 mm)
Bearing puller attachment
09925–88210
09926–78311
Bearing puller attachment
Differential bevel pinion
dummy
Differential: Front 3B-20
09926–78311–002
09926–78320
Pinion mounting dummy
Mounting dummy
09928–06510
09930–30104
Differential torque checking
tool
Sliding shaft
09940–53111
09941–64511
Differential side bearing
installer
Bearing and oil seal remover
(30 mm Min.)
09951–16070
09951–16090
Shim adjuster attachment
Oil seal installer
09951–18210
09951–46010
Oil seal remover & installer
No. 2
Drive shaft oil seal installer
3B-21 Differential: Rear
Rear
General Description
Rear Differential Construction
S6JB0A3221001
Refer to “Front Differential Construction: Front”.
Diagnostic Information and Procedures
Rear Differential Symptom Diagnosis
S6JB0A3224001
Refer to “Front Differential Symptom Diagnosis: Front”.
Repair Instructions
Rear Differential Oil Change
S6JB0A3226001
Refer to “Front Differential Oil Change: Front”.
The point which is different from the front differential is described.
Rear differential oil capacity
Reference:
• For 4WD model: 0.8 – 0.9 liters (1.7/1.4 – 1.9/1.6 US/Imp. pt.)
• For 2WD model: 0.8 – 1.0 liters (1.7/1.4 – 2.1/1.8 US/Imp. pt.)
Differential: Rear 3B-22
Rear Differential Unit Components
S6JB0A3226002
Rear Differential Dismounting and Remounting
S6JB0A3226003
Dismounting
1) Lift up vehicle and drain oil from rear differential.
2) Remove rear propeller shaft referring to “Propeller
Shaft Removal and Installation in Section 3D”.
3) Remove exhaust center pipe referring to “Exhaust
System Components: For Petrol Engine Model in
Section 1K” or “Exhaust System Components: For
Diesel Engine Model in Section 1K”.
4) Remove rear drive shafts referring to “Rear Drive
Shaft Assembly Removal and Installation: Rear in
Section 3A”.
5) Dismount rear differential as follows.
• 3 door model
a. Remove fuel tank cover (1).
(a)
5
(a)
3
(b)
4
2
1
[A]
[B]
I6JB01322001-02
[A]: 4WD model
4. Front mounting bracket bolt
[B]: 2WD model
5. Front mounting bolt
1. Rear differential
: 120 N
⋅m (12.0 kgf-m, 87.0 lb-ft)
2. Front mounting bracket
: 50 N
⋅m (5.0 kgf-m, 36.5 lb-ft)
3. Rear mounting bolt
1
I5JB0A322006-01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст