JAC S2. Service Manual — part 10
Exterior Trim
Exterior Trim 133
X
、Outer Water Splitting Strip of Front Side Vehicle Door
(I)Removal
1. Remove outer water splitting strip of front side vehicle door
1). Lift vehicle door window to the lowest;
2). Remove fixed bolt of outer water splitting strip of front s;
3). Pry outer water splitting strip of front side vehicle door from
inside of vehicle door;
△Note Please don’t force too much when removing,
because it may cause components deformed.
△Note Check strip visually when removing, if deformed,
please replace.
(II)Installation
1. Install outer water splitting strip of front side vehicle door
1). Align outer water splitting strip of front side vehicle door to
flange of door pillar, and install outer water splitting strip
of front side vehicle door in place from front part slowly;
2). Tighten rear part fixed bolt of outer water splitting strip of
front side vehicle door;
Tighten torque
3~5N
·m
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Exterior Trim
Exterior Trim 134
XI、Waterproof Membrane of Front Vehicle Door
(I)Removal
1. Open engine compartment cover
2. Disconnect battery negative electrode
3. Remove front triangle window cover plate assembly Refer to "Front door trim panel assembly"
4. Remove front door trim panel assembly Refer to "Front door trim panel assembly"
5. Remove installation bracket of front door inclined handle
1). Remove 2 fixed bolts of installation bracket of front door
inclined handle;
2). Take down installation bracket of front door inclined
handle;
6. Remove waterproof membrane of front vehicle door
1). Disconnect connection of waterproof membrane and vehicle
door, and take down waterproof membrane;
△Note Don’t touch surface of adhesion agent to avoid
weaken adhesion effect.
△Note Be careful with waterproof membrane to avoid
damage waterproof membrane.
(II)Installation
1. Install waterproof membrane of front vehicle door
1). Install waterproof membrane to right position of vehicle
inside ;
2. Install installation bracket of front door inclined handle
1). Place installation bracket to right position, and tighten 2
fixed bolts;
3. Install front door trim panel assembly
4. Install front triangle window cover plate assembly
5. Connect battery negative electrode
6. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Exterior Trim
Exterior Trim 135
XII、Waterproof Membrane of Rear Vehicle Door
(I)Remove
1. Open engine compartment cover
2. Disconnect battery negative electrode
3. Remove rear door triangle window cover plate assembly Refer to "Rear door trim panel assembly"
4. Remove rear door trim panel assembly Refer to "Rear door trim panel assembly"
5. Remove installation bracket of rear door handle panel
1). Remove 2 fixed bolts connecting installation bracket of rear
door handle panel and rear vehicle door;
2). Take down installation bracket of rear door handle panel;
6. Remove waterproof membrane of rear vehicle door
1). Separate connection of waterproof membrane and vehicle
door, and take down waterproof membrane;
△Note Don’t touch surface of adhesion agent to avoid
weaken adhesion effect.
△Note Be careful with waterproof membrane to avoid
damage waterproof membrane.
(II)Installation
1. Install waterproof membrane of rear vehicle door
1). Install waterproof membrane to inside vehicle door, and
tighten;
2. Install installation bracket of rear door handle panel
1). Place installation bracket to installation position, and tighten
2 fixed bolts;
3. Install rear door trim panel assembly
4. Install rear door triangle window cover plate assembly
5. Connect battery negative electrode
6. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Exterior Trim
Exterior Trim 136
XIII、Door Frame Rubber Strip of Front Side Vehicle Door
(I)Removal
1. Remove front door threshold guard panel assembly Refer to "Front door threshold guard panel assembly"
2. Remove door frame rubber strip of front side vehicle door
1). Disconnect door frame rubber strip from vehicle body from
one end;
2). Pull out door frame rubber strip of front side vehicle door
slowly;
(II)Installation
1. Install door frame rubber strip of front side vehicle door
1). Place door frame rubber strip to installation position;
2). Knock slightly using rubber hammer to make it be installed
in place;
2. Install front door threshold guard panel assembly
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Exterior Trim
Exterior Trim 137
XIV、Door Frame Rubber Strip of Rear Side Vehicle Door
(I)Removal
1. Remove rear threshold guard panel assembly Refer to "Rear threshold guard panel assembly"
2. Remove door frame rubber strip of rear side vehicle door
1). Disconnect door frame rubber strip from vehicle body from
one end;
2). Pull out door frame rubber strip of rear side vehicle door
slowly;
(II)Installation
1. Install door frame rubber strip of rear side vehicle door
1). Place door frame rubber strip to installation position;
2). Knock slightly using rubber hammer to make it be installed
in place;
2. Install rear threshold guard panel assembly
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Exterior Trim
Exterior Trim 138
XV、Inner Water Splitting Strip of Rear Side Vehicle Door
(I)Removal
1. Open engine compartment cover
2. Disconnect battery negative electrode
3. Remove rear door triangle window cover plate assembly Refer to "Rear door triangle window cover plate assembly"
4. Remove rear door trim panel assembly Refer to "Rear door trim panel assembly"
5. Remove inner water splitting strip of rear side vehicle door
1). Take down inner water splitting strip of rear side vehicle
door slowly with hands from one side;
△Note Please don’t force too much when removing,
because it may cause component deformed.
(II)Installation
1. Install inner water splitting strip of rear side vehicle door
1). Install one end first, and then install inner water splitting
strip of rear side vehicle door in place slowly;
2. Install rear door trim panel assembly
3. Install rear door triangle window cover plate assembly
4. Connect battery negative electrode
5. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Exterior Trim
Exterior Trim 139
XVI、Outer Water Splitting Strip of Rear Side Vehicle Door
(I)Remove
1. Remove outer water splitting strip of rear side vehicle door
1). Lift vehicle door window to the lowest;
2). Remove fixed bolts both in left and right side of outer water
splitting strip of rear side vehicle door and vehicle door;
3). Pry outer water splitting strip of rear side vehicle door from
inside of vehicle door;
△Note Please don’t force too much when removing,
because it may cause components deformed.
△Note Check strip visually when removing, if deformed,
please replace.
(II)Installation
1. Install outer water splitting strip of rear side vehicle door
1). Align outer water splitting strip of rear side vehicle door to
flange of door pillar, and install outer water splitting strip
of rear side vehicle door in place from front part slowly;
2). Tighten rear part fixed bolt in left and right side of outer
water splitting strip of front side vehicle door;
Tighten torque
5~7N
·m
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Exterior Trim
Exterior Trim 140
XVII、Tail Door Sealing Strip
(I)Removal
1. Remove tail door sealing strip
1). Remove hatstand knot from installation bracket, and
disconnect tail door sealing strip from vehicle body from
one end;
2). Pull out tail door sealing strip slowly;
(II)Installation
1. Install tail door sealing strip
1). Place tail door sealing strip to installation position
2). Knock slightly using hammer to make it be installed in
place;
3). Hang hatstand knot to installation bracket;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seat and Safety Belt
Seat and Safety Belt 141
Seat and Safety Belt
I、Summary
(I)Structure Overview
Location Diagram
1. Front seat assembly
2. Front seat headrest
3. Rear seat assembly
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seat and Safety Belt
Seat and Safety Belt 142
1. Left front safety belt assembly
2. Left front safety belt inserting lock assembly
3. Right front safety belt inserting lock assembly
4. Right front safety belt assembly
5. Left rear three-point-type safety belt assembly
7. Right rear three-point-type safety belt assembly
6. Left rear safety belt inserting lock and middle safety belt clasp lock assembly
8. Middle three-point-type safety belt and safety belt inserting lock assembly
(II)Torque Parameter
No.
Item
Torque
(N·m)
1
Fixed bolt of front seat
45~55
2
Fixed bolt of rear seat backrest middle fixed bracket assembly
45~55
3
Lower fixed point bolt of safety belt
45~55
4
Fixed bolt of rear seat backrest lower fixed bracket and seat backrest
45~55
5
Fixed bolt of safety belt inserting lock
45~55
(III)Maintenance Note
(1). Assemble sequence of seats fixed bolts.
(2). Put the seats to the rearmost position and check the locking condition of each slide; then fasten the front fixed bolts temporarily.
(3). Put the seats to the most front position and check the locking condition of each slide; then fasten the rear fixed bolts temporarily.
(4). Put the seats to the rearmost position and fasten the front fixed bolts completely.
(5). Check whether seats can move forward and backward smooth and locks locked properly or not.
(6). Replace the damaged rear seats cushion clips.
(7). The assembly procedure of seats fixed bolts and nuts.
(8). Check whether the operation of the tilt seats and folding seat cushion is smooth or not.
II、Front Seat Assembly
(I)Removal
1. Open engine compartment cover
2. Disconnect battery negative electrode
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seat and Safety Belt
Seat and Safety Belt 143
3. Remove front seat assembly
1). Remove 2 fixed bolts of front part of seat;
2). Remove 2 fixed bolts of rear part of seat;
3). Disconnect safety belt not inserting warning wiring harness
connector, and take down seat;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seat and Safety Belt
Seat and Safety Belt 144
(II)Installation
1. Install front seat assembly
1). Connect safety belt not inserting warning wiring harness
connector;
2). First pre-install 2 bolts of front part of seat, slip seat forward
to forefront, and then pre-install 2 bolts of rear part of seat;
at last tighten rear outside bolt of seat, rear inside bolt,
front side two bolts;
Tighten torque
45~55N·m
2. Connect battery negative electrode
3. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seat and Safety Belt
Seat and Safety Belt 145
III、Seat Headrest
(I)Removal
1. Remove seat headrest
1). Press unlock button on headrest guide sleeve of seat
headrest;
2). Pull seat headrest upward;
(II)Installation
1. Install seat headrest
1). Press seat headrest unlock button in;
2). Insert seat headrest to headrest guide sleeve, and adjust
height of seat headrest according to requirement;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seat and Safety Belt
Seat and Safety Belt 146
IV、Rear Seat Backrest
(I)Removal
1. Remove rear seat cushion assembly
1). Lift rear seat cushion assembly upward, pull out cushion
from cushion buckles, and take out rear seat cushion
assembly;
2. Remove rear seat backrest assembly
1). Remove lower fixed bolt of rear seat middle safety belt;
2). Press two sides unlock buttons of seat backrest upper part,
and rotate backrest forward;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seat and Safety Belt
Seat and Safety Belt 147
3). Remove fixed bolt both in left/right side backrest lower fixed
bracket and backrest assembly, and take out backrest assembly;
(II)Installation
1. Install rear seat backrest assembly
1). Place rear seat backrest assembly to installation position;
2). Tighten fixed bolt both in left/right side backrest lower
fixed bracket and backrest assembly, and take out backrest
assembly;
Tighten torque
45~55N·m
3). Rotate backrest backward, and tighten lower fixed bolt of
rear middle safety belt;
Tighten torque
45~55N·m
2. Install rear seat cushion assembly
1). Insert rear seat cushion to lower part of backrest, and cross
safety belt inserting lock and safety belt clap lock from
cushion opening port;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seat and Safety Belt
Seat and Safety Belt 148
2). Install pothook of front part of cushion to fixed buckle of
rear seat;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст