Engine JAC HFC4DA1-2C. Manual — part 145
ABS
ABS
ABS
ABS Anti-lock
Anti-lock
Anti-lock
Anti-lock Brake
Brake
Brake
Brake System
System
System
System
101
Removal/Installation
Removal/Installation
Removal/Installation
Removal/Installation
ABS
ABS
ABS
ABS system
system
system
system
1.
Remove the negative cable of battery.
2.
Drain the brake fluid in the hydraulic brake system
completely.
3.
Loosen the oil pipe of brake master cylinder.
4.
Remove the ABS connector.
5.
Remove the brake fluid pipe from ABS hydraulic
assembly. Wrap the pipe with plastic bag to avoid
dirt. Use clean water to wash the surface that
having brake fluid on it.
6.
Remove the mounting bolts from ABS hydraulic
assembly and then remove the assembly.
ABS
ABS
ABS
ABS Anti-lock
Anti-lock
Anti-lock
Anti-lock Brake
Brake
Brake
Brake System
System
System
System
102
Removal/Installation
Removal/Installation
Removal/Installation
Removal/Installation (Continued)
(Continued)
(Continued)
(Continued)
Installation
1.
Clean the surface of ABS hydraulic assembly and
fix the assembly onto bracket with bolts.
2.
Install the brake pipe onto the ABS hydraulic
assembly.
Attention:
Attention:
Attention:
Attention:
As for the installation of aluminum alloy parts, the
brake pipe should be fit in place smoothly by
correct alignment; otherwise, the original part
bodies may be damaged easily.
3.
Insert the ABS plug into relevant socket.
Attention:
Attention:
Attention:
Attention:
The ABS plug should be installed in carefully and
smoothly instead of violently.
4.
Install and fasten the oil pipe of brake master
cylinder.
5.
Fill the reservoir of master cylinder with brake
fluid.
6.
Two persons shall work together to bleed the air in
brake line until pure brake fluid is drained out. Air
bleeding order: left rear, right front, right rear and
left front wheels.
7.
Connect the negative cable of battery.
ABS
ABS
ABS
ABS Anti-lock
Anti-lock
Anti-lock
Anti-lock Brake
Brake
Brake
Brake System
System
System
System
103
Removal/Installation
Removal/Installation
Removal/Installation
Removal/Installation (Continued)
(Continued)
(Continued)
(Continued)
Wheel
Wheel
Wheel
Wheel speed
speed
speed
speed sensor
sensor
sensor
sensor
1.
Disconnect the negative cable of battery.
2.
Lift the vehicle.
3.
Disconnect the plug of wheel speed sensor and
remove the harness fixture of sensor.
4.
Remove the mounting bolts from wheel speed
sensor and then remove the sensor.
Installation
1.
Insert the sensor into relevant hole and fix it with
bolt.
2.
Fix the sensor harness and install the harness onto
the plug.
3.
Lower the vehicle.
4.
Connect the negative cable of battery.
TR
TR
TR
TR Transmission
Transmission
Transmission
Transmission Shaft
Shaft
Shaft
Shaft
- 105 -
Transmission
Transmission
Transmission
Transmission Shaft
Shaft
Shaft
Shaft
Applied models: SUNRAY products manufactured by JAC
Subject
Page
Instruction
Instruction
Instruction
Instruction and
and
and
and Operation
Operation
Operation
Operation
Transmission Shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 106
Explosive View of Transmission Shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 106
Introduction of Transmission Shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Diagnosis
Diagnosis
Diagnosis
Diagnosis and
and
and
and Testing
Testing
Testing
Testing
Transmission Shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 107
Inspection and Confirmation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..107
Fault Symptom Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Removal/Installation
Removal/Installation
Removal/Installation
Removal/Installation
Removal
of Transmission shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Installation of Transmission shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст