Hummer H3. Manual — part 1188
![](/vehicles/kig/fin/ghing/qumes.png)
DTC B2462 does not set if DTC B1328 or B1327 is current.
Conditions for Setting the DTC
The navigation radio test the GPS antenna every 0.3 second.
The radio determines there is an open in the GPS antenna.
DTC B2462 does not set if DTC B1328 or B1327 is current.
Action Taken When the DTC Sets
Unable to get GPS location updated, the radio uses the last reported position and the vehicle
speed signal to calculate the vehicle position.
Route guidance may be inaccurate.
This failure has no effect outside the Navigation System.
Conditions for Clearing the DTC
A current DTC clears when the radio does not detect the failure for more than 10 seconds.
A history DTC clears after 50 ignition cycles with no repeat of the failure.
Diagnostic Aids
An intermittent condition may be caused by the following:
Mis-routed harness
Rubbed through wire insulation
Broken wire inside the insulation
Test Description
The numbers below refer to the step numbers on the diagnostic table.
1: Determines if the malfunction is present.
3: Determines if the malfunction is due to an internal fault in the navigation radio or a GPS
antenna failure.
DTC B2462
Step
Action
Values
Yes
No
Schematic Reference: Radio/Navigation System Schematics
Connector End View Reference: Entertainment/Communication Connector End
2007 Hummer H3
2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3
![](/vehicles/kig/fin/ghing/zokerb.png)
Views
1
Did you perform the Diagnostic
System Check - Vehicle?
-
Go to Step 2
Go to
Diagnostic
System
Check -
Vehicle
2
1. Turn OFF the ignition.
2. Disconnect the Global
Positioning System (GPS)
coaxial cable connector.
3. Measure the voltage between
the center conductor and the
shield of the coaxial cable still
attached to the navigation
radio.
Is the voltage within the specified
range?
4.0-5.5 V
Go to Step 5 Go to Step 3
3
Test the GPS cable for an open or
short to ground. Refer to Circuit
Testing and Wiring Repairs .
Did you find and correct the
condition?
-
Go to Step 7 Go to Step 4
4
Inspect for poor connections at the
harness connector of the GPS cable.
Refer to Testing for Intermittent
Conditions and Poor Connections
and Connector Repairs .
Did you find and correct the
condition?
-
Go to Step 7 Go to Step 6
5
Replace the GPS antenna. Refer to
Global Positioning System (GPS)
Antenna Replacement.
Did you complete the replacement?
-
Go to Step 7
-
6
Replace the navigation radio. Refer
to Radio Replacement.
Did you complete the replacement?
-
Go to Step 7
-
1. Use the scan tool in order to
2007 Hummer H3
2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3
![](/vehicles/kig/fin/ghing/bigingijer.png)
DTC B2470
Circuit Description
The cellular antenna is connected to the vehicle communication interface module (VCIM) with a
RG-58 coax cable. The VCIM polls the data from the cellular antenna once every second.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2470 Cellular Phone Antenna Circuit Malfunction
Conditions for Running the DTC
The ignition must be in the RUN or ACC position.
The system voltage is at least 9.5 volts and no more than 15.5 volts.
All the above conditions are present for greater than 1 second.
Conditions for Setting the DTC
The VCIM does not detect the presence of a cellular antenna.
All the above conditions are present for greater than 1 second.
Action Taken When the DTC Sets
The OnStar® status LED turns red.
The vehicle is unable to connect to the OnStar® Call Center.
Conditions for Clearing the DTC
The VCIM detects the presence of a cellular antenna.
A history DTC clears after 50 malfunction-free ignition cycles.
7
clear the DTC.
2. Operate the vehicle within the
Conditions for Running the
DTC as specified in the
supporting text.
Does the DTC reset?
-
Go to Step 2 System OK
2007 Hummer H3
2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3
![](/vehicles/kig/fin/ghing/ieyous.png)
The VCIM receives the clear DTC command from the scan tool.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
2: This step tests the condition of the cellular antenna.
3: This step tests the condition of the cellular antenna coax and for proper ground of the
cellular antenna.
DTC B2470
Step
Action
Value
Yes
No
Schematic Reference: OnStar Schematics
Connector End View Reference: Entertainment/Communication Connector End
Views
1
Did you perform the Diagnostic
System Check - Vehicle?
-
Go to Step 2
Go to
Diagnostic
System
Check -
Vehicle
2
Inspect the cellular antenna and
cellular antenna coupling assembly for
damage.
Is the antenna assembly damaged?
-
Go to Step 7 Go to Step 3
3
1. Disconnect the cellular antenna
coax from the vehicle
communication interface module
(VCIM).
2. Measure the resistance between
the center conductor and the
outer metal shield.
Does the meter read out of limits?
IMPORTANT:
The vehicle may be equipped with
sectioned coax. Test each section and
replace only the faulty section, not the
entire length of coax.
-
Go to Step 4 Go to Step 5
2007 Hummer H3
2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст