Hummer H1 (2006+). Manual — part 301
10-66 Body
______________________________________________________________________
full turn on the adjusting screw as a start point and squeeze the seal in the areas that measured loose with the paper check.
Recheck the interface with the paper (Figure 10-73) and continue to squeeze, if necessary, until the desired interface is
obtained.
Figure 10-74: Adjusting Fixed Seal Channels
8.
Install the armrest mount plate, the vapor barrier, the door trim panel, the door strap and the armrest.
Door Glass “Wind Noise” Diagnosis and Repair/Side Window Alignment
Wind noise or whistle generating from the side windows at highway speeds is the result of inadequate sealing of the glass at the up-
per seal. The glass must be properly aligned in the window opening, adjust door glass as follows:.
1.
Loosen, but do not remove, the lift channel bracket mounting bolts.
2.
Place a block of wood (or equivalent symmetrical object) across the upper seal of the window opening.
3.
Roll the window up so that the glass contacts the block of wood and squares itself on the window opening.
4.
Tighten the lift channel bracket mounting bolts.
5.
Verify proper window operation
HOOD, HOOD LATCH AND PROP ROD
Hood Latch and Bracket Replacement
Removal
NOTE: If only the rubber latch is to be replaced, the spring pin does not have to be completely out of the base.
1.
Remove the spring pin, limiter straps and the rubber isolator from the base (Figure 10-75).
2.
Remove the two bolts and the base from the body.
3.
Remove the four bolts, latch bracket, latch plate, hood latch stop bracket and the bolt tapping plate from the hood. (Figure
10-75).
Disassembly
Remove the cotter pin, latch pin, spring pin, two rollers, two limiter straps and the hood latch from the rubber isolator (Figure
10-75).
Assembly
Secure the hood latch and the limiter straps to the rubber isolator with the two rollers, latch pin and the cotter pin (Figure 10-75).
WIDE JAW PLIERS
MASKING
TAPE
WINDOW
SEAL
_____________________________________________________________________
Body 10-67
Figure 10-75: Hood Latch Replacement
Installation
1.
Secure the latch bracket, latch plate and the hood latch stop bracket to the hood with the four bolts and the bolt tapping plate.
Tighten the bolts to 10 lb-ft (14 N•m) (Figure 10-75).
NOTE: If base plate or stop plate on passenger side or spacer on drivers side were removed a sealer must be applied to prevent wa-
ter intrusion into the cabin compartment.
2.
Apply a sealing compound to the bottom of the base before securing the base to the body with the two bolts. Tighten the bolts
to 6 lb-ft (8 N•m) (Figure 10-75).
3.
Secure the rubber isolator and limiter straps to the base with the spring pin.
HOOD RELEASE CABLE ASSEMBLY REPLACEMENT
Removal
1.
Raise and secure the hood.
2.
Remove the cable handle, two nuts, lockwasher, nut and the cable assembly from the cable mounting bracket.
3.
Remove the cable assembly from the cable clamp bracket (Figure 10-77).
4.
Remove the cable assembly and the grommet from the body.
5.
Remove the lock pin from the cable assembly.
Installation
1.
Install the lock pin on the cable assembly (Figure 10-77).
2.
Secure the cable assembly to the cable clamp bracket.
BASE
ROLLER
SPACER
STOP
LIMITER
STRAP
COTTER
PIN
LATCH
BRACKET
LATCH
PLATE
TAPPING
PLATE
RUBBER
ISOLATOR
STOP
LATCH
SPRING
PIN
LATCH
PIN
10-68 Body
______________________________________________________________________
3.
Secure the cable assembly to the cable mounting bracket with the nut, lockwasher, two nuts and the cable handle (Figure
10-76).
4.
Install the grommet and the cable assembly on the body and apply sealer around the cable and the grommet.
5.
Lower the hood.
Figure 10-76: Hood Release Handle Assembly Mounting
Figure 10-77: Hood Release Cable Assembly
HANDLE
BRACKET
MOUNTING
CABLE
CABLE
ASSEMBLY
WASHER
LOCK
CABLE ASSEMBLY
GROMMET
PIN
CABLE CLAMP
BRACKET
APPLY
SEALER
BRACKET
_____________________________________________________________________
Body 10-69
Hood Release Latch and Bracket Assembly Replacement
Removal
1.
Raise and secure the hood.
2.
Remove the two bolts, lockwashers and the latch assembly from the hood (Figure 10-78).
3.
Remove the pin, spring and the lock arm from the latch assembly (Figure 10-79).
4.
Remove the cable assembly from the cable clamp bracket (Figure 10-77).
5.
Remove the three nuts, lockwashers, bolts and the bracket assembly from the body.
6.
Remove the two nuts and the lockwasher assemblies, screws and the cable clamp bracket from the bracket assembly.
Figure 10-78: Hood Release Latch and Bracket Assembly Mounting
Figure 10-79: Latch Assembly Breakdown
Installation
1.
Secure the cable clamp bracket to the bracket assembly with the two screws, nut and the lockwasher assemblies.
2.
Secure the bracket assembly to the body with the three bolts, lockwashers and the nuts.
3.
Secure the cable assembly to the cable clamp bracket. Seal the grommet with a silicone sealer (Figure 10-77).
HOOD
LATCH
PROP ROD
ASSEMBLY
SPRING
LOCK ARM
LATCH
PIN
ASSEMBLY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст