Hummer H2. Manual — part 509
9
circuit in connector C1 cavity D at the
passenger door module.
Does the test lamp illuminate?
Go to Step 10
Go to Step 18
10
1. Disconnect the passenger front power
window motor.
2. Connect a test lamp to a good ground.
3. Probe the power window motor up control
circuit at the power window motor harness
connector.
4. Activate the power window switch to the UP
position.
Does the test illuminate?
Go to Step 11
Go to Step 13
11
1. With the test lamp still connected to a good
ground, probe the power window motor
down control circuit.
2. Activate the power window switch to the
DOWN position.
Does the test lamp illuminate?
Go to Step 12
Go to Step 14
12
1. Connect a test lamp between the power
window motor up and down control circuits.
2. Activate the power window switch to the UP
and DOWN positions.
Does the test lamp illuminate in both positions?
Go to Step 17
Go to Step 15
13
Test for an open or short to ground in the power
window motor up control circuit. Refer to Circuit
Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 22
Go to Step 15
14
Test for an open or short to ground in the power
window motor down control circuit. Refer to
Circuit Testing and Wiring Repairs in Wiring
Systems.
Did you find and correct the condition?
Go to Step 22
Go to Step 15
15
Inspect for poor connections at the passenger door
module. Refer to Testing for Intermittent
Conditions and Poor Connections and
Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 22
Go to Step 19
16
Inspect for poor connections at the driver door
module. Refer to Testing for Intermittent
Conditions and Poor Connections and
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2
POWER WINDOW INOPERATIVE - PASSENGER DOOR (REAR DOOR(S))
Power Window Inoperative - Passenger Door (Rear Door(s))
Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 22
Go to Step 20
17
Inspect for poor connections at the passenger front
power window motor. Refer to Testing for
Intermittent Conditions and Poor Connections
and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 22
Go to Step 21
18
Repair the open or short to ground in the battery
positive voltage circuit. Refer to Wiring Repairs
in Wiring Systems.
Did you complete the repair?
Go to Step 22
-
19
Replace the passenger door module. Refer to
Switch Replacement - Door Lock and Side
Window - Passenger .Did you complete the
repair?
IMPORTANT:
Perform the set up procedure for the passenger
door module. Refer to Service Programming
System (SPS) in Programming.
Go to Step 22
-
20
Replace the driver door module. Refer to Switch
Replacement - Door Lock and Side Window -
Driver .Did you complete the repair?
IMPORTANT:
Perform the set up procedure for the driver door
module. Refer to Service Programming System
(SPS) in Programming.
Go to Step 22
-
21
Replace the passenger front power window motor.
Refer to Window Regulator Motor Replacement
- Front Door .
Did you complete the repair?
Go to Step 22
-
22
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 3
Step
Action
Yes
No
Schematic Reference:Power Window Schematics
Connector End View Reference:Power Door Systems Connector End Views
1
Did you perform the Door Systems Diagnostic
System Check?
Go to Step 2
Go to Diagnostic
System Check -
Door Systems
1. Disable the window lockout function.
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2
2
2. Operate the passenger rear power windows in
the UP and DOWN directions from the
passenger power window switches.
Do the passenger rear power windows operate
properly?
Go to Step 3
Go to Step 4
3
Operate the passenger rear power windows in the
UP and DOWN directions from the master
switches.
Do the passenger rear power windows operate
properly from the master switches?
Go to Testing for
Intermittent Conditions
and Poor Connections in
Wiring Systems
Go to Step 6
4
Are both rear power windows inoperative?
Go to Step 5
Go to Step 9
5
1. Install a scan tool.
2. Monitor the window lockout data parameter
in the driver door module input list.
3. Place the window lockout switch in both the
ON and OFF positions.
Does the window lockout data parameter change
accordingly?
Go to Step 23
Go to Step 24
6
1. Install a scan tool.
2. Monitor the rear window status data
parameters in the driver door module inputs
list.
Do either of the rear window status data parameters
display an active state without a rear window switch
activation?
Go to Step 24
Go to Step 7
7
1. Install a scan tool.
2. Monitor the rear window status data
parameters in the driver door module inputs
list.
3. Activate the passenger rear power window
switches on the master switch in the up and
down positions.
Do the rear window status data parameters change
accordingly?
Go to Step 8
Go to Step 24
8
1. With a scan tool, monitor the passenger rear
window status data parameters in the body
control module data list.
2. Activate the passenger rear power window
switches on the master switch in the up and
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2
down positions.
Do the rear window status data parameters change
accordingly?
Go to Step 16
Go to Step 23
9
1. Disable the window lockout function.
2. Disconnect the inoperative rear window
switch.
3. Connect a test lamp to a good ground.
4. Probe the window lockout signal circuit at the
rear window switch harness connector.
Does the test lamp illuminate?
Go to Step 10
Go to Step 18
10
With a test lamp connected to a good ground, probe
the battery positive voltage circuit at the rear power
window switch harness connector.
Does the test lamp illuminate?
Go to Step 11
Go to Step 27
11
1. Connect a test lamp to battery positive
voltage.
2. Probe the ground circuit at the rear power
window switch harness connector.
Does the test lamp illuminate?
Go to Step 13
Go to Step 28
12
Probe the power window up and down signal
circuits one at a time, with a test lamp that is
connected to the battery positive voltage.
Does the test lamp illuminate at either signal
circuit?
Go to Step 19
Go to Step 13
13
1. Disconnect the appropriate rear power
window motor.
2. Connect the rear power window switch.
3. Connect a test lamp to a good ground.
4. Probe the power window motor up control
circuit at the power window motor harness
connector.
5. Activate the power window switch to the UP
position.
Does the test illuminate?
Go to Step 14
Go to Step 21
14
1. With the test lamp still connected to a good
ground, probe the power window motor down
control circuit.
2. Activate the power window switch to the
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст