Hummer H2. Manual — part 226
Fig. 2: Steering Wheel & Column Sub-System Component Views
Courtesy of GENERAL MOTORS CORP.
Callouts For Fig. 2
Callout
Component Name
1
Steering Wheel Audio Controls - Left
2
Passlock Sensor Connector
3
Ignition Key Alarm Switch
4
Ignition Lock Cylinder Control Actuator
5
Ignition Lock Cylinder Control Actuator Connector
6
Ignition Switch
7
Ignition Key Cylinder
8
Steering Wheel Audio Controls - Right
9
Horn Switch
10
Steering Wheel Driver Information (DIC) Controls - Right
11
C277
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
CRUISE CONTROL CONNECTOR END VIEWS
Turn Signal/Multifunction Switch - Terminal Identification - C4
DIAGNOSTIC INFORMATION AND PROCEDURES
DIAGNOSTIC STARTING POINT - CRUISE CONTROL
Begin the system diagnosis with theDiagnostic System Check - Cruise Control . The Diagnostic System
Check will provide the following information:
z
The identification of the control modules which command the system
z
The ability of the control modules to communicate through the serial data circuit
z
The identification of any stored diagnostic trouble codes (DTCs) and their status
The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and
where the procedure is located.
DIAGNOSTIC SYSTEM CHECK - CRUISE CONTROL
12
Steering Wheel Driver Information Center (DIC) Controls - Left
13
Turn Signal/Multifunction Switch
Connector Part Information
z
12047786
z
4-Way M Metri-Pack 150 Series (BK)
Pin
Wire Color
Circuit No.
Function
A
BN
41
Ignition 3 Voltage
B
GY/WH
397
Cruise Control On Switch Signal
C
GY/BK
87
Cruise Control Resume/Accel Switch Signal
D
D-BU
84
Cruise Control Set/Coast Switch Signal
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
Description
The Cruise Control Diagnostic System Check is an organized approach to identifying a condition created by an
electronic control system failure. The Diagnostic System Check directs the service technician to the next logical
step in diagnosing the concern. Understanding the system, the table, and using it correctly reduces diagnostic
time and prevents misdiagnosis. For a review of the cruise control system, refer to Cruise Control Description
and Operation .
Test Description
The numbers below refer to the step numbers on the diagnostic table.
2: Lack of communication may be due to a malfunction in the class 2 serial data circuit. The specified
procedure will determine the particular condition.
5: The presence of DTCs which begin with "U" indicates that some other module is not communicating.
The specified procedure will compile all the available information before tests are performed.
Diagnostic System Check - Cruise Control
Step
Action
Yes
No
1
Install a scan tool.
Does the scan tool power up?
Go to Step 2
Go to Scan Tool Does Not
Power Up in Data Link
Communications
2
1. Turn the ignition ON, with the
engine OFF.
2. Attempt to establish
communication with the
following modules:
z
Powertrain Control
Module (PCM)
z
Electronic Brake Control
Module (EBCM)
Does the scan tool communicate with
the modules listed above?
Go to Step 3
Go to Scan Tool Does Not
Communicate with Class 2
Device in Data Link
Communications
3
1. With a scan tool, access the Class
2 Power Mode in the Diagnostic
Circuit Check.
2. Rotate the ignition switch
through all positions while
IMPORTANT:
The engine may start during the
following step. Turn the engine OFF
as soon as you have observed the
Crank power mode.
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
SCAN TOOL DATA LIST
Powertrain (PCM)
observing the System Power
Mode parameter.
Does the System Power Mode
parameter reading match the ignition
switch position for all switch positions?
Go to Step 4
Go to Power Mode
Mismatch in Body Control
System
4
Select the DTCs function on the scan
tool for the following modules:
z
Powertrain Control Module
(PCM)
z
Electronic Brake Control Module
(EBCM)
Does the scan tool display any DTCs?
Go to Step 5
Go to Symptoms - Cruise
Control
5
Does the scan tool display any DTCs
which begin with a "U"?
Go to Scan Tool Does Not
Communicate with Class 2
Device in Data Link
Communications
Go to Step 6
6
Does the scan tool display DTC P0562,
P0563, P0615, P1637, or P01638?
Go to Diagnostic Trouble
Code (DTC) List in Engine
Electrical
Go to Diagnostic Trouble
Code (DTC) List
Scan Tool Parameter
Data List
Units Displayed
Typical Data
Value
The Ignition is ON/Engine Idling at Normal Operating Temperature/Transmission is in
Park/Cruise Control On/Off Switch is Off
Cruise Control Active
Cruise Control
Data
Yes/No
No
Cruise Disengage (1 - 8)
History
Cruise Control
Data
Last reason for cruise control
disengagement
Varies
Cruise On/Off Switch
Cruise Control
Data
On/Off
Off
Cruise Release Brake Pedal
Switch
Cruise Control
Data
Applied/Released
Released
Cruise Resume/Accel. Switch
Cruise Control
Data
On/Off
Off
Cruise Set/Coast Switch
Cruise Control
Data
On/Off
Off
Engine Speed
Cruise Control
RPM
Varies
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст