Hummer H2. Manual — part 227
SCAN TOOL DATA DEFINITIONS (CRUISE CONTROL)
The Scan Tool Data Definitions contains a brief description of all cruise control related parameters available on
the scan tool.
Cruise Control Active
The scan tool displays Yes or No. The PCM determines the current status of cruise control operation. An
active cruise control system is displayed as Yes.
Cruise Disengage (1 - 8) History
The scan tool displays the last 8 reasons why the cruise control system was disengaged. Refer to the Scan
Tool Data Definitions (Disengaged History) for descriptions.
Cruise On/Off Switch
The scan tool displays On or Off. The TAC module monitors the signal circuit of the On/Off switch of
the cruise control system. A closed switch is displayed as On.
Cruise Release Brake Pedal Switch
The scan tool displays Applied or Released. The PCM monitors the TCC brake switch/Cruise control
release signal circuit. An open switch is displayed as Applied.
Cruise Resume/Accel. Switch
The scan tool displays On or Off. The TAC Module monitors the signal circuit of the Resume/Accel.
switch of the cruise control system. A closed switch is displayed as On.
Cruise Set/Coast Switch
Data
Ignition 1 Signal
Cruise Control
Data
Volts
Varies
Reduced Engine Power
Cruise Control
Data
Active/Inactive
Inactive
Stoplamp Pedal Switch
Cruise Control
Data
Applied/Released
Released
TAC/PCM Communication
Signal
Cruise Control
Data
OK/Fault
OK
Traction Control Signal
Cruise Control
Data
Active/Inactive
Inactive
Vehicle Speed Sensor
Cruise Control
Data
km/h (mph)
0 km/h (0 mph)
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
The scan tool displays On or Off. The TAC module monitors the signal circuit of the Set/Coast switch of
the cruise control system. A closed switch is displayed as On. The cruise On/Off switch must be switched
On in order to correctly view the Cruise Set/Coast Switch parameter.
Engine Speed
The scan tool displays 0 to 9,999 RPM. The PCM monitors the CKP signal circuit in order to determine
the engine RPM.
Ignition 1 Signal
The scan tool displays 6 Volts to 18 Volts. The PCM monitors the Ignition 1 signal circuit in order to
determine the system voltage.
Reduced Engine Power
The scan tool displays Active or Inactive. When the PCM determines that a throttle actuator control
system malfunction exists, the scan tool displays Active.
TAC/PCM Communication Signal
The scan tool displays OK or Fault. The PCM uses the UART serial data circuit in order to communicate
with the TAC module. If the communication between the PCM and the TAC module is interrupted, the
scan tool displays Fault.
Traction Control Signal
The scan tool displays Active or Inactive. When the PCM receives a class 2 signal from the Electronic
Brake Control Module requesting a traction control related function, the scan tool displays Active.
Stoplamp Pedal Switch
The scan tool displays Applied or Released. The PCM monitors the stop lamp switch signal circuit. A
closed switch is displayed as Applied.
Vehicle Speed Sensor
The scan tool displays 0 to 150 km/h (93.2 mph). The PCM monitors the vehicle speed sensor signal
circuit in order to calculate the vehicle speed for display.
SCAN TOOL DATA DEFINITIONS (DISENGAGE HISTORY)
The Cruise Control Scan Tool Definitions - Disengage History is a common list for all of the available cruise
control disengagement definitions available on the scan tool. The cruise control system equipped on the vehicle
determines which cruise control disengagement parameters are available on the scan tool.
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
One of the following conditions must be present in order for a disengagement parameter to appear:
z
The cruise control system is active and disengagement is requested.
z
The engagement of the cruise control system is requested while a fault is present.
Accel Rate
The PCM/ECM detects that the vehicle acceleration is greater than the calibrated cruise control threshold.
Bad Sequence
The PCM/ECM detects that a cruise control software execution error is present.
Brake
The PCM/ECM detects that the stop lamps have been activated or the PCM/ECM detects that a stop lamp
pedal activation had not occurred before the cruise control system was requested.
Cancel
The PCM/ECM detects that the cruise control cancel switch has been activated.
CC Sw. Position
The PCM/ECM detects that the acceleration mode is active without the activation of the Accel. switch.
Clutch
The PCM/ECM detects that the clutch pedal switch has been activated.
Clutch Switch
The PCM/ECM detects that the clutch pedal switch has been activated.
Cruise Off
The PCM/ECM detects that the cruise On/Off switch was turned to Off when the cruise control system
was enabled.
Coast Low Speed
The PCM/ECM detects that the Set/Coast switch is activated until the vehicle speed is below 37 km/h (23
mph).
Coast Disengage
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
When the PCM/ECM detects that the cruise set/coast signal is active and the throttle blade fully closes the
cruise control system will disengage until the PCM/ECM detects that the set/coast signal is inactive. The
cruise control system will then engage and set with the new vehicle speed.
Decel Rate
The PCM/ECM detects that the vehicle deceleration is greater than the calibrated cruise control threshold.
DTC Set
The PCM/ECM detects that a DTC has been set which affects the cruise control operation.
Engine Run Time
The PCM/ECM detects that the cruise control system has been requested and the engine run time counter
is not active.
Engine Speed
The PCM/ECM detects that the engine speed is less than or greater than a calibrated RPM.
ETC
The PCM/ECM detects a fault within the TAC system.
First Gear
While the cruise control system is active, the PCM/ECM detects that the transmission is in Drive 1.
High Accel.
The PCM/ECM detects that the vehicle acceleration is greater than the calibrated cruise control threshold.
High Decel.
The PCM/ECM detects that the vehicle deceleration is greater than the calibrated cruise control threshold.
High Speed
The PCM/ECM detects that the vehicle speed is greater than the calibrated amount.
Illegal Mode
The PCM/ECM detects that the acceleration mode is active without the activation of the Accel. switch.
Injector Disable
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст