Hummer H2. Manual — part 186
Action Taken When the DTC Sets
The BCM implements default actions for each ignition switch position when faults are detected.
Conditions for Clearing the DTC
z
A current DTC clears when the malfunction is no longer present.
z
A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat
of the malfunction.
DTC B1440
Active
On
Off
No
Inactive
On
Off
Yes
Inactive
1
On
On
Yes
Active
Off
Off
Yes
Active
Off
On
Yes
Active
On
Off
Yes
1
The module sets the DTC 1 minute after it detects the condition.
Step
Action
Yes
No
Schematic Reference:Body Control System Schematics
Connector End View Reference: Body Control System Connector End Views
1
Perform the Diagnostic System Check for the system exhibiting the
symptom. Refer to Control Module References .
Did you perform the Diagnostic System Check?
Go to
Step 2
Go to Control
Module
References
2
1. Install a scan tool.
2. Turn OFF the ignition.
3. With a scan tool, monitor the following in Body Control Module,
Data Display, Inputs:
z
Ignition 0
z
Ignition 1
z
Ignition Accessory
Does the scan tool indicate that all inputs are inactive/Off?
Go to
Step 3
Go to Step 6
3
1. Install a scan tool.
2. Turn the ignition switch to ACC.
3. With a scan tool, monitor the following in Body Control Module,
Data Display, Inputs:
z
Ignition 0
z
Ignition 1
z
Ignition Accessory
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Body Control System - Hummer H2
Does the scan tool indicate that the Ignition 0 and Ignition Accessory
inputs are active/On?
Go to
Step 4
Go to Step 8
4
1. Turn the ignition switch ON, with the engine OFF.
2. With a scan tool, monitor the following in Body Control Module,
Data Display, Inputs:
z
Ignition 0
z
Ignition 1
z
Ignition Accessory
Does the scan tool indicate that the all inputs are active/On?
Go to
Step 5
Go to Step 8
5
1. Turn the ignition switch to START.
2. With a scan tool, monitor the following in Body Control Module,
Data Display, Inputs:
z
Ignition 0
z
Ignition 1
z
Ignition Accessory
Does the scan tool indicate that the Ignition 0 and Ignition 1 inputs are
On and the Ignition Accessory input is inactive?
IMPORTANT:
The engine may start in this step. Turn the engine OFF immediately
after reviewing the input data.
Go to
Step
11
Go to Step 8
6
1. Disconnect the ignition switch harness connectors.
2. With a scan tool, monitor the following in Body Control Module,
Data Display, Inputs:
z
Ignition 0
z
Ignition 1
z
Ignition Accessory
Does the scan tool indicate that any of the Ignition 0, Ignition 1 or
Ignition Accessory inputs is active/On?
Go to
Step 7
Go to Step 9
7
1. Disconnect the body control module (BCM) harness connectors.
2. Test the suspect ignition switch input circuits for a short to
voltage. Refer to Circuit Testing and Wiring Repairs in Wiring
Systems.
Did you find and correct the condition?
Go to
Step
14
Go to Step 11
1. Disconnect the ignition switch connectors.
2. Install a 3A fused jumper between the suspect circuits and an
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Body Control System - Hummer H2
DTC C0550
Circuit Description
The internal fault detection is handled inside the control module. No external circuits are involved.
8
ignition switch B+ supply.
3. With a scan tool, monitor the suspect circuits in Body Control
Module, Data Display, Inputs:
z
Ignition 0
z
Ignition 1
z
Ignition Accessory
Does the scan tool indicate that the suspect circuits are now active/On?
Go to
Step 9
Go to Step 10
9
Inspect for poor connections at the ignition switch harness connectors.
Refer to Testing for Intermittent Conditions and Poor Connections
andConnector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to
Step
14
Go to Step 12
10
1. Disconnect the BCM harness connectors.
2. Test the suspect ignition switch input circuits for a short to
ground or an open. Refer to Circuit Testing andWiring Repairs
in Wiring Systems.
Did you find and correct the condition?
Go to
Step
14
Go to Step 11
11
Inspect for poor connections at the BCM harness connectors. Refer to
Testing for Intermittent Conditions and Poor Connections and
Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to
Step
14
Go to Step 13
12
Replace the ignition switch. Refer to Ignition Switch Replacement in
Steering Wheel and Column.
Did you complete the replacement?
Go to
Step
14
-
13
Replace the BCM. Refer to Body Control Module Replacement .Did
you complete the replacement?
IMPORTANT:
Perform the programming or setup procedure for the module, if
required.
Go to
Step
14
-
14
1. Reconnect all components.
2. Use the scan tool in order to clear DTCs.
3. Operate the vehicle within the Conditions for Running the DTC
as specified in the supporting text.
Does the DTC reset?
Go to
Step 2
System OK
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Body Control System - Hummer H2
Conditions for Running the DTC
The microprocessor runs the program to detect an internal fault when power up is commanded. The only
requirements are voltage and ground. This program runs even if the voltage is out of the valid operating range.
Conditions for Setting the DTC
z
The control module detects an internal write malfunction.
z
The control module detects an internal checksum malfunction.
Action Taken When the DTC Sets
If equipped, the following module specific actions may occur:
z
The ABS indicator turns ON.
z
The BRAKE Warning indicator turns ON.
z
The TCS indicator turns ON.
z
The EBCM disables the ABS/DRP/TCS.
Conditions for Clearing the DTC
z
A current DTC clears when the malfunction is no longer present.
z
A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat
of the malfunction.
Diagnostic Aids
z
This DTC may be stored as a history DTC without affecting the operation of the module. If stored only as
a history DTC and not retrieved as a current DTC, do not replace the module.
z
If this DTC is retrieved as both a current and history DTC, replace the module.
z
If this DTC continues to set intermittently, replace the module
DTC C0550
Step
Action
Yes
No
1
Did you perform the Diagnostic System Check for the
system exhibiting the symptom?
Go to
Step 2
Go to Control Module
References for the applicable
Diagnostic System Check
2
1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Retrieve DTCs.
Is the DTC retrieved as a current DTC?
Go to
Step 3
Go to Diagnostic Aids
IMPORTANT:
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Body Control System - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст