Hummer H2. Manual — part 506

Conditions for Clearing the DTC

When the fault is no longer present, the BCM changes the current DTC to a history DTC. The BCM will clear
the history DTC after 50 fault free ignition cycles.

DTC B3824

Step

Action

Yes

No

Schematic Reference: Power Window Schematics
Connector End View Reference:Power Door Systems Connector End Views

1

Did you perform the Door Systems Diagnostic
System Check?

Go to Step 2

Go to Diagnostic

System Check -

Door Systems

2

1. Install a scan tool.

2. Turn ON the ignition, with the engine OFF.

3. Disable the window lockout function.

4. With a scan tool, command the right rear

power window UP and DOWN.

Does the right rear power window operate UP and
DOWN with each command?

Go to Testing for

Intermittent Conditions

and Poor Connections in

Wiring Systems

Go to Step 3

3

1. Turn OFF the ignition.

2. Disconnect the right rear power window

switch.

3. Turn ON the ignition, with the engine OFF.

4. Ensure the window lockout function is

disabled.

5. Probe the window lockout signal circuit with

a test lamp connected to a good ground.

Does the test lamp illuminate?

Go to Testing for

Intermittent Conditions

and Poor Connections in

Wiring Systems

Go to Step 4

4

Test the window lockout signal circuit for a short to
ground. Refer to Circuit Testing and Wiring
Repairs in Wiring Systems.
Did you find and correct the condition?

Go to Step 7

Go to Step 5

5

Inspect for poor connections at the harness
connector of the Body Control Module. Refer to
Testing for Intermittent Conditions and Poor
Connections and Connector Repairs in Wiring
Systems.
Did you find and correct the condition?

Go to Step 7

Go to Step 6

IMPORTANT:

Perform the set up procedure for the Body
Control Module.

2004 Hummer H2

2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2

DTC B3825

Circuit Description

The body control module (BCM) internally grounds the liftgate lock relay control circuit for the liftgate lock
relay when it receives a Class 2 message from the driver door module (DDM), passenger door module (PDM),
or when a liftgate lock function is activated. When the BCM grounds the liftgate lock relay control circuit the
liftgate lock relay is energized and locks the liftgate.

Conditions for Running the DTC

z

Battery voltage is between 9.0-16.0 volts.

z

The DTC will set if the liftgate lock function is active or inactive.

Conditions for Setting the DTC

The DTC will set if the liftgate lock relay control circuit is shorted to ground or open for more then one second.

Action Taken When the DTC Sets

z

If a short to ground is present on the liftgate lock relay control circuit, the liftgate lock relay will be
energized and the liftgate lock actuator will be held in the lock position and will not unlock.

z

If an open condition is present on the liftgate lock relay control circuit, the liftgate will unlock but not
lock.

z

The BCM will send a Class 2 message to the DIC indicating that a fault has been detected and the DIC
will display REPLACE LIFTGATE FUSE.

Conditions for Clearing the DTC

When the fault is no longer present, the BCM changes the current DTC to a history DTC. The BCM will clear
the history DTC after 50 fault free ignition cycles.

Diagnostic Aids

DTC B3825 will set as current if any of the following conditions are present:

6

Replace the Body Control Module. Refer to Body
Control Module Replacement in Body Control
System.Did you complete the replacement?

Go to Step 7

-

7

1. Use the scan tool in order to clear the DTCs.

2. Operate the vehicle within the Conditions for

Running the DTC as specified in the
supporting text.

Does the DTC reset?

Go to Step 2

System OK

2004 Hummer H2

2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2

z

An open ECC fuse

z

An open or short to ground in the liftgate lock relay battery positive voltage circuit

z

A faulty liftgate lock relay

z

An open or short to ground in the liftgate lock relay control circuit

z

A short to ground in the liftgate lock actuator lock control circuit will open the ECC with a lock
command

z

A faulty BCM

Test Description

The numbers below refer to the step numbers on the diagnostic table.

2: Command both the Lock and Unlock states. Repeat the commands as necessary.

3: Tests for voltage at the coil side of the liftgate lock relay. The ECC fuse supplies power to the coil side
of the liftgate lock relay.

4: Verifies that the body control module is providing ground to the liftgate lock relay.

5: Tests if ground is constantly being applied to the liftgate lock relay.

DTC B3825

Step

Action

Yes

No

Schematic Reference: Door Lock/Indicator Schematics
Connector End View Reference: Power Door Systems Connector End Views

1

Did you perform the Door Systems Diagnostic
System Check?

Go to Step 2

Go to Diagnostic

System Check -

Door Systems

2

1. Install a scan tool.

2. With a scan tool, command the rear doors to

Lock and Unlock.

Does the liftgate Lock and Unlock with each
command?

Go to Testing for

Intermittent Conditions

and Poor Connections in

Wiring Systems

Go to Step 3

3

1. Remove the liftgate lock relay.

2. Probe the battery positive voltage circuit of

the liftgate lock relay with a test lamp that is
connected to a good ground.

Does the test lamp illuminate?

Go to Step 4

Go to Step 8

4

1. Connect a test lamp between the liftgate lock

relay control circuit and the battery positive
voltage circuit of the liftgate lock relay.

2. With a scan tool, command the rear doors to

Lock and Unlock.

2004 Hummer H2

2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2

Does the test lamp turn ON and OFF with each
command?

Go to Step 9

Go to Step 5

5

Does the test lamp remain illuminated without being
commanded?

Go to Step 7

Go to Step 6

6

Test the liftgate lock relay control circuit of the
liftgate lock relay for an open. Refer to Circuit
Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?

Go to Step 14

Go to Step 10

7

Test the liftgate lock relay control circuit of the
liftgate lock relay for a short to ground or an open.
Refer to Circuit Testing and Wiring Repairs in
Wiring Systems.
Did you find and correct the condition?

Go to Step 14

Go to Step 10

8

Test for an open or short to ground in the battery
positive voltage circuit of the liftgate lock relay.
Refer to Circuit Testing and Wiring Repairs in
Wiring Systems.
Did you complete the repair?

Go to Step 14

Go to Step 11

9

Inspect for poor connections at the liftgate lock
relay. Refer to Testing for Intermittent
Conditions and Poor Connections and Connector
Repairs in Wiring Systems.
Did you find and correct the condition?

Go to Step 13

Go to Step 12

10

Inspect for poor connections at the harness
connector of the body control module (BCM). Refer
to Testing for Intermittent Conditions and Poor
Connections and Connector Repairs in Wiring
Systems.
Did you find and correct the condition?

Go to Step 14

Go to Step 13

11

Repair the short to ground in the liftgate lock
actuator lock control circuit. Refer to Wiring
Repairs in Wiring Systems.
Did you complete the repair?

Go to Step 14

-

12

Replace the liftgate lock relay.
Did you complete the replacement?

Go to Step 14

-

13

Replace the BCM. Refer to Body Control Module
Replacement in Body Control System.Did you
complete the replacement?

IMPORTANT:

Perform the set up procedure for the BCM.

Go to Step 14

-

14

1. Use the scan tool in order to clear the DTCs.

2. Operate the vehicle within the Conditions for

Running the DTC as specified in the

2004 Hummer H2

2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2