Hummer H2. Manual — part 1157
Fig. 4: Top Of Steering Column Component Views
Courtesy of GENERAL MOTORS CORP.
Callouts For Fig. 4
ENGINE ELECTRICAL CONNECTOR END VIEWS
Generator Terminal Identification
Callout
Component Name
1
Ignition Switch
2
Passlock Sensor
3
Ignition Key Alarm Switch
4
Ignition Lock Cylinder Control Actuator
5
Steering Column
2004 Hummer H2
2004 ELECTRICAL Engine Electrical - Hummer H2
Ignition Terminal Identification Switch
Connector Part Information
z
15355066
z
2-Way F Metri-Pack 150 Series Sealed (TN)
Pin
Wire Color
Circuit No.
Function
A
-
-
Plugged
B
BN
25
Charge Indicator Control Signal
C
GY
23
Generator Field Duty Cycle Signal
D
-
-
Plugged
Connector Part Information
z
10400853490
z
7-Way F Kostal N Series (BK)
Pin
Wire Color
Circuit No.
Function
2004 Hummer H2
2004 ELECTRICAL Engine Electrical - Hummer H2
DIAGNOSTIC INFORMATION AND PROCEDURES
DIAGNOSTIC STARTING POINT - ENGINE ELECTRICAL
Begin the system diagnosis with the Diagnostic System Check - Engine Electrical . The Diagnostic System
Check will provide the following information:
z
The identification of the control module(s) which command the system.
z
The ability of the control module(s) to communicate through the serial data circuit.
z
The identification of any stored diagnostic trouble codes (DTCs) and their status.
The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and
where the procedure is located.
DIAGNOSTIC SYSTEM CHECK - ENGINE ELECTRICAL
Diagnostic System Check - Engine Electrical
A
BN
4
Accessory Voltage
B
RD/WH
342
Battery Positive Voltage
C
PK
3
Ignition 1 Voltage
D
YE
5
Crank Voltage
E
WH
1390
Acc/Run/Crank Voltage
F
RD
142
Battery Positive Voltage
G
OG
300
Ignition 3 Voltage
Step
Action
Yes
No
1
Did you perform the Battery Inspection/Test?
Go to Step 2
Go to Battery
Inspection/Test (Non-HP2)
2
Install a scan tool.
Does the scan tool power up?
Go to Step 4
Go to Scan Tool Does Not
Power Up
3
1. Access the Class 2 Power Mode in the
Diagnostic Circuit Check on the scan tool.
2. Rotate the ignition switch through all
positions while observing the ignition
switch power mode parameter.
Does the ignition switch parameter reading
match the ignition switch position for all switch
positions?
IMPORTANT:
The engine may start during the following
step. Turn OFF the engine as soon as you
have observed the Crank power mode.
Go to Step 4
Go to Power Mode
Mismatch in Body Control
System
2004 Hummer H2
2004 ELECTRICAL Engine Electrical - Hummer H2
SCAN TOOL DATA LIST
Powertrain Control Module (PCM)
SCAN TOOL DATA DEFINITIONS
4
1. Turn ON the ignition, with the engine
OFF.
2. Attempt to communicate with each
module on the class 2 serial data circuit.
If using a Tech 2, obtain this information
using the Class 2 Message Monitor
feature.
Does the scan tool communicate with any
module on the class 2 serial data circuit?
Go to Step 5
Go to Scan Tool Does Not
Communicate with Class 2
Device
5
1. Select the Display DTCs function for each
module.
If using a Tech 2, use the Class 2 DTC
Check feature in order to determine which
modules have DTCs set.
2. Record all of the displayed DTCs the
DTC status and the module which set the
DTC.
Does the scan tool display any DTCs?
Go to Step 6
Go to Symptoms - Engine
Electrical
6
Does the scan tool display any DTC beginning
with "U"?
Go to Diagnostic
Trouble Code
(DTC) List
Go to Step 7
7
Does the scan tool display any DTC beginning
with "P"?
Go to Powertrain
DTC list in Engine
Controls
Go to Step 8
8
Does the scan tool display any DTC beginning
with "B"?
Go to Diagnostic
Trouble Code
(DTC) List
Go to Diagnostic Trouble
Code (DTC) List
Scan Tool Parameter
Data List
Units Displayed
Typical Data Value
Ignition ON/Engine OFF
Ignition 1 Signal
Engine 1,2 Data
Volts
9-14v
GEN L-Terminal Signal Command
Engine 2 Data
OK/No Output
OK
GEN F-Terminal Signal
Engine 2 Data
%
10-90%
2004 Hummer H2
2004 ELECTRICAL Engine Electrical - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст