Toyota Proace City (2022 year). Manual in english — page 3
40
With side-hinged doors
- when the vehicle is stationary and engine
► Then press this button again within five
running, this warning lamp comes on,
seconds after locking.
accompanied by a warning message for a few
seconds,
With the Keyless Entry and Starting
- when the vehicle is moving (at speeds above
on your person
10 km/h (6 mph)), this warning lamp comes on,
accompanied by an audible signal and a warning
message for a few seconds.
Deadlocking
► To lock the vehicle, with the remote control
► To lock the vehicle, with the remote control
in recognition zone A, press the left-hand door
in recognition zone A, press on the markings of
locking control.
one of the front or rear door handles.
WARNING
► To deadlock the vehicle, press the marking
NOTICE
again within five seconds.
Deadlocking renders the exterior and interior
With side-hinged doors
If your vehicle is fitted with an alarm, pressing
door controls inoperative.
and holding the locking button enables the
It also deactivates the manual central control
windows to be closed. The window stops in
button.
position when you release the button.
The horn remains operational.
Therefore, never leave anyone inside the
vehicle when it is deadlocked.
WARNING
Driving with the doors locked could make it
With the key
more difficult for the emergency services to
► To deadlock the vehicle, turn the key in the
enter the vehicle in an emergency.
driver's door lock towards the rear of the vehicle.
As a safety measure, never leave the vehicle,
► To lock the vehicle, with the remote control
► Then within five seconds, turn the key
even for a short time, without taking the
in recognition zone A, press the left-hand door
towards the rear again.
remote control with you.
locking control.
► To deadlock the vehicle, press the control
With the remote control
If a door is not properly closed (except the
again within five seconds.
► To deadlock the vehicle, press this
right-hand door with side-hinged rear
button.
doors):
41
Back-up procedures
Central locking not
NOTICE
functioning
If the vehicle is fitted with an alarm, it will not
Lost keys, remote control,
Use these procedures in the following cases:
be activated when locking with the key.
electronic key
- Central locking malfunction.
If the alarm is activated, the siren sounds
- Battery disconnected or discharged.
Go to a TOYOTA dealer with the vehicle's
when the door is opened; switch on the
2
registration certificate, your personal
ignition to stop it.
WARNING
identification documents and if possible, the label
bearing the key code.
In the event of a malfunction of the central
The TOYOTA dealer will be able to retrieve the
locking system, the battery must be
key code and the transponder code, enabling a
disconnected to ensure that the vehicle is
new key to be ordered.
NOTICE
locked fully.
Complete unlocking/locking
If the vehicle is unlocked with the key in the
lock after locking it with the remote control
Locking part of the vehicle (front
of the vehicle with the key
or the Keyless Entry and Starting system,
passenger door/sliding side door/
Use this procedure in the following situations:
all doors and the boot are unlocked.
side-hinged doors)
- Remote control battery discharged.
If the vehicle is unlocked with the key in the
- Remote control malfunction.
► With a sliding side door or side-hinged
lock after locking it with the key, only the
- Vehicle battery discharged.
doors, if fitted to your vehicle, check that the
doors (front door and sliding side door(s))
- Vehicle in an area subject to strong
electric child lock is not activated.
are unlocked. The swing doors and tailgate
electromagnetic interference.
► Open the door.
are not unlocked. They can be unlocked after
In the first case, change the remote control
switching on the ignition.
battery.
In the second case, reinitialise the remote
control.
Refer to the corresponding sections.
► Insert the key in the left front door lock.
► Turn the key towards the front/rear to unlock/
Front door
lock the vehicle.
► Turn the key towards the rear again within
5 seconds to deadlock the vehicle.
42
NOTICE
WARNING
For more information on the Child lock on a
In the event of a malfunction or if you
sliding side door or side-hinged doors,
experience difficulty opening or closing the
Sliding side door
refer to the corresponding section.
tailgate, have it checked by a TOYOTA dealer
or a qualified workshop without delay, to avoid
the issue deteriorating and prevent any risk of
Unlocking the tailgate
the tailgate dropping, potentially causing
serious injury.
Changing the battery
If the battery is flat, this warning lamp
comes on, accompanied by an audible
Side-hinged doors
signal and the display of a message.
► Remove the cap located on the edge of the
Battery type: CR2032/3 volts.
door.
► From inside the vehicle, insert a small
► Insert the integral key into the latch (without
Without Keyless Entry and Starting
screwdriver into hole A on the lock to unlock the
forcing) and then turn the assembly.
tailgate.
► Remove the key and refit the cap.
► Move the latch to the left.
► Close the door(s) and check from the outside
that the vehicle is locked correctly.
Unlocking of one part of the vehicle
(front passenger door/sliding side
NOTICE
door/side-hinged doors)
If the battery is discharged and your vehicle is
► Use the interior opening handle.
equipped with a tailgate and an Extenso
or
cabin, you will not be able to access the
► With side-hinged doors, insert the integral
loading area.
key in the (left-hand) door lock, then turn it.
Replace the battery to regain access.
For more information on the 12 V battery,
refer to the corresponding section.
43
With Keyless Entry and Starting
WARNING
WARNING
This equipment contains a button type
Risk of explosion or leaking of inflammable
battery.
liquid or gas!
Do not swallow the battery. Risk of chemical
Do not use in/store in/place in an environment
burns!
where the temperature is extremely high or
2
Swallowing the battery can cause serious
where the pressure is extremely low due to
internal burning in only 2 hours and can be
very high altitude.
fatal.
Do not try to burn, crush or cut a used battery.
If batteries have been swallowed or inserted
into a part of the body, seek immediate
Reinitialising the remote
medical advice.
Keep new and used batteries out of the reach
control
► Unclip the cover by inserting a small
screwdriver in the slot and lift the cover.
of children.
Following replacement of the battery or in
► Remove the flat battery from its housing.
If the battery compartment does not close
the event of a fault, it may be necessary to
► Put the new battery in place, respecting the
properly, stop using the product and keep it
reinitialise the remote control.
out of the reach of children.
polarity. Start by inserting it into the contacts
Without Keyless Entry and Starting
located in the corner, then clip the cover onto
the unit.
WARNING
► Reinitialise the remote control.
For more information on Reinitialising the
Risk of explosion if the battery is replaced
remote control, refer to the corresponding
with an incorrect type!
section.
Replace the battery with the same type.
ECO
Do not throw remote control batteries away,
as they contain metals that are harmful to the
environment. Take them to an approved
disposal point.
► Switch the ignition off.
► Turn the key to position 2 (Ignition on).
44
► Immediately press the closed padlock button
Central locking / unlocking
WARNING
for a few seconds.
This function enables the doors to be locked or
► Switch off the ignition and remove the key
Driving with the doors locked could make it
unlocked simultaneously from inside the vehicle.
from the ignition switch.
difficult for the emergency services to enter
The remote control is now fully operational
the vehicle in an emergency.
again.
NOTICE
If one of the doors is open, the central locking
from the inside does not function. This is
signalled by a mechanical noise from the
locks.
If the boot is open, only the locking of the
NOTICE
other doors is carried out. The indicator lamp
in the button remains off.
When locking/deadlocking from the
► Insert the mechanical key (incorporated into
outside
the remote control) into the lock to open the
When the vehicle is locked or deadlocked
NOTICE
vehicle.
from the outside, the indicator lamp flashes
► Place the electronic key against the back-up
and the button is deactivated.
When locking from inside, the door mirrors do
reader on the steering column and hold it there
► After normal locking, pull one of the
not fold.
until the ignition is switched on.
interior door controls to unlock the vehicle.
► With a manual gearbox, place the gear lever
► After deadlocking, you must use the
NOTICE
in neutral then fully depress the clutch pedal.
remote control, the "Keyless Entry and
► With an automatic gearbox, while in mode
Starting" system or the built-in key to unlock
The indicator lamp also goes off when
P, depress the brake pedal.
the vehicle.
unlocking one or more accesses.
► Switch on the ignition by pressing the
"START/STOP" button.
Manual mode
If the fault persists after reinitialisation, contact
Automatic mode
► Press this button to lock / unlock the
any authorized Toyota retailer or Toyota
This is the automatic central locking of the
vehicle.
authorized repairer, or any reliable repairer
vehicle when driving, also called anti-intrusion
without delay.
security.
45
For more information on Anti-intrusion
Automatic mode
NOTICE
security, refer to the corresponding section.
The loading area is always locked when driving.
For more information on the Key, and, in
Locking/unlocking the
NOTICE
particular, on programming selective locking
loading area
for the loading area, refer to the
To deactivate the automatic locking function,
corresponding section.
go to a TOYOTA dealer or a qualified
2
workshop.
Manual mode
► With complete unlocking activated,
press this button to lock (indicator lamp
Anti-intrusion security
comes on)/unlock (indicator lamp goes off) the
This system allows automatic simultaneous
vehicle.
locking of the doors and boot as soon as the
► With selective unlocking activated, press this
speed of the vehicle exceeds 10 km/h (6 mph).
button to lock (indicator lamp comes on)/unlock
(indicator lamp goes off) the loading area.
Operation
WARNING
If one of the doors or the boot is open, the
automatic central locking does not take place.
Driving with the doors locked could make it
This is signalled by the sound of the locks
NOTICE
more difficult for the emergency services to
rebounding, accompanied by illumination
enter the vehicle in an emergency.
of this warning lamp in the instrument panel, an
This button is unavailable if the vehicle has
audible signal and the display of an alert
been locked or deadlocked from outside
message.
(using the key, remote control or Keyless
NOTICE
Entry and Starting, depending on equipment)
or if any of the doors are still open.
The indicator lamp goes off when unlocking
one or more doors of the loading area.
With the ignition off and the vehicle fully
locked, the indicator lamp goes off for energy
economy reasons.
46
Activation/Deactivation
Side-hinged doors
Opening to approximately 180°
You can activate or deactivate this function
Keeping the left-hand door closed with the
permanently.
right-hand door open
► With the ignition on, press the central locking
button until an audible signal is triggered and
a corresponding message of confirmation is
displayed.
The state of the system stays in the memory
when the ignition is switched off.
If fitted to your vehicle, a check strap system
WARNING
allows the doors to be opened from about 90° to
about 180°.
Driving with the doors locked may render
► Pull the yellow control when the door is open.
access by the emergency services to the
NOTICE
The check strap will engage again automatically
interior difficult in an emergency.
on closing.
It is possible to drive with the right-hand door
open, to enable the transportation of long
NOTICE
loads.
The left-hand door is kept closed by the
Carrying long or voluminous objects
distinctive "yellow" lock, positioned at the
If you want to drive with the boot open, you
base of the door.
should press the central locking button to lock
This closed door must not be used to retain
the doors. Otherwise, every time the speed
loads.
of the vehicle exceeds 10 km/h (6 mph), the
Driving with the right-hand door open is a
locks will rebound and the alerts mentioned
special dispensation. Please comply with the
above will appear.
usual safety instructions on how to warn other
Pressing the central locking button unlocks
drivers.
the vehicle.
Above 10 km/h (6 mph), this unlocking is
temporary.
47
General
would block the desired movement, inside or
Doors and door clearances
outside the vehicle.
recommendations for the
If this advice is not followed, injuries or
damage may occur if a person or an object is
sliding side doors
trapped or caught.
WARNING
2
WARNING
Doors must only be operated when the
vehicle is stationary.
Take care not to block the guide space on the
For your safety and that of your passengers,
floor, to allow the door to slide correctly.
as well as for correct operation of the doors,
For safety and functional reasons, do not
you are strongly advised not to drive with a
drive with the sliding side door open.
When open, a door projects beyond the body.
door open.
Allow adequate clearance when parking
Always check that it is safe to operate the
alongside walls, lamp-posts, high pavements,
door and in particular, be sure not to leave
etc.
children or animals near the door controls
without supervision.
An audible warning, "door open” warning
lamp and onscreen message are there to
NOTICE
remind you. Contact a TOYOTA dealer or a
qualified workshop if you want to deactivate
To hold the sliding side door in the open
this warning.
position, open the door fully to engage the
Lock the vehicle when you use an automatic
latch (located at the bottom of the door).
car wash.
NOTICE
NOTICE
WARNING
When open, a door never projects beyond the
To hold the sliding side door in the open
Before opening or closing and while moving
rear bumper.
position, open the door fully to engage the
doors, ensure that no person, animal or object
latch (located at the bottom of the door).
is in the door frame or any other position that
48
On a steep slope
Rear roof flap
- Lower the rear roof flap.
- While pressing on the rear roof flap
(downwards), take the two spring rings and then
place the hook in its housing.
This roof flap at the rear is compatible only with
- Lower the black paddle to lock the rear roof
side-hinged doors.
flap.
Locking the rear roof flap holds it firmly against
the seal, ensuring watertight sealing with no
Take care when opening doors while the vehicle
noise.
is on a slope facing uphill. The sloping terrain
could cause the door to open more quickly than
Support bar
usual.
The vehicle is equipped with a support bar for
On a steep slope, manually guide the side door
transporting long loads, after opening the rear
to help it to close.
roof flap.
If the vehicle is on a slope facing downhill,
► Fold back the support bar by lifting the lever.
the door may not stay open, instead closing
To open the rear roof flap:
► Guide it to the door pillar.
suddenly, with a risk of injury. Always hold
- Lift the black paddle of the toggle.
► Support the long loads to be transported, lift
the door to ensure that it does not close
- Relax the toggle by pressing on the rear roof
them and reposition the support bar with one
unexpectedly.
flap (downwards) then release the hook.
hand.
- Lift the rear roof flap.
► Ensure that it is secured correctly by
WARNING
- Move past the point of resistance to lock the
pressing the handle downwards past the point of
rear roof flap with the support props.
On a steep slope, the door's weight may
resistance and lash the load securely.
cause it to move, opening or closing
The side supports can be used as hooking
WARNING
suddenly as a result.
points.
Avoid leaving the vehicle unsupervised on a
Never drive without the props in place.
steep slope with one or more doors open. If
this advice is not followed, injuries or damage
To close the rear roof flap:
may occur if a person or an object is trapped
- Check that the support bar is properly
or caught.
secured.
49
Alarm
Volumetric
NOTICE
(without partition)
The rear bumper has been reinforced to serve
as a step when entering the vehicle.
WARNING
2
Never fasten a load to the roof flap.
The system checks for any variation in volume in
the passenger compartment.
System which protects and provides a deterrent
The alarm is triggered if anyone breaks a
WARNING
against theft and break-ins.
window, enters the passenger compartment or
moves inside the vehicle.
Never drive without the support bar in place.
WARNING
The rear doors will only lock when the support
bar is installed.
Self-protection function
(with partition)
When the roof flap is open, take care when
The system checks for the disconnection of
driving where height is restricted.
any of its components.
The system only checks for a variation in volume
Never rest loads directly on the rear doors.
The alarm is triggered if the battery, button or
inside the cab.
Comply with the usual indications for warning
siren wiring is disconnected or damaged.
The alarm is triggered if anyone breaks a
other drivers.
For all work on the alarm system, contact a
window or enters the vehicle’s cab.
Only use the roof flap on short trips.
TOYOTA dealer or a qualified workshop.
It will not be triggered if someone enters the
loading area.
Exterior perimeter
NOTICE
The system checks whether the vehicle is
opened.
If your vehicle is fitted with Additional Heating
The alarm is triggered if anyone tries to open
/ Ventilation, volumetric monitoring is not
one of the doors or the bonnet.
compatible with this system.
For more information on Additional Heating
/ Ventilation, refer to the corresponding
section.
50
Anti-tilt monitoring
Locking the vehicle
NOTICE
The system checks for any change in the attitude
with exterior perimeter
of the vehicle.
If an opening (door, boot or bonnet) is not
monitoring only
The alarm is triggered if the vehicle is lifted or
closed properly, the vehicle is not locked but
moved.
the exterior perimeter monitoring will be
Disable volumetric and anti-tilt monitoring to
activated after 45 seconds at the same time
avoid unwanted alarm triggering in certain cases,
NOTICE
as the interior volumetric and anti-tilt
such as:
monitoring.
- Slightly open window or sunroof.
When the vehicle is parked, the alarm will not
- Washing the vehicle.
be triggered if the vehicle is knocked.
- Changing a wheel.
Deactivation
- Towing your vehicle.
► Press the unlocking button on the remote
- Transport on a ship or ferry.
Locking the vehicle with full
control.
alarm system
or
Deactivating the interior volumetric
► Unlock the vehicle with the Keyless Entry and
and anti-tilt monitoring
Activation
Starting system.
► Switch off the ignition and within 10 seconds
The monitoring system is deactivated: the
► Switch off the engine and exit the vehicle.
press the alarm button until its red indicator lamp
indicator lamp in the button goes off and the
► Lock the vehicle using the remote control or
is on fixed.
direction indicators flash for about 2 seconds.
the "Keyless Entry and Starting" system.
► Get out of the vehicle.
The monitoring system is active: the red indicator
► Immediately lock the vehicle using the remote
NOTICE
lamp in the button flashes every second and
control or the "Keyless Entry and Starting"
the direction indicators come on for about 2
system.
When the vehicle automatically locks itself
seconds.
Only the exterior perimeter monitoring is
again (as happens if a door or the boot is not
activated; the red indicator lamp in the button
opened within 30 seconds of unlocking), the
NOTICE
flashes every second.
monitoring system is also reactivated
automatically.
Following an instruction to lock the vehicle,
NOTICE
the exterior perimeter monitoring is activated
after 5 seconds and the interior volumetric
To be taken into account, the deactivation
and anti-tilt monitoring after 45 seconds.
must be carried out every time the ignition is
switched off.
51
Reactivating the interior volumetric
Failure of the remote control
Malfunction
and anti-tilt monitoring
To deactivate the monitoring functions:
When the ignition is switched on, the fixed
► Deactivate the perimeter monitoring by
► Unlock the vehicle using the key in the front
lighting of the red indicator lamp in the button
unlocking the vehicle with the remote control or
left-handed door lock.
indicates a system malfunction.
the Keyless Entry and Starting system.
► Open the door; the alarm is triggered.
Have it checked by any authorized Toyota
The indicator lamp in the button goes off.
► Switch on the ignition; the alarm stops; the
retailer or Toyota authorized repairer, or any
2
► Reactivate all monitoring by locking the
indicator lamp in the button goes off.
reliable repairer.
vehicle with the remote control or the Keyless
Entry and Starting system.
Locking the vehicle without
Automatic activation
The red indicator lamp in the button once again
(Depending on version)
activating the alarm
flashes every second.
The system is activated automatically 2 minutes
► Lock or deadlock the vehicle using the key
after the last door or the boot is closed.
(integral to the remote control) in the driver's
Triggering of the alarm
► To avoid triggering the alarm on entering the
door lock.
This is indicated by sounding of the siren
vehicle, first press the unlocking button on the
and flashing of the direction indicators for 30
remote control or unlock the vehicle using the
seconds.
“Keyless Entry and Starting” system.
Depending on the country of sale, certain
monitoring functions remain active until the alarm
has been triggered eleven times consecutively.
When the vehicle is unlocked using the remote
control or the "Keyless Entry and Starting"
system, rapid flashing of the red indicator lamp
in the button informs you that the alarm was
triggered during your absence. When the ignition
is switched on, the flashing stops immediately.
52
Anti-pinch
Electric windows
2. Right-hand front
3. Right-hand rear (depending on version)
(Depending on version)
4. Left-hand rear (depending on version)
If the window meets an obstacle while rising, it
Type 1
5. Deactivation of the electric window controls
stops and immediately partially lowers again.
located by the rear seats (depending on
version)
Deactivating the rear
controls for the rear electric
Manual operation
windows
► To open/close the window, press/pull the
(Type 2)
1. Left-hand front
switch without passing the point of resistance;
2. Right-hand front
the window stops as soon as the switch is
released.
Type 2
Automatic operation
(Depending on version)
For your children's safety, press control 5 to
► To open/close the window, press/pull the
deactivate the controls for the rear electric
switch past its resistance point: the window
windows, irrespective of their positions.
opens/closes completely when the switch is
The red indicator lamp in the button comes
released.
on and a confirmation message is displayed.
Operating the switch again stops the movement
The lamp will remain lit until the controls are
of the window.
reactivated.
The rear electric windows can still be controlled
NOTICE
using the driver's controls.
Window controls remain operational for
Reinitialising the electric
approximately 45 seconds after switching off
the ignition or after locking the vehicle.
windows
After that time, the controls are disabled.
After reconnecting the battery, or in the event
To reactivate them, switch on the ignition or
of abnormal window movement, the anti-pinch
unlock the vehicle.
function must be reinitialised.
The anti-pinch function is disabled during the
following sequence of operations.
1.
Left-hand front
For each window:
53
► Lower the window fully, then raise it; it will
Tilting rear door windows
rise in steps of a few centimetres each time the
control is pressed. Repeat the operation until the
Opening
window is fully closed.
► Continue to pull the control for at least one
second after the window reaches the closed
position.
2
WARNING
If an electric window meets an obstacle
during operation, the movement of the
window must be reversed. To do this, press
the relevant switch.
When the driver operates the passengers’
electric window switches, it is important to
► Turn the lever outwards.
ensure that nothing can prevent the window
► Push it fully to secure the window in the open
from closing properly.
position.
It is important to ensure that passengers use
the electric windows correctly.
Closing
Pay particular attention to children when
► Pull the lever to release the window.
operating windows.
► Turn the lever fully inwards to secure the
Be aware of passengers and/or other persons
window in the closed position.
present when closing windows using the
electronic key.
Do not put your head or arms through the
open windows when the vehicle is moving -
risk of serious injury!
54
dangerous projectiles in the event of sudden
General
WARNING
braking or a collision.
recommendations for the
- Do not remove a head restraint without
Please note: an incorrectly latched backrest
stowing it; secure it to a support inside the
seats
compromises the safety of passengers in the
vehicle.
event of sudden braking or an impact.
- Check that the seat belts remain accessible
The contents of the boot may be thrown
WARNING
to the passenger and easy to fasten.
forward - risk of severe injury!
- Passengers must never take their seat
For safety reasons, seat adjustments must
without adjusting and fastening their seat belt.
only be made when the vehicle is stationary.
- In row 3, be careful not to leave your feet
Front seats
under the row 2 seat while it is being tilted.
WARNING
- When a row 3 seat is in the fully folded
position, ensure that the strap is correctly
Correct driving position
Folding or unfolding the seat backrests must
hooked to the Top Tether fixing of the row 2
Before taking to the road and to make the most
only be done with the vehicle stationary.
backrest: risk of unexpected tipping of the
of the ergonomic layout of the instruments and
seat.
controls, carry out these adjustments in the
following order:
WARNING
- head restraint height.
WARNING
- seat backrest angle.
Before moving the seat backwards, ensure
- seat cushion height.
that there is no person or object that might
Before carrying out the manoeuvres, check
- longitudinal seat position.
prevent the full travel of the seat.
that nothing and no one is obstructing the
- steering wheel height and reach.
There is a risk of trapping or pinching
moving elements and their locking.
- rear view mirror and door mirrors.
passengers if present in the rear seats or of
To avoid sudden folding, take care to hold the
jamming the seat if large objects are placed
backrest and support it until it is horizontal.
on the floor behind the seat.
Never put your hand underneath the seat
cushion to guide the seat downwards or
upwards, you could get your fingers trapped.
WARNING
Place your hand on the grip/strap (depending
on equipment) at the top of the seat cushion.
Do not place hard or heavy objects on the
backrests forming a table. They could become
55
► Raise the control and slide the seat forwards
Lumbar
or backwards.
(driver only)
Height
(driver only)
3
► Turn the knob manually to obtain the desired
level of lumbar support.
WARNING
► If the vehicle is so equipped, pull the control
Armrest
upwards to raise or push it downwards to lower,
Once these adjustments have been made,
as many times as necessary to obtain the
check that the instrument panel can be
position required.
viewed correctly from your driving position.
NOTICE
Adjustments
For more information on the Seat belts, refer
to the corresponding section.
Longitudinal
Tilting the backrest
► To put the armrest in the vertical position,
► Push the control backwards then use your
raise it until it locks into place.
weight and your legs to adjust the backrest.
► Lower the armrest to return it to the position
for use.
56
The armrest can be removed from the passenger
► While holding it in this position, rotate the
Retractable position
seat.
armrest towards the front. The armrest is once
Removing the armrest
again secured onto the backrest.
► Raise the armrest into the vertical position.
Storage compartment under
the seat
► Push the armrest shaft towards the backrest.
► While holding it in this position, rotate the
armrest towards the rear.
► Pull the armrest to detach it from the
backrest.
► If the centre console inconveniences you,
Refitting the armrest
remove the passenger's seat armrest.
► Push the control rearwards fully to tilt and
► Lift the passenger’s seat cushion to access
guide the assembly.
the storage compartment.
This position allows you to transport long loads
inside the vehicle with the doors closed.
When retracted, the maximum permitted weight
on the backrest is 50 kg (110 lb).
► To reposition the seat cushion, raise the
backrest until it locks in the raised position.
► Slot the armrest into the backrest, ensuring
that you align the bayonet lugs with the holes.
► Push the armrest shaft towards the backrest.
57
Heated seat control
Steering wheel
ECO
adjustment
Do not use the function when the seat is not
occupied.
Reduce the heating intensity as soon as
possible.
3
When the seat and passenger compartment
have reached a satisfactory temperature,
switch the function off; reducing electrical
consumption in turn decreases energy
consumption.
WARNING
► When stationary, pull the control lever to
► Approximately 30 seconds after starting the
Prolonged use of the heated seats is not
release the steering wheel.
engine, press the control.
recommended for those with sensitive skin.
► Adjust the height and reach.
It can be activated when the outside temperature
There is a risk of burns for people whose
► Lower the control lever to lock the steering
is below 20°C.
perception of heat is impaired (illness, taking
wheel.
The temperature is controlled automatically.
medication, etc.).
Pressing again interrupts operation.
To keep the heated pad intact and to prevent
WARNING
a short circuit:
NOTICE
- do not place sharp or heavy objects on the
As a safety precaution, these operations must
seat,
only be carried out while the vehicle is
If you press the control while the engine is not
- do not kneel or stand on the seat,
stationary.
running, the request will be memorised for
- do not spill liquids onto the seat,
approximately 2 minutes.
- never use the heating function if the seat
is wet.
With the two-seat front bench seat, the driver's
seat control switches the heating on or off for the
bench seat’s outer seat.
58
Electric unfolding
Mirrors
WARNING
The door mirrors are unfolded electrically
As a safety measure, the mirrors should be
when the vehicle is unlocked using the remote
Door mirrors
adjusted to reduce the blind spots.
control or key. Unless folding was selected with
The objects observed are, in reality, closer
control A, pull the control in the central position
Adjustment
than they appear.
towards the rear again.
Take this into account when assessing the
distance of vehicles approaching from behind.
NOTICE
Folding/unfolding when locking/unlocking the
Manual folding
vehicle can be deactivated. Contact any
You can manually fold the mirrors (parking
authorized Toyota retailer or Toyota
obstruction, narrow garage, etc.)
authorized repairer, or any reliable repairer.
► Turn the mirror towards the vehicle.
If necessary, the mirrors can be folded
manually.
Electric folding
Depending on equipment, the mirrors can be
Heated mirrors
► Move control A or turn control C (depending
folded electrically.
on the version you have) to the right or to the left
► From the inside, with the
to select the corresponding mirror.
ignition on, place control A in the
► Move control B or C (depending on the
central position.
version you have) in any of the four directions to
► Pull control A backwards.
adjust.
► Return control A or C (depending on the
► Lock the vehicle from the outside.
version you have) to its centre position.
NOTICE
► Press one of these buttons.
If the mirrors are folded using control A, they
will not unfold when the vehicle is unlocked.
NOTICE
For more information on Rear screen
demisting/defrosting, refer to the
corresponding section.
59
Interior rear view mirror
2-seat front bench seat
NOTICE
Equipped with an anti-dazzle system, which
darkens the mirror glass and reduces the
To ensure optimum visibility while
nuisance to the driver caused by the sun,
manoeuvring, the mirror brightens
headlamps of other vehicles, etc.
automatically when reverse gear is engaged.
The system is deactivated if the load in the
Central seat
3
Manual model
boot exceeds the heigh of the load space
Day/night position
cover or if the load space cover has items
Table position
placed on it.
Child-monitoring mirror
► Pull the lever to change to the anti-dazzle
"night” position.
► Push the lever to change to the normal "day"
position.
► To lower the backrest, pull the tab on the
Adjustment
lower edge of the seat.
► Set the mirror to the normal “day” position.
Automatic "electrochrome" model
A child-monitoring mirror is installed above
The electrochrome system uses a sensor that
the interior rear view mirror. It allows the
detects the level of exterior brightness and that
vehicle's rear passengers to be observed and
coming from the rear of the vehicle, in order to
facilitates discussion between the front and rear
automatically and gradually switch between day
passengers without changing the mirror setting
and night usage.
and without turning around. It can be folded
easily to avoid dazzle.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст