Toyota Proace EV (2022 year). Manual in english — page 3

► With the door unlocked, press and

NOTICE

Electric sliding side

hold this button until the corresponding

door(s)

sliding side door has opened.

To deactivate this automatic locking, go to any

authorized Toyota retailer or Toyota

The exterior and interior door handles and the

► Press this button again to reverse the

authorized repairer, or any reliable repairer.

interior buttons allow the electrically powered

direction of the door's movement.

movement of the door to be started.

NOTICE

Opening and closing of the doors is

Manual

accompanied by an audible signal.

The remote control buttons are not active with

► With complete unlocking activated,

the ignition switched on.

press this button to lock (indicator lamp

Opening

comes on)/unlock (indicator lamp goes off) the

With the exterior or interior handle

With the button(s) on the door pillar

vehicle.

► With selective unlocking activated, press this

button to lock (indicator lamp comes on)/unlock

(indicator lamp goes off) the loading area.

WARNING

Driving with the doors locked could make it

► With the door unlocked, pull and release the

more difficult for the emergency services to

handle to start opening the door. Pull the handle

enter the vehicle in an emergency.

again to reverse the direction of the door's

movement.

NOTICE

With the remote control

With the button(s) at the front

The indicator lamp goes off when unlocking

one or more doors of the loading area.

With the ignition off and the vehicle fully

locked, the indicator lamp goes off for energy

economy reasons.

► With total unlocking activated and the child

handle again to reverse the direction of the

NOTICE

lock deactivated, to unlock the vehicle and start

door's movement.

opening a door, press the button corresponding

The button is not operational and pressing it

to the door you wish to open.

NOTICE

results in an audible signal, if the speed of the

► With selective unlocking activated, to unlock

vehicle is above 20 mph (30 km/h).

The remote control buttons are not active with

only the loading area and start opening a door,

the ignition switched on.

press the button corresponding to the door you

wish to open.

NOTICE

With the button(s) on the door pillar

► In both cases, pressing the button again

reverses the direction of the door's movement.

The button(s) at the front or on the door pillar

is not operational and pressing it results in an

Closing

audible signal, if:

- the vehicle is moving,

With the exterior handle

- the child lock is on (activated) (for the

buttons on the door pillars),

- the vehicle has been locked or deadlocked

from outside (using the key, remote control

or Smart Entry & Start, depending on

equipment).

The button for the left-hand door is not

operational and pressing it results in an

With the button(s) at the front

audible signal if the fuel filler flap is open.

► Pull and release the handle to start closing

the door. Pull the handle again to reverse the

direction of the door's movement.

With the remote control

► Press and hold this button until the

► To start closing a door, press the

sliding side door has closed. Pull the

corresponding button for that door. Press again

to reverse the direction of the door's movement.

would block the desired movement, inside or

General

NOTICE

outside the vehicle.

recommendations for the

If this advice is not followed, injuries or

The electric controls are disabled in the event

damage may occur if any part of a person or

sliding side doors

of an impact. Manual opening and closing

an object is trapped or caught.

remain possible.

Electrical door opening is disabled at speeds

WARNING

above 2 mph (3 km/h):

- However, if the vehicle started moving

NOTICE

Doors must only be operated when the

while the doors were open, the speed must

vehicle is stationary.

While starting the engine, door movements

be reduced below 19 mph (30 km/h) before

For your safety and that of your passengers,

are paused, resuming when the engine is

they can be closed.

as well as for correct operation of the doors,

running.

- Any attempt to open a door electrically

you are strongly advised not to drive with a

using the interior handle while driving results

door open.

in it only being possible to open the door

Always check that it is safe to operate the

NOTICE

manually.

door and in particular, be sure not to leave

- This situation is accompanied by the

Depending on the engine fitted, if the

children or animals near the door controls

audible warning, the lighting of the "door

door is closed and an opening request

without supervision.

open" warning lamp and the message on the

is issued in Stop mode of Stop & Start, the

The audible warning, the lighting of the "door

screen. To release the door and be able to

door will open slightly and then stop. In Start

open" warning lamp and the message on

operate it again, it is necessary to stop the

mode, the door will resume its movement

the screen are there to remind you. Contact

vehicle.

when the engine re-starts.

any authorized Toyota retailer or Toyota

authorized repairer, or any reliable repairer if

you want to deactivate this warning.

WARNING

NOTICE

Lock the vehicle when you use an automatic

car wash.

Take care not to block the guide space on the

To hold the sliding side door in the open

floor so that the door can slide correctly.

position, open the door fully to engage the

For safety and functional reasons, do not

latch (located at the bottom of the door).

WARNING

drive with the sliding side door open.

Before opening or closing and while moving

doors, ensure that no person, animal or object

is in the door frame or any other position that

Doors and door clearances

Safety/Obstacle detection

Reinitialising electric doors

with electric door(s)

If electrical operations no longer work:

► Fully close the door(s) manually.

► Fully open the door(s) electrically.

► Close the door(s) electrically.

On completion of this procedure, electric

operation of the doors is restored.

However, if a problem persists following this

procedure, contact any authorized Toyota retailer

or Toyota authorized repairer, or any reliable

When open, a door projects beyond the body.

repairer.

Allow adequate clearance when parking

The obstacle detection system is triggered when

alongside walls, lamp-posts, high pavements,

On a steep slope

the moving door encounters an obstacle with a

etc.

certain level of physical resistance. If an obstacle

is detected:

- while the door is closing, the door stops then

opens fully.

- while the door is opening, the door stops then

closes.

- twice in succession during a movement of the

door, the door will no longer close electrically

It is possible to open and close the doors

(uninitialisation).

electrically on slopes of up to a 20% gradient.

On a steep slope: a safety system slows down

If the vehicle is on a slope, with the front of the

the movement of the door.

vehicle facing up the slope, open the door with

NOTICE

In all cases, wait a few seconds before operating

care. The door may open more quickly due to

the door (closing or opening).

When open, a door never projects beyond the

the incline.

Close the door manually for safety reasons.

rear bumper.

On a steep slope, guide the side door manually

Then reinitialise the door.

to help it to close.

Hands-free sliding side

WARNING

door(s)

Before making the movement with your foot,

ensure that you are steady and well

Opening/Closing

positioned, so that you do not lose your

balance (rain, snow, ice, mud, etc.).

Take care not to touch the exhaust tailpipe

If your vehicle is on a slope, with the front of the

when making the movement with your foot -

vehicle facing down the slope, the door may not

risk of burns.

stay open and may close violently with the risk

of injury.

WARNING

In the case of a steep slope, the door may be

driven by its own weight and as a

consequence may open or close violently.

There would not be time for action at the

With a movement of your foot while keeping the

electric controls to take effect.

remote control on your person in the recognition

There would not be time for the obstacle

zone A, the system unlocks and opens the

detection system to react.

sliding side door or closes and locks it.

Take care not to leave the vehicle on a

The remote control must be located at the rear

► Put your foot beneath the corner of the rear

steep slope with the door(s) open without

of the vehicle, at least about 30 cm but no more

bumper, then move the foot at normal speed with

supervision. If this advice is not followed,

than about 2 m from the vehicle.

a sweeping side movement.

injuries or damage may occur if a person or

an object is trapped or caught.

NOTICE

The sensor detects the foot approaching and

leaving and triggers the opening or closing of the

The automatic locking after closing the door

side door.

can be programmed in the vehicle

configuration menu.

NOTICE

Make the movement without interruption and

If your vehicle is not fitted with an alarm,

If the "Hands-free tailgate access self-

do not repeat it immediately afterwards or

locking is signalled by the fixed illumination of

locking" option is selected in the vehicle

several times.

the direction indicators for about two seconds.

menu and after closing the door, check that

If the door does not open, wait about

Depending on your version, the door mirrors

the vehicle is properly locked.

2 seconds before trying again.

fold at the same time.

Locking will not take place:

Do not keep the foot in the air.

- if the ignition is on,

- if one of the doors or the tailgate is open,

Activation/Deactivation

- if a "Smart Entry & Start" remote control is

NOTICE

With audio system or touch screen

inside the vehicle.

If a number of gestures with your foot have

Confirmation that the door is going to open or

By default, hands-free access is activated.

no effect, wait a few seconds before starting

close is signalled by the direction indicators

The "Hands-Free Tailgate Access"

again.

flashing for a few seconds, accompanied by

function or automatic vehicle

The system is automatically deactivated in

an audible signal.

locking when the sliding door is closed is

heavy rain or with accumulations of snow.

The movement of the door is reversed if the

activated and deactivated via the vehicle

If it does not work, make sure that the

movement of the foot takes place during the

configuration menu.

remote control is not exposed to a source of

manoeuvre.

Malfunction

electromagnetic interference (smartphone,

If the vehicle is so equipped, the electric door

etc.).

mirrors fold/unfold on locking/unlocking the

An audible signal repeated three times while

Operation may be affected if using a

vehicle.

using the function indicates a fault with the

prosthetic leg.

system.

This system may not work correctly if your

Contact any authorized Toyota retailer or Toyota

Automatic locking

vehicle is fitted with a towbar.

authorized repairer, or any reliable repairer to

The vehicle locks itself following the hands-free

have the system checked.

closing of the sliding door.

NOTICE

The side door may open or close without

warning if:

- Your vehicle is fitted with a towbar.

- A trailer is coupled or decoupled.

- A bicycle carrier is installed or removed.

- Bicycles are loaded on to or unloaded from

If the left-hand side-hinged door is not properly

Side-hinged rear doors

the bicycle carrier.

closed, the "door open" warning lamp lights up

- Something is deposited or lifted behind the

(the right-hand door is not detected). For more

vehicle.

information on the List of warning lamps and,

- An animal approaches the bumper,

in particular, the door open warning, refer to the

- The vehicle is washed.

corresponding section.

- The vehicle is being serviced.

- A wheel is changed.

Opening to

To avoid any sudden operation, keep the key

approximately 180°

away from the detection zone (also from the

boot’s interior sides) or deactivate the function

in the vehicle configuration menu.

► After first opening the left-hand door, pull the

WARNING

lever A towards you to open the right-hand door.

Ensure that no person or object might prevent

Closing

the correct opening or closing of the doors.

► First close the right-hand door, then the left-

Be aware of children when operating the

hand door.

doors.

NOTICE

If fitted to your vehicle, a check strap system

If the left-hand door is closed first, a buffer

allows the doors to be opened from about 90° to

stop located on the edge of the right-hand

about 180°.

door prevents it closing.

► Pull the yellow control when the door is open.

The check strap will engage again automatically

on closing.

WARNING

Tailgate

Tailgate rear screen

The opening rear screen allows you to access

When parked with the rear doors open to 90°,

Opening

the rear of the vehicle directly, without having to

the doors will cover the rear lamps. In order to

open the tailgate.

warn other road users travelling in the same

direction (who may not be aware that the

Opening

vehicle is stationary) of the vehicle's position,

use a warning triangle or other device

required by legislation and regulations in your

country.

► After unlocking the vehicle, pull the handle,

then raise the tailgate.

Closing

► Lower the tailgate using the interior grab

After unlocking the vehicle, press this control and

handle, then lock it.

lift the rear screen to open it.

If the tailgate is not properly closed, the "door

open" warning lamp comes on. For more

Closing

information on the list of warning and indicator

Close the rear screen by pressing the centre of

lamps, and in particular the door open warning,

the glass until it is fully closed.

refer to the corresponding section.

If the tailgate rear screen is not properly closed,

the "door open" warning lamp comes on. For

WARNING

more information on the list of warning and

indicator lamps and in particular the door open

In the event of a malfunction or if you

warning, refer to the corresponding section.

experience difficulty opening or closing the

tailgate, have it checked by any authorized

NOTICE

Toyota retailer or Toyota authorized repairer,

or any reliable repairer without delay, to avoid

The tailgate and rear screen cannot both be

the issue deteriorating and prevent any risk of

open at the same time, to avoid damaging

the tailgate dropping, potentially causing

them.

serious injury.

Alarm

Locking the vehicle with full

The system checks for any

variation in volume in the

alarm system

passenger compartment.

The alarm is triggered if anyone

Activation

(Depending on version)

breaks a window, enters the

► Switch off the ignition and exit the vehicle.

passenger compartment or

► Lock or deadlock the vehicle using the

moves inside the vehicle.

remote control or with the "Smart Entry & Start"

system.

Self-protection function

When the monitoring system is active, the red

The system checks for the putting out of service

indicator lamp in the button flashes once per

of its components.

second and the direction indicators come on for

The alarm is triggered if the battery, the central

about 2 seconds.

control or the siren wiring is put out of service or

The exterior perimeter monitoring is activated

System which protects and provides a deterrent

damaged.

after 5 seconds and the interior volumetric

against theft and break-ins.

monitoring after 45 seconds.

WARNING

Exterior perimeter monitoring

WARNING

The system checks for opening of the vehicle.

For all work on the alarm system, contact any

The alarm is triggered if anyone tries to open a

authorized Toyota retailer or Toyota

If an opening (door, tailgate/side-hinged doors

door, the boot or the bonnet, for example.

authorized repairer, or any reliable repairer.

or bonnet) is not properly closed, the vehicle

Interior volumetric monitoring

is not locked, but the exterior perimeter

monitoring will be activated after 45 seconds,

The system only checks for any

NOTICE

at the same time as the interior volumetric

variation in volume in the cab.

monitoring.

If your vehicle is fitted with Additional Heating

The alarm is triggered if

/ Ventilation, volumetric monitoring is not

someone breaks a window

compatible with this system.

Deactivation

or enters the vehicle’s cab;

For more information on Additional Heating

however it is not triggered if

► Press the remote control unlocking

/ Ventilation, refer to the corresponding

someone enters the loading

button.

section.

area.

► Unlock the vehicle with the Smart Entry &

Start system.

The monitoring system is deactivated: the

Locking the vehicle

Reactivating interior volumetric

indicator lamp in the button goes off and the

monitoring

with exterior perimeter

direction indicators flash for about 2 seconds.

► Deactivate exterior perimeter monitoring by

monitoring only

unlocking the vehicle using the remote control or

NOTICE

Deactivate the interior volumetric monitoring to

the "Smart Entry & Start" system.

avoid the unwanted triggering of the alarm, in

The indicator lamp in the button goes off.

When the vehicle automatically locks itself

certain cases such as:

► Reactivate the full alarm system by locking

again (as happens if a door or the boot is not

- Slightly open window.

the vehicle using the remote control or the

opened within 30 seconds of unlocking), the

- Washing the vehicle.

"Smart Entry & Start" system.

monitoring system is also reactivated

- Changing a wheel.

The red indicator lamp in the button once again

automatically.

- Towing the vehicle.

flashes every second.

- Transport on a ship or ferry.

Triggering of the alarm

Locking the vehicle without

Deactivating interior volumetric

This is indicated by sounding of the siren

activating the alarm

monitoring

and flashing of the direction indicators for 30

► Lock or deadlock the vehicle using the key

seconds.

► Switch off the ignition and within 10 seconds

(integral to the remote control) in the driver's

The monitoring functions remain active until

press the alarm button until the indicator lamp is

door lock.

the alarm has been triggered ten times in

on fixed.

succession.

► Exit the vehicle.

Failure of the remote control

When the vehicle is unlocked, rapid flashing of

► Immediately lock the vehicle using the remote

To deactivate the monitoring functions:

the indicator lamp in the button indicates that the

control or the "Smart Entry & Start" system.

► unlock the vehicle using the key (integral to

alarm was triggered during your absence. When

Only exterior perimeter monitoring is activated;

the remote control) in the driver's door lock,

the ignition is switched on, this flashing stops

the red indicator lamp in the button flashes every

► open the door; the alarm is triggered,

immediately.

second.

► switch on the ignition; the alarm stops; the

To take effect, this deactivation must be

indicator lamp in the button goes off.

performed whenever the ignition is switched

off.

Malfunction

When the ignition is switched on, the fixed

lighting of the red indicator lamp in the button

indicates a system malfunction.

Have it checked by any authorized Toyota

control is pressed. Repeat the operation until the

NOTICE

retailer or Toyota authorized repairer, or any

window is fully closed.

reliable repairer.

► Continue to pull the control for at least one

The electric window controls remain

second after the window reaches the closed

operational for about 45 seconds after the

Automatic activation

position.

ignition is switched off if the front doors are

(Depending on the country of sale)

not open.

The system is activated automatically 2 minutes

WARNING

After that time, the controls are disabled. To

after the last door or the boot is closed.

reactivate them, switch the ignition on again.

If an electric window meets an obstacle

► To avoid triggering the alarm on entering the

during operation, the movement of the

vehicle, first press the unlocking button on the

Safety anti-pinch

window must be reversed. To do this, press

remote control or unlock the vehicle using the

the relevant switch.

“Smart Entry & Start” system.

If your vehicle is fitted with the safety anti-pinch

When the driver operates the passenger

function, when the window rises and meets an

electric window switch, it is important to

obstacle, it stops and partially lowers.

Electric windows

ensure that nothing can prevent the window

In the event of unwanted opening of the window

from closing properly.

on closing, press the control until the window

Pay particular attention to children when

opens completely. Within 4 seconds, pull the

operating windows.

control until the window closes.

The safety anti-pinch does not operate while

1. Left-hand electric window control.

doing this.

2. Right-hand electric window control.

Reinitialising the electric

Operation

windows

► To open/close the window manually, press/

After reconnecting the battery, or in the event

pull the switch without passing the point of

of abnormal window movement, the anti-pinch

resistance; the window stops as soon as the

function must be reinitialised.

switch is released.

The anti-pinch function is disabled during the

► To open/close the window automatically,

following sequence of operations.

press/pull the switch fully, beyond the point of

For each window:

resistance; the window opens/closes completely

► Lower the window fully, then raise it; it will

when the switch is released (pressing the switch

rise in steps of a few centimetres each time the

again stops the movement of the window).

Correct driving position

Manually-adjusted front

Height

Before taking to the road and to make the most

seats

of the ergonomic layout of the instruments and

controls, carry out these adjustments in the

NOTICE

following order:

- head restraint height.

For more information on the Seat belts, refer

- seat backrest angle.

to the corresponding section.

- seat cushion height.

► Pull the control upwards to raise the seat or

- longitudinal seat position.

push it downwards to lower the seat, until the

- steering wheel height and reach.

Longitudinal

position required is obtained.

- rear view mirror and door mirrors.

Backrest angle

► Raise the control bar and slide the seat

forwards or backwards.

► Release the bar to lock the seat in position on

► Depending on equipment, turn the knob

one of the notches.

or pull the control all the way up and tilt the

backrest forwards or backwards to adjust it.

WARNING

Lumbar

WARNING

Before moving the seat backwards, ensure

that there is nothing that might prevent the full

Once these adjustments have been made,

travel of the seat.

check that the instrument panel can be

There is a risk of trapping or pinching

viewed correctly from your driving position.

passengers if present in the rear seats or

jamming the seat if large objects are placed

on the floor behind the seat.

► Turn the knob manually to obtain the desired

level of lumbar support.

Table position of the driver's

Electric front seat

and/or the front passenger

NOTICE

seat backrest

To avoid discharging the battery, carry out

these adjustments with the engine running.

On the front passenger side, this position allows

NOTICE

long objects to be carried.

On the driver's side, this position allows rear

For more information on the Seat belts, refer

passengers to be helped out of the vehicle (by

► Pull the control fully up and tip the backrest

to the corresponding section.

the emergency services).

forward.

To return to the normal position, pull the control

WARNING

up to release the backrest, then pull the backrest

Longitudinal

up to its raised position.

Check that there is no object that could

interfere with the movement of a seat, both

WARNING

above and below.

When sharp deceleration occurs, objects

► Place the head restraint in the low position,

placed on the folded backrest can turn into

and if fitted to your vehicle, raise the armrest and

projectiles.

fold the table fitted to the back of the seat.

► Push the control forwards or rearwards to

slide the seat.

NOTICE

WARNING

We recommend deactivating the front

passenger airbag.

Before moving the seat backwards, ensure

that there is nothing that might prevent the full

travel of the seat.

There is a risk of trapping or pinching

passengers if present in the rear seats or

jamming the seat if large objects are placed

on the floor behind the seat.

Seat cushion height

Head restraint height

WARNING

adjustment

The head restraint has a frame with notches

which prevents it from lowering; this is a

safety device in case of impact.

The adjustment is correct when the upper

edge of the head restraint is level with the

top of the head.

► Tilt the control upwards or downwards to

Never drive with the head restraints removed;

obtain the desired height.

they must be fitted and correctly adjusted.

Backrest angle

If fitted to your vehicle.

► To raise it, pull it upwards as far as possible

(notch).

► Tilt the control forwards or rearwards to

► To remove it, press the lug A and pull it

adjust the angle of the backrest.

upwards.

► To put it back in place, engage the head

restraint rods in the openings keeping them in

line with the seat backrest.

► To lower it, press the lug A and push down on

the head restraint at the same time.

2-seat front bench seat

Armrest

Heated seats and bench

If fitted in the vehicle, this is fixed and has a seat

seat

belt built into the backrest for the seat next to the

driver’s seat.

NOTICE

For more information on the Seat belts, refer

to the corresponding section.

Under-seat storage

The armrest has notches.

► Pull the armrest fully up

► Lower it fully down.

► Raise the armrest to the desired position.

If the vehicle is so equipped, a storage space is

provided under the seat.

► Pull the strap towards you to tip the seat

cushion.

If fitted to your vehicle.

► With the engine running and when the

outside temperature is below 20°C, use the

adjustment knob to switch on and select the level

of heating required from 0 (off) to 3 (high).

This function provides lumbar massage; it only

WARNING

Electric lumbar

operates when the engine is running as well as

adjustment

in STOP mode of the Stop & Start system.

Prolonged use of heated seats is not

recommended for those with sensitive skin.

Activation/Deactivation

There is a risk of burns for people whose

perception of heat is impaired (illness, taking

► Press this button to activate/deactivate

medication, etc.).

the function.

To keep the heated pad intact and to prevent

Upon activation, the indicator lamp comes on.

a short circuit:

The massage function is activated for a period

- Do not place heavy or sharp objects on the

of one hour.

seat.

During this time, massage is performed in

- Do not kneel or stand on the seat.

6 cycles of 10 minutes (6 minutes of massage

- Do not spill liquids onto the seat.

followed by a 4-minute break).

- Never use the heating function if the seat

After one hour, the function is deactivated; the

is wet.

indicator lamp goes off.

► Press the control to obtain the desired lumbar

support.

Adjustment of intensity

ECO

Massage function

Do not use the function when the seat is not

occupied.

Reduce the heating intensity as soon as

possible.

When the seat and passenger compartment

have reached a satisfactory temperature,

switch the function off; reducing electricity

consumption in turn decreases fuel

consumption.

Press this button to adjust the intensity of

the massage.

Two levels of massage are available.

Manual folding

Steering wheel

Mirrors

The mirrors can be folded manually (parking

adjustment

obstruction, narrow garage, etc.).

Door mirrors

► Turn the mirror towards the vehicle.

WARNING

Electric folding

Depending on equipment, the mirrors can be

As a safety measure, the mirrors should be

folded electrically, when the vehicle is parked.

adjusted to reduce the "blind spots".

The objects that you see in the mirrors are

► From the inside, with the

in fact closer than they appear. Take this

ignition on, place control A in the

into account in order to correctly judge the

central position.

distance of vehicles approaching from behind.

► Pull control A backwards.

► Lock the vehicle from the outside.

► When stationary, lower the control lever to

Electric unfolding

release the steering wheel.

The door mirrors are unfolded electrically

► Adjust the height and reach.

when the vehicle is unlocked using the remote

► Pull the control lever to lock the steering

control or key. Unless folding was selected with

wheel.

control A, pull the control in the central position

towards the rear again.

WARNING

As a safety precaution, these operations must

NOTICE

only be carried out while the vehicle is

Folding/unfolding when locking/unlocking the

stationary.

► Move control A to the right or to the left to

vehicle can be deactivated. Contact any

select the corresponding mirror.

authorized Toyota retailer or Toyota

► Move control B in any of the four directions

authorized repairer, or any reliable repairer.

to adjust.

If necessary, the mirrors can be folded

► Return control A to its central position.

manually.

Heated mirrors

Manual model

Windscreen zone for toll

Day/night position

badge

Depending on the version, the vehicle can be

equiped with a athermic windscreen type.

For a best functionnement of the toll badge

system, it is necessary to place the toll badge on

the windscreen zone provided for the purpose

symbolised with of black dotteds around of the

► Press this button.

► Pull the lever to change to the anti-dazzle

interior rear view mirror base.

"night” position.

NOTICE

► Push the lever to change to the normal "day"

position.

For more information on Rear screen

Adjustment

demisting/defrosting, refer to the

► Set the mirror to the normal “day” position.

corresponding section.

Automatic "electrochrome" model

This system automatically and gradually

Interior rear view mirror

transitions between day and night use, with the

Equipped with an anti-dazzle system, which

aid of a sensor that measures the light arriving

darkens the mirror glass and reduces the

from the rear of the vehicle.

nuisance to the driver caused by the sun,

NOTICE

headlamps of other vehicles, etc.

NOTICE

For the version without athermic windscreen,

To ensure optimum visibility while

to limit the obstruction of you field of vision

manoeuvring, the mirror lightens automatically

through the windscreen, we recommend you

when reverse gear is engaged.

to place the toll badge in the upper part of the

windscreen.

Smart Cargo

Removable flap (type 1)

Refitting the flap

Removing the flap

The cushion of the bench seat's outer seat can

be folded up against the backrest to create a

loading area inside the cab.

A removable flap on the partition can be

removed to allow long objects to be loaded.

► Tilt the flap, with the yellow hinges pointing

downwards.

► Insert the hinges into their housing then press

down fully (to avoid vibrations).

► With one hand lift the flap to close it, then

► While holding the flap with one hand, turn the

with the other hand turn the control at the top of

control at the top of the flap with the other hand

the flap to secure it.

to release it.

NOTICE

► Lower the flap to remove it from its housing.

Removable flap (type 2)

► Stow it behind the driver’s seat, clipping it into

Once the removable flap has been removed,

the attachment lugs.

you can load long objects under the outer

► Turn the control at the top of the flap to

seat.

secure it.

► To open or close the flap, slide it to the left

or right.

The flap is kept in the closed or open position

WARNING

with magnets located at each end position.

Never put your hand underneath the seat

When the outer seat is raised and the flap is

Folding seat cushion

cushion to guide it upwards, as your fingers

removed, you must install the anti-slip net.

Raising the seat cushion

may become trapped.

Refer to the Anti-slip net section.

Always use only the strap.

► With one hand, firmly pull the strap forwards

to unlock the seat cushion.

► A strut lifts the seat cushoin against the

backrest.

Lowering the seat cushion

Anti-slip net

turn it a quarter turn (in a clockwise direction) to

lock it.

Installing the net

► Put the second fastener into the lower

cut-out 2, located on the seat base. Keep the

fastener pressed against the structure, then turn

it a quarter turn (in a clockwise direction) to lock

it.

► Secure the first hook to the ring 3 located in

the glove box.

► Secure the second hook to the ring 4 located

on the floor.

Removing the net

► Release the hooks from the rings 4 and 3.

► Remove the anti-slip net.

► Remove the lower fastener 2 then the upper

► To reposition the seat cushion, press firmly

fastener 1, turning them by a quarter turn

on the top of the seat with one hand to lower the

backwards to unlock them.

seat cushion until it locks into the seat position.

WARNING

Ensure that there are no objects or feet

obstructing the anchorage points or

preventing the assembly from locking

► Put the first fastener into the upper cut-out 1,

properly.

located beneath the folded seat cushion. Keep

the fastener pressed against the structure, then

Была ли эта страница вам полезна?

Да!Нет

Toyota Proace EV (2022 year). Manual in english — page 3

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.