Toyota Sequoia (2018 year). Instruction — part 24
369
5
In
SEQUOIA_OM_USA_OM0C011U
The status of the opening and
closing of a garage door is shown
by the indicators.
Opening
Closing
This function is only available if the
garage door opener motor used is
a compatible device. (To check
device compatibility, refer to
www.HomeLink.com.)
The indicators can operate within approximately 820 ft. (250 m) of
the garage door. However, if there are obstructions between the
garage door and the vehicle, such as houses and trees, feedback
signals from the garage door may not be received. To recall the pre-
vious door operation status, press and release either HomeLink
®
buttons
and
or
and
simultaneously.
The
last recorded status will be displayed for 3 seconds.
Garage door operation indicators
Color
Status
Orange (flashing)
Currently opening/closing
Green
Opening/closing has completed
Red (flashing)
Feedback signals cannot be received
370
SEQUOIA_OM_USA_OM0C011U
Press and hold the 2 outside but-
tons for 10 seconds until the
HomeLink
®
indicator light
changes from continuously lit
orange to rapidly flashing green.
If you sell your vehicle, be sure to
erase the programs stored in the
HomeLink
®
memory.
■
Codes stored in the HomeLink
®
memory
●
The registered codes are not erased even if the battery cable is discon-
nected.
●
If learning failed when registering a different code to a HomeLink
®
button
that already has a code registered to it, the already registered code will not
be erased.
■
Before programming
●
Install a new battery in the transmitter.
●
The battery side of the transmitter must be pointed away from the
HomeLink
®
.
Erasing the entire HomeLink
®
memory (all three codes)
371
5
In
SEQUOIA_OM_USA_OM0C011U
■
Certification for the garage door opener
For vehicles sold in the U.S.A.
FCC ID: NZLAECHL5
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
For vehicles sold in Canada
NOTE:
This device complies with Industry Canada licence-exempt RSS stan-
dard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interfer-
ence, including interference that may cause undesired operation of the
device.
REMARQUE:
Le present appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisee aux
deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique
subi, meme si le brouillage est susceptible d’en compromettre le
fonctionnement.
■
When support is necessary
Visit on the web at www.homelink.com/toyota or call 1-800-355-3515.
WARNING
■
When programming a garage door or other remote control device
The garage door or other device may operate, so ensure people and
objects are out of danger to prevent potential harm.
■
Conforming to federal safety standards
Do not use the HomeLink
®
compatible transceiver with any garage door
opener or device that lacks safety stop and reverse features as required by
federal safety standards. This includes any garage door that cannot detect
an interfering object. A door or device without these features increases the
risk of death or serious injury.
■
When operating or programming HomeLink
®
Never allow a child to operate or play with the HomeLink
®
buttons.
372
SEQUOIA_OM_USA_OM0C011U
Compass
∗
To turn the compass on or off, press the button for more than 3 sec-
onds.
∗
: If equipped
The compass on the inside rear view mirror indicates the direc-
tion in which the vehicle is heading.
Operation
Type A
Type B
Displays and directions
Display
Direction
N
North
NE
Northeast
E
East
SE
Southeast
S
South
SW
Southwest
W
West
NW
Northwest
373
5
In
SEQUOIA_OM_USA_OM0C011U
The direction display deviates from the true direction determined by
the earth’s magnetic field. The amount of deviation varies according to
the geographic position of the vehicle.
If you cross over a map boundary shown in illustration, the compass will
deviate.
To obtain higher precision or accurate calibration, refer to the following.
■
Deviation calibration
Stop the vehicle where it is safe to drive in a circle.
Press the hold the button for 6 seconds. A number (1 to 15)
appears on the compass display.
Press the switch, and referring to the map above, select the num-
ber of the zone where you are.
If the direction is displayed several seconds after adjustment, the cali-
bration is complete.
Calibrating the compass
1
2
Type A
Type B
23
374
SEQUOIA_OM_USA_OM0C011U
■
Circling calibration
Stop the vehicle in a place where it is safe to drive in a circle.
Press and hold the button for 9 seconds.
“C” appears on the compass display.
Drive the vehicle at 5 mph
(8 km/h) or less in a circle
until a direction is displayed.
If there is not enough space to
drive in a circle, drive around the
block until a direction is dis-
played.
■
Conditions unfavorable to correct operation
The compass may not show the correct direction in the following conditions:
●
The vehicle is stopped immediately after turning.
●
The vehicle is on an inclined surface.
●
The vehicle is in a place where the earth’s magnetic field is subject to inter-
ference by artificial magnetic fields (underground car park/parking lot, under
a steel tower, between buildings, roof car park/parking lot, near an intersec-
tion, near a large vehicle, etc.).
●
The vehicle has become magnetized.
(There is a magnet or metal object near the inside rear view mirror.)
●
The battery has been disconnected.
●
A door is open.
1
2
Type A
Type B
3
375
5
In
SEQUOIA_OM_USA_OM0C011U
WARNING
■
While driving the vehicle
Do not adjust the display. Be sure to adjust the display only when the vehi-
cle is stopped.
■
When doing the circling calibration
Be sure to secure a wide space, and watch out for people and vehicles in
the neighborhood. Do not violate any local traffic rules while performing cir-
cling calibration.
NOTICE
■
To avoid the compass malfunctions
Do not place magnets or any metal objects near the inside rear view mirror.
Doing this may cause a malfunction of the compass sensor.
■
To ensure normal operation of the compass
●
Do not perform circling calibration of the compass in a place where the
earth’s magnetic field is subject to interference by artificial magnetic fields.
●
During calibration, do not operate electric systems (moon roof, power win-
dows, etc.) as they may interfere with the calibration.
377
Maintenance and care
6
SEQUOIA_OM_USA_OM0C011U
6-1. Maintenance and care
Cleaning and protecting
the vehicle exterior. . .. 378
Cleaning and protecting
the vehicle interior. . ... 381
6-2. Maintenance
Maintenance
requirements . . . . ... 384
General maintenance. . 386
Emission inspection and
maintenance (I/M)
programs. . . . . . . 389
6-3. Do-it-yourself
maintenance
Do-it-yourself service
precautions . . . . . . 390
Hood . . . . . . . . . 393
Engine compartment. . . 394
Tires . . . . . . . . .. 405
Tire inflation pressure . ... 416
Wheels . . . . . . . .. 419
Air conditioning filter. . .. 422
Wireless remote control
battery . . . . . . . . 424
Checking and replacing
fuses . . . . . . . ... 426
Light bulbs. . . . . . . 429
378
SEQUOIA_OM_USA_OM0C011U
Cleaning and protecting the vehicle
exterior
● Working from top to bottom, liberally apply water to the vehicle
body, wheel wells and underside of the vehicle to remove any dirt
and dust.
● Wash the vehicle body using a sponge or soft cloth, such as a
chamois.
● For hard-to-remove marks, use car wash soap and rinse thoroughly
with water.
● Wipe away any water.
● Wax the vehicle when the waterproof coating deteriorates.
If water does not bead on a clean surface, apply wax when the vehicle
body is cool.
■
Automatic car washes
●
Fold the mirrors before washing the vehicle. Start washing from the front of
the vehicle. Make sure to extend the mirrors before driving.
●
Brushes used in automatic car washes may scratch the vehicle surface and
harm your vehicle’s paint.
●
In certain automatic car washes, rear spoiler may interfere with machine
operation. This may prevent the vehicle from being cleaned properly or
result in damage to the rear spoiler.
Perform the following to protect the vehicle and maintain it in
prime condition:
379
6-1. Maintenance and care
6
Mainten
SEQUOIA_OM_USA_OM0C011U
■
High pressure car washes
●
Do not allow the nozzles of the car wash to come within close proximity of
the windows.
●
Before using the car wash, check that the fuel filler door on your vehicle is
closed properly.
■
Aluminum wheels
●
Remove any dirt immediately by using a neutral detergent.
●
Wash detergent off with water immediately after use.
●
To protect the paint from damage, make sure to observe the following pre-
cautions.
• Do not use acidic, alkaline or abrasive detergent
• Do not use hard brushes
• Do not use detergent on the wheels when they are hot, such as after driv-
ing or parking in hot weather
■
Bumpers and side moldings
Do not scrub with abrasive cleaners.
WARNING
■
When washing the vehicle
Do not apply water to the inside of the engine compartment. Doing so may
cause the electrical components, etc., to catch fire.
■
Precautions regarding the exhaust pipe
Exhaust gases cause the exhaust pipe to become quite hot.
When washing the vehicle, be careful not to touch the pipe until it has
cooled sufficiently, as touching hot exhaust pipe can cause burns.
■
Precaution regarding the Blind Spot Monitor
If the paint of the rear bumper is chipped or scratched, the system may mal-
function. If this occurs, consult your Toyota dealer.
380
SEQUOIA_OM_USA_OM0C011U
NOTICE
■
To prevent paint deterioration and corrosion on the body and compo-
nents (aluminum wheels, etc.)
●
Wash the vehicle immediately in the following cases:
• After driving near the sea coast
• After driving on salted roads
• If coal tar or tree sap is present on the paint surface
• If dead insects, insect droppings or bird droppings are present on the
paint surface
• After driving in an area contaminated with soot, oily smoke, mine dust,
iron powder or chemical substances
• If the vehicle becomes heavily soiled with dust or mud
• If liquids such as benzene and gasoline are spilled on the paint surface
●
If the paint is chipped or scratched, have it repaired immediately.
●
To prevent the wheels from corroding, remove any dirt and store in a place
with low humidity when storing the wheels.
■
Cleaning the exterior lights
●
Wash carefully. Do not use organic substances or scrub with a hard brush.
This may damage the surfaces of the lights.
●
Do not apply wax to the surfaces of the lights.
Wax may cause damage to the lenses.
■
High pressure car washes
●
When washing the vehicle, do not apply intensive bursts of water to the
camera or camera area. Doing so may result in the camera malfunction-
ing.
●
Do not bring the nozzle tip close to boots (rubber or resin manufactured
cover), connectors or the following parts. The parts may be damaged if
they come into contact with high-pressure water.
• Traction related parts
• Steering parts
• Suspension parts
• Brake parts
381
6-1. Maintenance and care
6
Mainten
SEQUOIA_OM_USA_OM0C011U
Cleaning and protecting the vehicle interior
● Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces
with a cloth dampened with lukewarm water.
● If dirt cannot be removed, wipe it off with a soft cloth dampened with
neutral detergent diluted to approximately 1%.
Wring out any excess water from the cloth and thoroughly wipe off
remaining traces of detergent and water.
● Remove dirt and dust using a vacuum cleaner.
● Wipe off any excess dirt and dust with a soft cloth dampened with
diluted detergent.
Use a diluted water solution of approximately 5% neutral wool detergent.
● Wring out any excess water from the cloth and thoroughly wipe off
all remaining traces of detergent.
● Wipe the surface with a dry, soft cloth to remove any remaining
moisture. Allow the leather to dry in a shaded and ventilated area.
● Remove dirt and dust using a vacuum cleaner.
● Wipe it off with a soft cloth dampened with neutral detergent diluted
to approximately 1%.
● Wring out any excess water from the cloth and thoroughly wipe off
remaining traces of detergent and water.
The following procedures will help protect your vehicle’s interior
and keep it in top condition:
Protecting the vehicle interior
Cleaning the leather areas
Cleaning the synthetic leather areas
382
SEQUOIA_OM_USA_OM0C011U
■
Caring for leather areas
Toyota recommends cleaning the interior of the vehicle at least twice a year to
maintain the quality of the vehicle’s interior.
■
Shampooing the carpets
There are several commercial foaming-type cleaners available. Use a sponge
or brush to apply the foam. Rub in overlapping circles. Do not use water.
Wipe dirty surfaces and let them dry. Excellent results are obtained by keep-
ing the carpet as dry as possible.
■
Seat belts
Clean with mild soap and lukewarm water using a cloth or sponge. Also
check the belts periodically for excessive wear, fraying or cuts.
WARNING
■
Water in the vehicle
●
Do not splash or spill liquid in the vehicle.
Doing so may cause electrical components, etc., to malfunction or catch
fire.
●
Do not get any of the SRS components or wiring in the vehicle interior wet.
(
An electrical malfunction may cause the airbags to deploy or not function
properly, resulting in death or serious injury.
■
Cleaning the interior (especially instrument panel)
Do not use a polish wax or polish cleaner. The instrument panel may reflect
off the windshield, obstructing the driver’s view and leading to an accident,
resulting in death or serious injury.
383
6-1. Maintenance and care
6
Mainten
SEQUOIA_OM_USA_OM0C011U
NOTICE
■
Cleaning detergents
●
Do not use the following types of detergent, as they may discolor the vehi-
cle interior or cause streaks or damage to painted surfaces:
• Non-seat portions: Organic substances such as benzene or gasoline,
alkaline or acidic solutions, dye, and bleach
• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco-
hol
●
Do not use a polish wax or polish cleaner. The instrument panel’s or other
interior part’s painted surface may be damaged.
■
Preventing damage to leather surfaces
Observe the following precautions to avoid damage to and deterioration of
leather surfaces:
●
Remove any dust or dirt from leather surfaces immediately.
●
Do not expose the vehicle to direct sunlight for extended periods of time.
Park the vehicle in the shade, especially during summer.
●
Do not place items made of vinyl, plastic, or containing wax on the uphol-
stery, as they may stick to the leather surface if the vehicle interior heats
up significantly.
■
Water on the floor
Do not wash the vehicle floor with water.
Vehicle systems such as the audio system may be damaged if water comes
into contact with electrical components such as the audio system above or
under the floor of the vehicle. Water may also cause the body to rust.
■
When cleaning the inside of the windshield
Do not allow glass cleaner to contact the lens. Also, do not touch the lens.
(
■
Cleaning the inside of the rear quarter windows and back window
●
Do not use a glass cleaner to clean the rear quarter windows and back
window, as this may cause damage to the rear window defogger heater
wires or antenna. Use a cloth dampened with lukewarm water to gently
wipe the window clean. Wipe the window in strokes running parallel to the
heater wires or antenna.
●
Be careful not to scratch or damage the heater wires or antenna.
384
SEQUOIA_OM_USA_OM0C011U
Maintenance requirements
General maintenance should be performed on a daily basis. This can
be done by yourself or by a Toyota dealer.
Scheduled maintenance should be performed at specified intervals
according to the maintenance schedule.
For details about maintenance items and schedules, refer to the “Sched-
uled Maintenance Guide” or “Owner’s Manual Supplement”.
You can perform some maintenance procedures by yourself.
Please be aware that do-it-yourself maintenance may affect warranty
coverage.
The use of Toyota Repair Manuals is recommended.
For details about warranty coverage, refer to the separate “Owner’s War-
ranty Information Booklet” or “Owner’s Manual Supplement”.
■
Repair and replacement
It is recommended that genuine Toyota parts be used for repairs to ensure
performance of each system. If non-Toyota parts are used in replacement or if
a repair shop other than a Toyota dealer performs repairs, confirm the war-
ranty coverage.
Flex-fuel vehicles: Flex-fuel vehicles use special parts made exclusively for
flex-fuel vehicles. When servicing or repairing your vehicles, use genuine
Toyota parts made exclusively for your flex-fuel vehicle.
To ensure safe and economical driving, day-to-day care and reg-
ular maintenance are essential. It is the owner’s responsibility to
perform regular checks. Toyota recommends the following main-
tenance:
General maintenance
Scheduled maintenance
Do-it-yourself maintenance
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст