Toyota Sequoia (2018 year). Instruction — part 23
353
5-3. Using the storage features
5
In
SEQUOIA_OM_USA_OM0C011U
Type A
Pull the lever upwards to lift the
deck board.
Type B (if equipped)
Open the cover.
Storage compartment
354
5-3. Using the storage features
SEQUOIA_OM_USA_OM0C011U
WARNING
■
When the cargo hooks are not in use
To avoid injury, always return the cargo hooks to their stowed positions.
■
Caution while driving
Keep the auxiliary box closed. Injuries may result in the event of an accident
or sudden braking.
NOTICE
■
To prevent damage to the cargo net hooks
Avoid hanging things other than a cargo net on them.
■
Grocery bag hook weight capacity
Do not hang any object heavier than 8.8 lb. (4 kg) on the grocery bag hooks.
355
5
In
SEQUOIA_OM_USA_OM0C011U
Other interior features
■
Main visor
To set the visor in the forward
position, flip it down.
To set the visor in the side posi-
tion, flip down, unhook, and
swing it to the side.
To use the side extender, place
the visor in the side position,
then slide it backward.
■
Sub visor (if equipped)
Flip it down.
Sun visors
356
SEQUOIA_OM_USA_OM0C011U
Vehicles without vanity light
Open the cover.
Vehicles with vanity light
Open the cover.
The light turns on when the cover
is opened.
Adjust the brightness of the
light.
Vanity mirrors
NOTICE
To prevent battery discharge, do not leave the vanity lights on for extended
periods while the engine is not running.
357
5
In
SEQUOIA_OM_USA_OM0C011U
■
12 V DC
Please use as a power supply for electronic goods that use less than
12 VDC/10 A (power consumption of 120 W).
When using electronic goods, make sure that the power consumption
of all the connected power outlets is less than 120 W.
Power outlets
Instrument panel
Front console box (outside)
(if equipped)
Open the lid.
Open the lid.
Luggage compartment
Open the lid.
358
SEQUOIA_OM_USA_OM0C011U
Front console box (inside)
Lift the lid while pulling up the
knob to release the lock.
Open the lid.
■
120 V AC (if equipped)
Accessories that use less than 100 W.
Open the lid.
1
2
359
5
In
SEQUOIA_OM_USA_OM0C011U
■
The power outlets can be used when
12 V DC
The engine switch is in the “ACC” or “ON” position.
120 V AC
The engine switch is in the “ON” position.
NOTICE
●
To avoid damaging the power outlets, close the power outlet lid when the
power outlet is not in use.
Foreign objects or liquids that enter the power outlet may cause a short
circuit.
●
To prevent blown fuse:
12 V DC
Do not use an accessory that uses more than 12 V 10 A.
120 V AC
Do not use a 120 V AC appliance that requires more than 100 W.
If a 120 V AC appliance that consumes more than 100 W is used, the pro-
tection circuit will cut the power supply.
●
To prevent battery discharge, do not use the power outlet longer than nec-
essary when the engine is not running.
●
The following 120 V AC appliances may not operate properly even if their
power consumption is under 100 W:
• Appliances with high initial peak wattage
• Measuring devices that process precise data
• Other appliances that require an extremely stable power supply
360
SEQUOIA_OM_USA_OM0C011U
Push the lid.
The mirror can be adjusted by
pushing the mirror edge.
Conversation mirror
1
2
WARNING
■
Caution while driving
Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and an accident, resulting
in death or serious injury.
361
5
In
SEQUOIA_OM_USA_OM0C011U
Separated type
Adjusting to the desired angle:
Lower the armrest from the
highest position to the lowest
position.
Raise the armrest to the
desired angle.
Unlock the armrest:
Lift the armrest to raise it to the
highest position.
Bench type
Pull the armrest down for use.
Armrest (second seats)
1
2
NOTICE
To prevent damage to the armrest, do not apply too much load or sit on the
armrest.
362
SEQUOIA_OM_USA_OM0C011U
Pull the tab up.
Hook the sunshade onto the anchors.
To lower the sunshade, pull the tab slightly to unhook the shade, and lower
it slowly.
Rear side sunshades (if equipped)
Rear door window
Rear quarter window
NOTICE
●
To ensure normal operation of the sunshade, observe the following pre-
cautions.
• Do not place anything where it may hinder the opening/closing of the
sunshade.
• Do not place anything on the sunshade.
363
5
In
SEQUOIA_OM_USA_OM0C011U
An assist grip (type A) installed on the ceiling can be used to support
your body while sitting on the seat.
An assist grip (type B) installed on the pillar can be used when getting
in or out of the vehicle and others.
Assist grip (type A)
Assist grip (type B)
Assist grips
WARNING
Do not use the assist grip (type A) when getting in or out of the vehicle or
rising from your seat.
NOTICE
To prevent damage to the assist grip, do not hang any heavy object or put a
heavy load on the assist grip.
364
SEQUOIA_OM_USA_OM0C011U
Garage door opener
∗
The HomeLink
®
wireless control system in your vehicle has 3 buttons
which can be programmed to operate 3 different devices. Refer to the
programming methods on the following pages to determine the
method which is appropriate for the device.
HomeLink
®
indicator light
Garage door operation indica-
tors
Buttons
■
Before programming the HomeLink
®
● During programming, it is possible that garage doors, gates, or
other devices may operate. For this reason, make sure that peo-
ple and objects are clear of the garage door or other devices to
prevent injury or other potential harm.
● It is recommended that a new battery be placed in the remote
control transmitter for more accurate programming.
● Garage door opener motors manufactured after 1995 may be
equipped with rolling code protection. If this is the case, you may
need a stepladder or other sturdy, safe device to reach the
“Learn” or “Smart” button on the garage door opener motor.
∗
: If equipped
The garage door opener can be programmed to operate garage
doors, gates, entry doors, door locks, home lighting systems,
security systems, and other devices.
HomeLink
®
365
5
In
SEQUOIA_OM_USA_OM0C011U
■
Programming the HomeLink
®
Steps
through
must be performed within 60 seconds, otherwise
the indicator light will stop flashing and programming will not be able to be
completed.
Press and release the HomeLink
®
button you want to program
and check that the HomeLink
®
indicator light flashes orange.
Point the remote control
transmitter for the device at
the rear view mirror, 1 to 3 in.
(25 to 75 mm) from the
HomeLink
®
buttons.
Keep the HomeLink
®
indicator
light in view while programming.
Program a device.
Programming a device other than an entry gate (for U.S.A.
owners)
Press and hold the remote control transmitter button until the
HomeLink
®
indicator light changes from slowly flashing orange to
rapidly flashing green (rolling code) or continuously lit green
(fixed code), then release the button.
Programming an entry gate (for U.S.A. owners)/Programming
a device in the Canadian market
Press and release the remote control transmitter button at 2 sec-
ond intervals, repeatedly, until the HomeLink
®
indicator light
changes from slowly flashing orange to rapidly flashing green
(rolling code) or continuously lit green (fixed code).
1
3
1
2
3
366
SEQUOIA_OM_USA_OM0C011U
Test the HomeLink
®
operation by pressing the newly pro-
grammed button and observing the indicator light:
● Indicator light illuminates: Programming of a fixed code device
has completed. The garage door or other device should operate
when a HomeLink
®
button is pressed and released.
● Indicator light flashes rapidly: The garage door opener motor or
other device is equipped with a rolling code. To complete pro-
gramming, firmly press and hold the HomeLink
®
button for 2 sec-
onds then release it.
● If the garage door or other device does not operate, proceed to
“Programming a rolling code system”.
Repeat the steps above to program another device for any of
the remaining HomeLink
®
buttons.
■
Programming a rolling code system
2 or more people may be necessary to complete rolling code pro-
gramming.
Locate the “Learn” or “Smart”
button on the garage door
opener motor in the garage.
This button can usually be found
where the hanging antenna wire
is attached to the unit. The
name and color of the button
may vary by manufacturer.
Refer to the Owner’s manual
supplied with the garage door
opener motor for details.
Press and release the
“Learn” or “Smart” button.
Perform
within 30 sec-
onds after performing
.
4
5
1
2
3
2
367
5
In
SEQUOIA_OM_USA_OM0C011U
Press and hold the desired
HomeLink
®
button (inside the
vehicle) for 2 seconds and
release it. Repeat this
sequence (press/hold/
release) up to 3 times to
complete programming.
If the garage door opener
motor operates when the
HomeLink
®
button is
pressed, the garage door
opener motor recognizes the
HomeLink
®
signal.
■
Enabling 2-way communication with a garage door (only avail-
able for compatible devices)
When enabled, 2-way communication allows you to check the sta-
tus of the opening and closing of a garage door through indicators
in your vehicle.
2-way communication is only available if the garage door opener
motor used is a compatible device. (To check device compatibility,
refer to www.HomeLink.com.)
Within 5 seconds after programming the garage door opener has
been completed, if the garage door opener motor is trained to
HomeLink
®
, both garage door operation indicators will flash rap-
idly green and the light on the garage door opener motor will
blink twice, indicating that 2-way communication is enabled.
If the indicators do not flash, perform
and
within the first 10
presses of the HomeLink
®
button after programming has been
completed.
3
1
2
3
368
SEQUOIA_OM_USA_OM0C011U
Press a programmed HomeLink
®
button to operate a garage
door.
Within 1 minute of pressing the HomeLink
®
button, after the
garage door operation has stopped, press the “Learn” or “Smart”
button on the garage door opener motor. Within 5 seconds of the
establishment of 2-way communication with the garage door
opener, both garage door operation indicators in the vehicle will
flash rapidly green and the light on the garage door opener motor
will blink twice, indicating that 2-way communication is enabled.
■
Reprogramming a single HomeLink
®
button
When the following procedure is performed, buttons which already
have devices registered to them can be overwritten:
With one hand, press and hold the desired HomeLink
®
button.
When the HomeLink
®
indicator starts flashing orange, continue
to hold the HomeLink
®
button and perform “Programming the
HomeLink
®
”
(it takes 20 seconds for the HomeLink
®
indicator
to start flashing).
Press the appropriate HomeLink
®
button. The HomeLink
®
indicator
light should turn on.
Operating the HomeLink
®
2
3
1
2
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст