Toyota RM06H0E engine. Manual — part 8
Upper Housing
Lock Housing
Lower
Housing
Upper Housing Attached Lock Housing
Wire
Pull
B–45
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
61
Wire Harness Repair Manual
Insulation Displacement Connector (0.64 Type)
(a)
Install the upper housing to the lock housing.
NOTICE:
D
Securely Lock it.
D
Be careful not to mistake the upper housing and
lower housing when putting together.
(b)
Make the projection of the front lock of the upper
housing attached lock housing meet the ditch of the
front lock of the lower housing and fix the rear lock.
NOTICE:
D
Afteruniting, securely lock it for not leaving the rear
lock arm deformed.
D
Make sure that the terminals will not become loose
by pulling the wires lightily.
D
Be careful not to mistake the upper housing and
lower housing when putting together.
3.
When properly installed, pulling gently on the
wire lead will prove the terminal is locked in the
connector.
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
B–46
62
Wire Harness Repair Manual
NOTICE:
If you working on the waterproof type, make sure that
a rubber plug or a terminal gasket is inserted into the
housing securely.
4.
Secure the Repaired Wire to the Harness
If the wire is not in the conduit, or secured by other
means, wrap vinyl tape around the bundle to keep it
together with the other wires.
5.
Connect Connector
D
Fit the male connector to the female terminal.
NOTICE:
D
Do not twist the connector when fitting.
D
Insert it until fully locked.
Lever
Lever
B–47
TERMINAL AND CONNECTOR REPAIR–HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS
63
Wire Harness Repair Manual
HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS
Low Fit and Lever Type Connector
[Case 1]
1.
Cut the connection of the connector
(1)
Push the place indicated by the arrow.
(2)
The lock is released and lever is lifted up.
(3)
Lift the lever up until it stops.
(4)
Cut the connection of the connector.
NOTICE:
Do not hold the wire harness to pull it.
2.
Connect the connector
(1)
Connect the connector in the condition that the lever
is fully lifted up.
HINT:
If the lever is locked at the lower position, follow
the procedure [Case 1]. (1) to (3) and lift the lever up fully.
Lever
Lever is not locked
Lever
TERMINAL AND CONNECTOR REPAIR–HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS
B–48
64
Wire Harness Repair Manual
(2)
Hold the connector to prevent it from slip off and push
it down until you hear a click to lock it.
(3)
Confirm that the lever is securely locked.
[Case 2]
1.
Cut the connection of the connector
(1)
Hold the area indicated by the arrow in the illustration
(2)
The lock is released and the lever is lifted up.
(3)
Lift the lever up fully.
(4)
Cut the connection of the connector.
NOTICE:
Do not hold the wire harness to pull it.
Lever
Lever is not locked
Lever
B–49
TERMINAL AND CONNECTOR REPAIR–HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS
65
Wire Harness Repair Manual
2.
Connect the connector
(1)
Connect the connector in the condition that the lever
is fully lifted up.
(2)
Hold the connector to prevent it from slip off and push
it down until you hear a click to lock it.
(3)
Confirm that the lever is securely locked.
[Case 3]
1.
Cut the connection of the connector
(1)
Pick the part indicated in the illustration by fingers.
(2)
The lock is released and the lever is lifted up.
(3)
Lift the lever up fully.
Lever
Lever is not locked
TERMINAL AND CONNECTOR REPAIR–HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS
B–50
66
Wire Harness Repair Manual
(4)
Cut the connection of the connector.
NOTICE:
Do not hold the wire harness to pull it.
2.
Connect the connector
(1)
Connect the connector in the condition that the lever
is fully lifted up.
HINT:
If the lever is locked at the lower position, follow
the procedure [Case 3]. (1) to (3) and lift the lever up fully.
(2)
Hold the connector to prevent it from slip off and push
it down until you hear a click to lock it.
(3)
Confirm that the lever is securely fitted
Coil spring
Pin
Convex part
Double
locking
device pin
Primary locking
device
Lock
Lock
B–51
TERMINAL AND CONNECTOR REPAIR–HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS
67
Wire Harness Repair Manual
The connector with secondary locking
device
1.
Area used
D
Wire harness for SRS airbag deployment
2.
Cut the connection of the connector.
(1)
Release the double locking.
(2)
Release the primary locking and separate the
connector.
NOTICE:
Do not hold the wire harness to pull it.
3.
Connect the connector
(1)
Install the primary locking device and connect the
connector.
(2)
Install the double locking device.
NOTICE:
The double locking device can not be installed unless
the primary locking device is installed.
Connector A
Connector B
Connector A
Lass than 1mm
Connector B
Bolt
Cross–section of the bolt
TERMINAL AND CONNECTOR REPAIR–HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS
B–52
68
Wire Harness Repair Manual
Connector fixed by bolts
1.
Area used
D
Engine control computer harness
2.
Cut the connection of the connector.
(1)
Remove the connector A.
(2)
Loose the bolt using a tool like driver until the
connector B can be removed by hand and separate
the connector.
HINT:
If the bolt can not be removed, roll it while pulling
forward.
3.
Connection of the connector
(1)
Temporarily fit the connector B.
(2)
Tighten the bolt by using tool like driver and fit the
connector B completely.
NOTICE:
D
Tighten the bolt until feeling it lighter. Then confirm
that the width of chink of the connector B is less
than 1mm.
D
The bolt can be rolled after it is fitted.
D
If the impact wrench is used, do not let it rolling
more than three seconds. (The housing may be
deformed by generated heat)
D
Be sure and connect the connector B straight. Do
not incline it while connecting.
(3)
Connect the connector A.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст