Toyota Camry Hybrid (2020 year). Manual in english — part 7
398
6-2. Maintenance
General maintenance should be performed on a daily basis. This can
be done by yourself or by a Toyota dealer.
Scheduled maintenance should be performed at specified intervals
according to the maintenance schedule.
For details about maintenance items and schedules, refer to the “Sched-
uled Maintenance Guide” or “Owner’s Manual Supplement”.
You can perform some maintenance procedures by yourself.
Please be aware that do-it-yourself maintenance may affect warranty
coverage.
The use of Toyota Repair Manuals is recommended.
For details about warranty coverage, refer to the separate “Owner’s War-
ranty Information Booklet” or “Owner’s Manual Supplement”.
Maintenance requirements
To ensure safe and economical driving, day-to-day care and reg-
ular maintenance are essential. It is the owner’s responsibility to
perform regular checks. Toyota recommends the following main-
tenance:
General maintenance
Scheduled maintenance
Do-it-yourself maintenance
-------------------------------------------------------------------------------------------------------------------------------------------------------------
399
6-2. Maintenance
6
Mai
ntenan
ce and care
■
Repair and replacement
It is recommended that genuine Toyota parts be used for repairs to ensure
performance of each system. If non-Toyota parts are used in replacement or if
a repair shop other than a Toyota dealer performs repairs, confirm the war-
ranty coverage.
■
Resetting the message indicating maintenance is required
After the required maintenance is preformed according to the maintenance
schedule, please reset the message.
To reset the message, perform the following procedure:
Select
(4.2-inch display) or
(7-inch display) on the multi-information
display using the meter control switches on the steering wheel.
(
4.2-inch display: Select “Vehicle Settings” and then press
.
7-inch display: Select
and then press and hold
.
Select “Scheduled Maintenance” and then press
.
Select “Yes” and then press
.
A message will be displayed on the multi-information display when the
reset procedure has been completed.
■
Allow inspection and repairs to be performed by a Toyota dealer
●
Toyota technicians are well-trained specialists and are kept up to date with
the latest service information. They are well informed about the operations
of all systems on your vehicle.
●
Keep a copy of the repair order. It proves that the maintenance that has
been performed is under warranty coverage. If any problem should arise
while your vehicle is under warranty, your Toyota dealer will promptly take
care of it.
1
2
3
4
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
400
6-2. Maintenance
WARNING
■
If your vehicle is not properly maintained
Improper maintenance could result in serious damage to the vehicle and
possible death or serious injury.
■
Important health and safety information
●
Engine exhaust, some of its constituents, and a wide variety of automobile
components contain or emit chemicals known to the State of California to
cause cancer and birth defects and other reproductive harm. Work in a
well ventilated area.
●
Oils, fuels and fluids contained in vehicles as well as waste produced by
component wear contain or emit chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
Avoid exposure and wash any affected area immediately.
●
12-volt battery posts, terminals and related accessories contain lead and
lead compounds which are known to cause brain damage. Wash your
hands after handling. (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
401
6-2. Maintenance
6
Mai
ntenan
ce and care
General maintenance
Listed below are the general maintenance items that should be
performed at the intervals specified in the “Owner’s Warranty
Information Booklet” or “Owner’s Manual Supplement/Sched-
uled Maintenance Guide”. It is recommended that any problem
you notice should be brought to the attention of your Toyota
dealer or qualified service shop for advice.
Engine compartment
Items
Check points
Brake fluid
Is the brake fluid at the correct
level?
(
Coolant
Is the coolant at the correct level?
(
Engine oil
Is the engine oil at the correct level?
(
Exhaust system
There should not be any fumes or
strange sounds.
Radiator/condenser
The radiator and condenser should
be free from foreign objects.
(
Washer fluid
Is there sufficient washer fluid?
(
Trunk
Items
Check points
12-volt battery
Check the connections. (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
402
6-2. Maintenance
Vehicle interior
Items
Check points
Accelerator pedal
• The accelerator pedal should
move smoothly (without uneven
pedal effort or catching).
Hybrid transmission “Park” mecha-
nism
• When parked on a slope and the
shift lever is in P, is the vehicle
securely stopped?
Brake pedal
• Does the brake pedal move
smoothly?
• Does the brake pedal have appro-
priate clearance from the floor?
(
• Does the brake pedal have the
correct amount of free play?
(
Brakes
• The vehicle should not pull to one
side when the brakes are applied.
• The brakes should work effec-
tively.
• The brake pedal should not feel
spongy.
• The brake pedal should not get
too close to the floor when the
brakes are applied.
Head restraints (adjustable type)
• Do the head restraints move
smoothly and lock securely?
Indicators/buzzers
• Do the indicators and buzzers
function properly?
Lights
• Do all the lights come on?
Parking brake
• Does the parking brake operate
normally?
• When parked on a slope and the
parking brake is on, is the vehicle
securely stopped?
-------------------------------------------------------------------------------------------------------------------------------------------------------------
403
6-2. Maintenance
6
Mai
ntenan
ce and care
Seat belts
• Do the seat belts operate
smoothly?
• The seat belts should not be dam-
aged.
Seats
• Do the seat controls operate prop-
erly?
Steering wheel
• Does the steering wheel rotate
smoothly?
• Does the steering wheel have the
correct amount of free play?
• There should not be any strange
sounds coming from the steering
wheel.
Vehicle exterior
Items
Check points
Items
Check points
Doors/trunk
• Do the doors/trunk operate
smoothly?
Engine hood
• Does the engine hood lock system
work properly?
Fluid leaks
• There should not be any signs of
fluid leakage after the vehicle has
been parked.
Tires
• Is the tire inflation pressure cor-
rect?
• The tires should not be dam-
aged or excessively worn.
• Have the tires been rotated
according to the maintenance
schedule?
• The wheel nuts should not be
loose.
Windshield wipers
• The wiper blades should not show
any signs of cracking, splitting,
wear, contamination or deforma-
tion.
• The wiper blades should clear the
windshield without streaking or
skipping.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
404
6-2. Maintenance
WARNING
■
If the hybrid system is operating
Turn the hybrid system off and ensure that there is adequate ventilation
before performing maintenance checks.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
405
6-2. Maintenance
6
Mai
ntenan
ce and care
The OBD system determines that a problem exists somewhere in the
emission control system. Your vehicle may not pass the I/M test and
may need to be repaired. Contact your Toyota dealer to service the
vehicle.
●
When the 12-volt battery is disconnected or discharged
Readiness codes that are set during ordinary driving are erased.
Also, depending on your driving habits, the readiness codes may
not be completely set.
●
When the fuel tank cap is loose
The malfunction indicator lamp comes on indicating a temporary
malfunction and your vehicle may not pass the I/M test.
The error code in the OBD system will not be cleared unless the vehi-
cle is driven 40 or more times.
Contact your Toyota dealer to prepare the vehicle for re-testing.
Emission inspection and maintenance (I/M)
programs
Some states have vehicle emission inspection programs which
include OBD (On Board Diagnostics) checks. The OBD system
monitors the operation of the emission control system.
If the malfunction indicator lamp comes on
Your vehicle may not pass the I/M test in the following situations:
When the malfunction indicator lamp still remains on after sev-
eral driving trips
If your vehicle does not pass the I/M test
-------------------------------------------------------------------------------------------------------------------------------------------------------------
406
6-3. Do-it-yourself maintenance
Do-it-yourself service precautions
If you perform maintenance by yourself, be sure to follow the
correct procedure as given in these sections.
Items
Parts and tools
12-volt
battery
condition
(
• Grease
• Conventional wrench (for terminal clamp bolts)
Brake fluid level
(
• FMVSS No.116 DOT 3 or SAE J1703 brake fluid
• Rag or paper towel
• Funnel (used only for adding brake fluid)
Engine/power
control unit cool-
ant level
(
• “Toyota Super Long Life Coolant” or a similar high
quality ethylene glycol-based non-silicate, non-
amine, non-nitrite and non-borate coolant with long-
life hybrid organic acid technology
U.S.A.:
“Toyota Super Long Life Coolant” is pre-mixed with
50% coolant and 50% deionized water.
Canada:
“Toyota Super Long Life Coolant” is pre-mixed with
55% coolant and 45% deionized water.
• Funnel (used only for adding coolant)
Engine oil level
(
• “Toyota Genuine Motor Oil” or equivalent
• Rag or paper towel
• Funnel (used only for adding engine oil)
Fuses (
• Fuse with same amperage rating as original
Hybrid
battery
(traction battery)
air intake vent
(
• Vacuum cleaner, etc.
• Phillips screwdriver
Light bulbs
(
• Bulb with same number and wattage rating as origi-
nal
• Flathead screwdriver
• Wrench
Radiator/con-
denser (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
407
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Tire
inflation
pressure
(
• Tire pressure gauge
• Compressed air source
Washer fluid
(
• Water or washer fluid containing antifreeze (for win-
ter use)
• Funnel (used only for adding water or washer fluid)
WARNING
The engine compartment contains many mechanisms and fluids that may
move suddenly, become hot, or become electrically energized. To avoid death
or serious injury, observe the following precautions.
■
When working on the engine compartment
●
Make sure that the “READY” indicator is off.
●
Keep hands, clothing and tools away from the moving fan and engine
drive belt.
●
Be careful not to touch the engine, power control unit, radiator, exhaust
manifold, etc. right after driving as they may be hot. Oil and other fluids
may also be hot.
●
Do not leave anything that may burn easily, such as paper and rags, in the
engine compartment.
●
Do not smoke, cause sparks or expose an open flame to fuel. Fuel fumes
are flammable.
■
When working near the electric cooling fan or radiator grille
Be sure the power switch is off.
With the power switch in ON mode, the electric cooling fan may automati-
cally start to run if the air conditioning is on and/or the coolant temperature
is high. (
■
Safety glasses
Wear safety glasses to prevent flying or falling material, fluid spray, etc.
from getting in your eyes.
NOTICE
■
If you remove the air cleaner filter
Driving with the air cleaner filter removed may cause excessive engine wear
due to dirt in the air.
Items
Parts and tools
-------------------------------------------------------------------------------------------------------------------------------------------------------------
408
6-3. Do-it-yourself maintenance
Pull the hood lock release lever.
The hood will pop up slightly.
Pull up the auxiliary catch lever
and lift the hood.
■
Open hood warning buzzer
If the vehicle reaches a speed of 3 mph (5 km/h), the master warning light
flashes and a buzzer sounds to indicate that the hood is not fully closed.
Hood
Release the lock from the inside of the vehicle to open the hood.
1
2
WARNING
■
Pre-driving check
Check that the hood is fully closed and locked.
If the hood is not locked properly, it may open while the vehicle is in motion
and cause an accident, which may result in death or serious injury.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
409
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
◆
Front
◆
Rear
Positioning a floor jack
When using a floor jack, follow the instructions in the manual
provided with the jack and perform the operation safely.
When raising your vehicle with a floor jack, position the jack cor-
rectly. Improper placement may damage your vehicle or cause
injury.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
410
6-3. Do-it-yourself maintenance
Engine compartment
Fuse boxes
(
Engine oil filler cap (
Engine oil level dipstick
(
Brake fluid reservoir
(
Radiator
(
Electric cooling fan
Condenser
(
Power control unit
coolant reservoir
(
Engine coolant reservoir
(
Washer fluid tank (
1
2
3
4
5
6
7
8
9
10
-------------------------------------------------------------------------------------------------------------------------------------------------------------
411
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
With the engine at operating temperature and turned off, check the oil
level on the dipstick.
■
Checking the engine oil
Park the vehicle on level ground. After warming up the engine
and turning it off the hybrid system, wait more than 5 minutes for
the oil to drain back into the bottom of the engine.
Holding a rag under the end,
pull the dipstick out.
Wipe the dipstick clean.
Reinsert the dipstick fully.
Holding a rag under the end, pull the dipstick out and check the
oil level.
Low
Normal
Excessive
The shape of the dipstick may
differ depending on the type of
vehicle or engine.
Wipe the dipstick and reinsert it fully.
Engine oil
1
2
3
4
5
1
2
3
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
412
6-3. Do-it-yourself maintenance
■
Adding engine oil
If the oil level is below or near
the low level mark, add engine
oil of the same type as that
already in the engine.
Make sure to check the oil type and prepare the items needed
before adding oil.
Remove the oil filler cap by turning it counterclockwise.
Add engine oil slowly, checking the dipstick.
Install the oil filler cap by turning it clockwise.
■
Engine oil consumption
A certain amount of engine oil will be consumed while driving. In the following
situations, oil consumption may increase, and engine oil may need to be
refilled in between oil maintenance intervals.
●
When the engine is new, for example directly after purchasing the vehicle or
after replacing the engine
●
If low quality oil or oil of an inappropriate viscosity is used
●
When driving at high engine speeds or with a heavy load, or when driving
while accelerating or decelerating frequently
●
When leaving the engine idling for a long time, or when driving frequently
through heavy traffic
Engine oil selection
Oil quantity
(Low
Full)
1.6 qt. (1.5 L, 1.3 Imp. qt.)
Items
Clean funnel
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
413
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
WARNING
■
Used engine oil
●
Used engine oil contains potentially harmful contaminants which may
cause skin disorders such as inflammation and skin cancer, so care
should be taken to avoid prolonged and repeated contact. To remove used
engine oil from your skin, wash thoroughly with soap and water.
●
Dispose of used oil and filters only in a safe and acceptable manner. Do
not dispose of used oil and filters in household trash, in sewers or onto the
ground.
Call your Toyota dealer, service station or auto parts store for information
concerning recycling or disposal.
●
Do not leave used engine oil within the reach of children.
NOTICE
■
To prevent serious engine damage
Check the oil level on a regular basis.
■
When replacing the engine oil
●
Be careful not to spill engine oil on the vehicle components.
●
Avoid overfilling, or the engine could be damaged.
●
Check the oil level on the dipstick every time you refill the vehicle.
●
Be sure the engine oil filler cap is properly tightened.
■
If oil is spilled on the engine cover
To prevent the engine cover from being damaged, remove any engine oil
from the engine cover as soon as possible using a neutral detergent.
Do not use an organic solvent such as brake cleaner.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
414
6-3. Do-it-yourself maintenance
Engine coolant reservoir
The coolant level is satisfactory if it is between the “F” and “L” lines on
the reservoir when the hybrid system is cold.
Reservoir cap
“F” line
“L” line
If the level is on or below the “L”
line, add coolant up to the “F” line.
(
Power control unit coolant reservoir
The coolant level is satisfactory if it is between the “FULL” and “LOW”
lines on the reservoir when the hybrid system is cold.
Reservoir cap
“FULL” line
“LOW” line
If the level is on or below the
“LOW” line, add coolant up to the
“FULL” line. (
■
Coolant selection
Only use “Toyota Super Long Life Coolant” or a similar high quality ethylene
glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with
long-life hybrid organic acid technology.
U.S.A.:
“Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion-
ized water. (Minimum temperature: -31
F [-35
C])
Canada:
“Toyota Super Long Life Coolant” is a mixture of 55% coolant and 45% deion-
ized water. (Minimum temperature: -44
F [-42
C])
For more details about coolant, contact your Toyota dealer.
Coolant
1
2
3
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
415
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
If the coolant level drops within a short time of replenishing
Visually check the radiators, hoses, engine/power control unit coolant reser-
voir caps, drain cock and water pump.
If you cannot find a leak, have your Toyota dealer test the cap and check for
leaks in the cooling system.
Check the radiator and condenser and clear away any foreign objects.
If either of the above parts is extremely dirty or you are not sure of
their condition, have your vehicle inspected by your Toyota dealer.
WARNING
■
When the hybrid system is hot
Do not remove the engine/power control unit coolant reservoir caps or the
radiator cap.
The cooling system may be under pressure and may spray hot coolant if the
cap is removed, causing serious injuries, such as burns.
NOTICE
■
When adding coolant
Coolant is neither plain water nor straight antifreeze. The correct mixture of
water and antifreeze must be used to provide proper lubrication, corrosion
protection and cooling. Be sure to read the antifreeze or coolant label.
■
If you spill coolant
Be sure to wash it off with water to prevent it from damaging parts or paint.
Radiator and condenser
WARNING
■
When the hybrid system is hot
Do not touch the radiator or condenser as they may be hot and cause seri-
ous injuries, such as burns.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
416
6-3. Do-it-yourself maintenance
■
Checking fluid level
The brake fluid level should be
between the “MAX” and “MIN”
lines on the tank.
“MAX”
“MIN”
■
Adding fluid
Make sure to check the fluid type and prepare the necessary item.
■
Brake fluid can absorb moisture from the air
Excess moisture in the brake fluid can cause a dangerous loss of braking effi-
ciency. Use only newly opened brake fluid.
Brake fluid
1
2
Fluid type
FMVSS No.116 DOT 3 or SAE J1703 brake fluid
Item
Clean funnel
WARNING
■
When filling the reservoir
Take care as brake fluid can harm your hands and eyes and damage
painted surfaces.
If fluid gets on your hands or in your eyes, flush the affected area with clean
water immediately.
If you still experience discomfort, see a doctor.
NOTICE
■
If the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads
wear out or when the fluid level in the accumulator is high.
If the reservoir needs frequent refilling, there may be a serious problem.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
417
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Add washer fluid in the following
situations:
●
A washer does not work.
●
“Windshield Washer Fluid Low”
is displayed on the multi-infor-
mation display.
Washer fluid
WARNING
■
When adding washer fluid
Do not add washer fluid when the hybrid system is hot or operating as
washer fluid contains alcohol and may catch fire if spilled on the engine, etc.
NOTICE
■
Do not use any fluid other than washer fluid
Do not use soapy water or engine antifreeze instead of washer fluid.
Doing so may cause streaking on the vehicle's painted surfaces, as well as
damaging the pump leading to problems of the washer fluid not spraying.
■
Diluting washer fluid
Dilute washer fluid with water as necessary.
Refer to the freezing temperatures listed on the label of the washer fluid bot-
tle.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
418
6-3. Do-it-yourself maintenance
The 12-volt battery is located on
the right-hand side of the trunk.
Remove the 12-volt battery cover.
12-volt battery
Location
Removing the 12-volt battery cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
419
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Make sure that the 12-volt battery terminals are not corroded and that
there are no loose connections, cracks, or loose clamps.
Terminals
Hold-down clamp
■
Before recharging
When recharging, the 12-volt battery produces hydrogen gas which is flam-
mable and explosive. Therefore, observe the following precautions before
recharging:
●
If recharging with the 12-volt battery installed on the vehicle, be sure to dis-
connect the ground cable.
●
Make sure the power switch on the charger is off when connecting and dis-
connecting the charger cables to the 12-volt battery.
■
After recharging/reconnecting the 12-volt battery
●
Unlocking the doors using the smart key system may not be possible imme-
diately after reconnecting the 12-volt battery. If this happens, use the wire-
less remote control or the mechanical key to lock/unlock the doors.
●
Start the hybrid system with the power switch in ACCESSORY mode. The
hybrid system may not start with the power switch turned off. However, the
hybrid system will operate normally from the second attempt.
●
The power switch mode is recorded by the vehicle. If the 12-volt battery is
reconnected, the vehicle will return the power switch mode to the status it
was in before the 12-volt battery was disconnected. Make sure to turn off
the power before disconnecting the 12-volt battery. Take extra care when
connecting the 12-volt battery if the power switch mode prior to discharge is
unknown.
If the system will not start even after multiple attempts, contact your Toyota
dealer.
Exterior
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
420
6-3. Do-it-yourself maintenance
WARNING
■
Chemicals in the 12-volt battery
The 12-volt battery contains poisonous and corrosive sulfuric acid and may
produce hydrogen gas which is flammable and explosive. To reduce the risk
of death or serious injury, take the following precautions while working on or
near the 12-volt battery:
●
Do not cause sparks by touching the 12-volt battery terminals with tools.
●
Do not smoke or light a match near the 12-volt battery.
●
Avoid contact with eyes, skin and clothes.
●
Never inhale or swallow electrolyte.
●
Wear protective safety glasses when working near the 12-volt battery.
●
Keep children away from the 12-volt battery.
■
Where to safely charge the 12-volt battery
Always charge the 12-volt battery in an open area. Do not charge the 12-
volt battery in a garage or closed room where there is insufficient ventila-
tion.
■
How to recharge the 12-volt battery
Only perform a slow charge (5 A or less). The 12-volt battery may explode if
charged at a quicker rate.
■
Emergency measures regarding electrolyte
●
If electrolyte gets in your eyes
Flush your eyes with clean water for at least 15 minutes and get immedi-
ate medical attention. If possible, continue to apply water with a sponge or
cloth while traveling to the nearest medical facility.
●
If electrolyte gets on your skin
Wash the affected area thoroughly. If you feel pain or burning, get medical
attention immediately.
●
If electrolyte gets on your clothes
It can soak through clothing on to your skin. Immediately take off the cloth-
ing and follow the procedure above if necessary.
●
If you accidentally swallow electrolyte
Drink a large quantity of water or milk. Get emergency medical attention
immediately.
■
When disconnecting the 12-volt battery
Do not disconnect the negative (-) terminal on the body side. The discon-
nected negative (-) terminal may touch the positive (+) terminal, which may
cause a short and result in death or serious injury.
■
When replacing the 12-volt battery
Use a 12-volt battery designed for this vehicle. Failure to do so may cause
gas (hydrogen) to enter the passenger compartment, causing a fire or
explosion.
For replacement of the 12-volt battery, contact your Toyota dealer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
421
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
NOTICE
■
When recharging the 12-volt battery
Never recharge the 12-volt battery while the hybrid system is operating.
Also, be sure all accessories are turned off.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
422
6-3. Do-it-yourself maintenance
Check if the treadwear indicators are showing on the tires. Also check
the tires for uneven wear, such as excessive wear on one side of the
tread.
Check the spare tire condition and pressure if not rotated.
New tread
Worn tread
Treadwear indicator
The location of treadwear indicators is shown by a “TWI” or “
” mark,
etc., molded into the sidewall of each tire.
Replace the tires if the treadwear indicators are showing on a tire.
Rotate the tires in the order
shown.
To equalize tire wear and extend
tire life, Toyota recommends that
tire rotation is carried out at the
same interval as tire inspection.
Do not fail to initialize the tire
pressure warning system after
tire rotation.
Tires
Replace or rotate tires in accordance with maintenance sched-
ules and treadwear.
Checking tires
Tire rotation
1
2
3
Front
-------------------------------------------------------------------------------------------------------------------------------------------------------------
423
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Your vehicle is equipped with a tire pressure warning system that uses
tire pressure warning valve and transmitters to detect low tire inflation
pressure before serious problems arise.
Vehicles without a tire inflation pressure display function
If the tire pressure drops below a predetermined level, the driver is
warned by a screen display and a warning light. (
Vehicles with a tire inflation pressure display function
●
The tire pressure detected by the tire pressure warning system can
be displayed on the multi-information display.
●
If the tire pressure drops below a predetermined level, the driver is
warned by a screen display and a warning light. (
Tire pressure warning system
4.2-inch display
7-inch display
4.2-inch display
7-inch display
-------------------------------------------------------------------------------------------------------------------------------------------------------------
424
6-3. Do-it-yourself maintenance
◆
Installing tire pressure warning valves and transmitters
When replacing the tires or wheels, the tire pressure warning valve
and transmitters must be installed to the wheels which will be
installed to the vehicle.
When new tire pressure warning valve and transmitters are
installed, new ID codes must be registered in the tire pressure
warning computer and the tire pressure warning system must be
initialized. (
◆
Initializing the tire pressure warning system
■
The tire pressure warning system must be initialized in the fol-
lowing circumstances:
●
When the tire inflation pressure is changed such as when chang-
ing traveling speed or load weight.
●
When the tire inflation pressure is changed such as when the tire
size is changed.
●
When rotating the tires.
●
Vehicles with a tire inflation pressure display function: After per-
forming the transmitter ID code registration procedure. (
When the tire pressure warning system is initialized, the current tire
inflation pressure is set as the benchmark pressure.
■
How to initialize the tire pressure warning system
Park the vehicle in a safe place and stop the hybrid system for 20
minutes or more.
The initialization procedure cannot be started while the vehicle is
moving.
Adjust the tire inflation pressure to the specified cold tire inflation
pressure level. (
Make sure to adjust the tire pressure to the specified cold tire infla-
tion pressure level. The tire pressure warning system will operate
based on this pressure level.
Start the hybrid system. (
Select
(4.2-inch display) or
(7-inch display) on the multi-
information display using the meter control switches on the steer-
ing wheel. (
4.2-inch display: Select “Vehicle Settings” and then press
.
7-inch display: Select
and then press and hold
.
Select “TPWS” and then press
.
1
2
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
425
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Select “Set Pressure” then
press and hold
until
the tire pressure warning
light blinks 3 times.
Then a message will be dis-
played on the multi-information
display.
Vehicles with a tire inflation
pressure display function: “- -”
will be displayed on the multi-
information display for the
inflation pressure of each tire
while initialization is being per-
formed.
Vehicles with a tire inflation pressure display function: Drive at
approximately 25 mph (40 km/h) or more for approximately 10 to
30 minutes.
When initialization is complete, the inflation pressure of each tire will
be displayed on the multi-information display.
Even if the vehicle is not driven at approximately 25 mph (40 km/h)
or more, initialization can be completed by driving for a long time.
However, if initialization does not complete after driving for 1 hour or
more, park the vehicle in a safe place for approximately 20 minutes
and then drive the vehicle again.
7
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
426
6-3. Do-it-yourself maintenance
◆
Registering ID codes
Vehicles without a tire inflation pressure display function
Every tire pressure warning valve and transmitter has a unique ID
code. In addition to the set of tire pressure warning system sensor
ID codes initially registered to the vehicle, a second set of ID codes
can be registered.
A second set of tire pressure warning system sensor ID codes can
be registered at your Toyota dealer. When 2 sets of ID codes have
been registered, either ID code set can be selected.
Vehicles with a tire inflation pressure display function
Every tire pressure warning valve and transmitter has a unique ID
code. When replacing a tire pressure warning valve and transmitter,
it is necessary to register the ID codes.
The ID codes can be registered on
(4.2-inch display) or
(7-
inch display) of the multi-information display.
■
Changing the available set of ID codes (vehicles without a tire
inflation pressure display function)
When 2 sets of ID codes are registered, the corresponding ID code
set for the installed wheels can be selected on
(4.2-inch display)
or
(7-inch display) of the multi-information display. It is not nec-
essary to reregister the ID codes each time the wheels are
changed.
For information regarding changing the registered ID codes for an
ID code set, contact your Toyota dealer.
■
How to register the ID codes (vehicles with a tire inflation pres-
sure display function)
Park the vehicle in a safe place, wait for approximately 20 min-
utes, and then start the hybrid system. (
Select
(4.2-inch display) or
(7-inch display) on the multi-
information display using the meter control switches on the steer-
ing wheel. (
4.2-inch display: Select “Vehicle Settings” and then press
.
7-inch display: Select
and then press and hold
.
Select “TPWS” and then press
.
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
427
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Select “Change Wheel” then
press and hold
until
the tire pressure warning
light blinks slowly 3 times.
Then a message will be dis-
played on the multi-information
display.
When registration is being per-
formed, the tire pressure warn-
ing
light
will
blink
for
approximately 1 minute then
illuminate and “- -” will be dis-
played for the inflation pres-
sure of each tire on the multi-
information display.
Drive at approximately 25 mph (40 km/h) or more for approxi-
mately 10 to 30 minutes.
Registration is complete when the tire pressure warning light turns
off and the inflation pressure of each tire is displayed on the multi-
information display.
Even if the vehicle is not driven at approximately 25 mph (40 km/h)
or more, registration can be completed by driving for a long time.
However, if registration does not complete after driving for 1 hour or
more, perform the procedure again from the beginning.
Initialize the tire pressure warning system. (
5
6
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
428
6-3. Do-it-yourself maintenance
■
When to replace your vehicle’s tires
Tires should be replaced if:
●
The treadwear indicators are showing on a tire.
●
You have tire damage such as cuts, splits, cracks deep enough to
expose the fabric, and bulges indicating internal damage
●
A tire goes flat repeatedly or cannot be properly repaired due to the size
or location of a cut or other damage
If you are not sure, consult with your Toyota dealer.
■
Replacing tires and wheels
If the ID codes of the tire pressure warning valve and transmitters are not
registered, the tire pressure warning system will not work properly. In this
case, after driving for about 20 minutes, the tire pressure warning light will
blink for approximately 1 minute and then illuminate to indicate a system
malfunction.
■
Tire life
Any tire over 6 years old must be checked by a qualified technician even
if it has seldom or never been used or damage is not obvious.
■
Routine tire inflation pressure checks
The tire pressure warning system does not replace routine tire inflation
pressure checks. Make sure to check tire inflation pressure as part of
your routine of daily vehicle checks.
■
Low profile tires (vehicles with 18-inch wheels)
Generally, low profile tires will wear more rapidly and tire grip perfor-
mance will be reduced on snowy and/or icy roads when compared to
standard tires. Be sure to use snow tires on snowy and/or icy roads and
drive carefully at a speed appropriate for road and weather conditions.
■
Maximum load of tire
Check that the maximum load of the replacement tire is greater than 1/2
of the Gross Axle Weight Ratings (GAWR) of either the front axle or the
rear axle, whichever is greater.
For the GAWR, see the Certification
Label. For the maximum load of the tire,
see the load limit at maximum cold tire
inflation pressure mentioned on the
sidewall of the tire. (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
429
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
Tire types
●
Summer tires
Summer tires are high-speed performance tires best suited to highway
driving under dry conditions. Since summer tires do not have the same
traction performance as snow tires, summer tires are inadequate for
driving on snow-covered or icy roads. For driving on snow-covered
roads or icy roads, the use of snow tires is recommended. When install-
ing snow tires, be sure to replace all four tires.
●
All season tires
All season tires are designed to provide better traction in snow and to
be adequate for driving in most winter conditions as well as for use
year-round. All season tires, however, do not have adequate traction
performance compared with snow tires in heavy or loose snow. Also, all
season tires fall short in acceleration and handling performance com-
pared with summer tires in highway driving.
●
Snow tires
For driving on snow-covered roads or icy roads, we recommend using
snow tires. If you need snow tires, select tires of the same size, con-
struction and load capacity as the originally installed tires. Since your
vehicle has radial tires as original equipment, make sure your snow
tires also have radial construction. Do not install studded tires without
first checking local regulations for possible restrictions. Snow tires
should be installed on all wheels. (
■
If the tread on snow tires wears down below 0.16 in. (4 mm)
The effectiveness of the tires as snow tires is lost.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
430
6-3. Do-it-yourself maintenance
■
Situations in which the tire pressure warning system may not oper-
ate properly
●
In the following situations, the tire pressure warning system may not
operate properly.
• If non-genuine Toyota wheels are used.
• If a tire has been replaced with a tire that is not an OE (Original
Equipment) tire.
• If a tire has been replaced with a tire that is not of the specified size.
• If tire chains, etc. are installed.
• If a window tint that affects radio wave signals is installed.
• If there is a lot of snow or ice on the vehicle, particularly around the
wheels or wheel housings.
• If the tire inflation pressure is much higher than the specified level.
• If wheels not equipped with tire pressure warning valve and transmit-
ter are used.
• If the ID codes of the tire pressure warning valve and transmitters are
not registered in the tire pressure warning computer.
●
Performance may be affected in the following situations.
• When driving near a TV tower, electric power plant, gas station, radio
station, large display, airport or other facility that generates strong
radio waves or electrical noise
• When carrying a portable radio, cellular phone, cordless phone or
other wireless communication device
Vehicles with a tire inflation pressure display function: If tire position
information is not correctly displayed due to the radio wave conditions,
the display may be corrected by changing the location of the vehicle as
the radio wave conditions may change.
●
When the vehicle is stopped, the time taken for the warning to start or
turn off may be longer.
●
When the inflation pressure of a tire drops rapidly, for example when a
tire has burst, the warning may not operate.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
431
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
Initialization procedure
●
Make sure to perform the initialization procedure after adjusting the tire
inflation pressure.
Also, make sure the tires are cold before performing the initialization
procedure or adjusting the tire inflation pressure.
●
If the power switch is turned off during initialization, it is not necessary to
restart the initialization procedure from the beginning as it will begin
automatically when the power switch is turned back to ON mode.
●
If initialization has accidentally been started when it is not necessary,
adjust the tire inflation pressure to the specified level when the tires are
cold and then perform the initialization procedure again.
●
Vehicles with a tire inflation pressure display function: While the position
of each tire is being determined and the inflation pressures are not being
displayed on the multi-information display, if the inflation pressure of a
tire drops, the tire pressure warning light will come on.
■
Warning performance of the tire pressure warning system
The warning of the tire pressure warning system will change in accor-
dance with the conditions under which it was initialized. For this reason,
the system may give a warning even if the tire pressure does not reach a
low enough level, or if the pressure is higher than the pressure that was
adjusted to when the system was initialized.
■
If the tire pressure warning system is not initialized properly
Vehicles without a tire inflation pressure display function
Initialization can be completed in a few minutes. However, in the following
cases, the settings have not been recorded and the system will not oper-
ate properly. If repeated attempts to record tire inflation pressure settings
are unsuccessful, have the vehicle inspected by your Toyota dealer.
●
If initialization is attempted and the tire pressure warning light does not
blink 3 times.
●
If, when the vehicle has been driven for about 20 minutes after perform-
ing initialization, the tire pressure warning light blinks for approximately
1 minute and then illuminates.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
432
6-3. Do-it-yourself maintenance
Vehicles with a tire inflation pressure display function
●
In the following situations, initialization may take longer than usual to be
completed or may not be possible. (Usually, the vehicle will need to be
driven for approximately 10 to 30 minutes to complete initialization.)
If initialization is not complete after driving approximately 30 minutes,
continue driving for a while.
• If the vehicle is driven on an unpaved road, it may take longer to com-
plete initialization.
• If the vehicle is backed up while performing initialization, data col-
lected during initialization will be cleared and it will take longer than
normal to complete.
• If the vehicle is driven in heavy traffic or another situation where other
vehicles are driven close by, it may take time for the system to recog-
nize the tire pressure warning valve and transmitters of your vehicle
over those of other vehicles.
If initialization is not complete after driving for approximately 1 hour,
park the vehicle in a safe place for approximately 20 minutes and then
drive the vehicle again.
●
In the following situations, initialization will not be started or was not
completed properly and the system will not operate properly. Perform
the initialization procedure again.
• If, when attempting to start initialization, the tire pressure warning light
does not blink 3 times.
• If, when the vehicle has been driven for about 20 minutes after per-
forming initialization, the tire pressure warning light blinks for approxi-
mately 1 minute and then illuminates.
●
If initialization cannot be completed after performing the above proce-
dure, contact your Toyota dealer.
■
When registering ID codes (vehicles with a tire inflation pressure dis-
play function)
●
Before performing ID code registration, make sure that no wheels with
tire pressure warning valve and transmitters installed are near the vehi-
cle.
●
Make sure to initialize the tire pressure warning system after registering
the ID codes. If the system is initialized before registering the ID codes,
the initialized values will be invalid.
●
As the tires will be warm when registration is completed, make sure to
allow the tires to cool before performing initialization.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
433
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
Canceling ID code registration (vehicles with a tire inflation pressure
display function)
●
To cancel ID code registration after it has been started, turn the power
switch off before driving the vehicle.
If the vehicle is driven after ID code registration is started, to cancel reg-
istration, perform the ID code registration start procedure again and turn
the power switch off before driving.
●
If ID code registration has been canceled, the tire pressure warning light
will blink for approximately 1 minute when the power switch is turned to
ON mode and then illuminate. The tire pressure warning system will be
operational when the tire pressure warning light turns off.
●
If the warning light does not turn off even after several minutes have
elapsed, ID code registration may not have been cancelled correctly. To
cancel registration, perform the ID code registration start procedure
again and then turn the power switch off before driving.
■
If ID codes are not registered properly (vehicles with a tire inflation
pressure display function)
●
In the following situations, ID code registration may take longer than
usual to be completed or may not be possible. (Usually, the vehicle will
need to be driven for approximately 10 to 30 minutes to complete ID
code registration.)
If ID code registration is not complete after driving for approximately 30
minutes, continue driving for a while.
• If the vehicle is driven on an unpaved road, it may take longer than
normal to complete registration.
• If the vehicle is backed up while performing registration, data col-
lected during registration will be cleared, and it will take longer than
normal to complete.
• If the vehicle is driven in heavy traffic or another situation where other
vehicles are driven close by, it may take time for the system to recog-
nize the tire pressure warning valve and transmitters of your vehicle
over those of other vehicles.
• If a wheel with a tire pressure warning valve and transmitter installed
is inside or near the vehicle, registration of the ID codes for the
installed wheels may not be possible.
If ID registration is not complete after driving for approximately 1 hour,
park the vehicle in a safe place for approximately 20 minutes and then
perform the ID code registration procedure again.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
434
6-3. Do-it-yourself maintenance
●
In the following situations, ID code registration will not be started or was
not completed properly and the system will not operate properly. Per-
form the ID code registration procedure again.
• If, when attempting to start ID code registration, the tire pressure
warning light does not blink slowly 3 times.
• If, when the vehicle has been driven for about 20 minutes after per-
forming ID code registration, the tire pressure warning light blinks for
approximately 1 minute and then illuminates.
●
If ID code registration cannot be completed after performing the above
procedure, contact your Toyota dealer.
■
Tire pressure warning system certification
For vehicles sold in the U.S.A.
For vehicles sold in Canada
Model: PMV-E000
-------------------------------------------------------------------------------------------------------------------------------------------------------------
435
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
WARNING
■
When inspecting or replacing tires
Observe the following precautions to prevent accidents.
Failure to do so may cause damage to parts of the drive train as well as
dangerous handling characteristics, which may lead to an accident
resulting in death or serious injury.
●
Do not mix tires of different makes, models or tread patterns.
Also, do not mix tires of remarkably different treadwear.
●
Do not use tire sizes other than those recommended by Toyota.
●
Do not mix differently constructed tires (radial, bias-belted or bias-ply
tires).
●
Do not mix summer, all season and snow tires.
●
Do not use tires that have been used on another vehicle.
Do not use tires if you do not know how they were used previously.
■
When initializing the tire pressure warning system
Do not initialize the tire pressure warning system without first adjusting
the tire inflation pressure to the specified level. Otherwise, the tire pres-
sure warning light may not come on even if the tire inflation pressure is
low, or it may come on when the tire inflation pressure is actually nor-
mal.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
436
6-3. Do-it-yourself maintenance
NOTICE
■
Repairing or replacing tires, wheels, tire pressure warning valve
and transmitters and tire valve caps
●
When removing or fitting the wheels, tires or the tire pressure warning
valve and transmitters, contact your Toyota dealer as the tire pressure
warning valve and transmitters may be damaged if not handled cor-
rectly.
●
Make sure to install the tire valve caps. If the tire valve caps are not
installed, water may enter the valves of the tire pressure warning valve
and transmitters and the valves may become stuck.
●
When replacing tire valve caps, do not replace them with metal caps or
any tire valve caps other than specified, as they may become stuck.
■
To avoid damage to the tire pressure warning valve and transmit-
ters
When a tire is repaired with liquid sealants, the tire pressure warning
valve and transmitter may not operate properly. If a liquid sealant is
used, contact your Toyota dealer or other qualified service shop as soon
as possible. Make sure to replace the tire pressure warning valve and
transmitter when replacing the tire. (
■
Driving on rough roads
Take particular care when driving on roads with loose surfaces or pot-
holes.
These conditions may cause losses in tire inflation pressure, reducing
the cushioning ability of the tires. In addition, driving on rough roads
may cause damage to the tires themselves, as well as the vehicle’s
wheels and body.
■
Low profile tires (vehicles with 18-inch wheels)
Low profile tires may cause greater damage than usual to the tire wheel
when sustaining impact from the road surface. Therefore, pay attention
to the following:
●
Be sure to use proper tire inflation pressure. If tires are under-inflated,
they may be damaged more severely.
●
Avoid potholes, uneven pavement, curbs and other road hazards. Fail-
ure to do so may lead to severe tire and wheel damage.
■
If tire inflation pressure of each tire becomes low while driving
Do not continue driving, or your tires and/or wheels may be ruined.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
437
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
The recommended cold tire infla-
tion pressure and tire size are dis-
played on the tire and loading
information label. (
Tire inflation pressure
Tire inflation pressure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
438
6-3. Do-it-yourself maintenance
Tire valve
Tire pressure gauge
Remove the tire valve cap.
Press the tip of the tire pressure gauge onto the tire valve.
Read the pressure using the gauge gradations.
If the tire inflation pressure is not at the recommended level, adjust
the pressure.
If you add too much air, press the center of the valve to deflate.
After completing the tire inflation pressure measurement and
adjustment, apply soapy water to the valve and check for leakage.
Put the tire valve cap back on.
■
Tire inflation pressure check interval
You should check tire inflation pressure every two weeks, or at least once
a month.
Do not forget to check the spare.
■
Effects of incorrect tire inflation pressure
Driving with incorrect tire inflation pressure may result in the following:
●
Reduced fuel economy
●
Reduced driving comfort and poor handling
●
Reduced tire life due to wear
●
Reduced safety
●
Damage to the drivetrain
If a tire needs frequent inflating, have it checked by your Toyota dealer.
Inspection and adjustment procedure
1
2
1
2
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
439
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
Instructions for checking tire inflation pressure
When checking tire inflation pressure, observe the following:
●
Check only when the tires are cold.
If your vehicle has been parked for at least 3 hours or has not been
driven for more than 1 mile or 1.5 km, you will get an accurate cold tire
inflation pressure reading.
●
Always use a tire pressure gauge.
It is difficult to judge if a tire is properly inflated based only on its appear-
ance.
●
It is normal for the tire inflation pressure to be higher after driving as
heat is generated in the tire. Do not reduce tire inflation pressure after
driving.
●
Never exceed the vehicle capacity weight.
Passengers and luggage weight should be placed so that the vehicle is
balanced.
WARNING
■
Proper inflation is critical to save tire performance
Keep your tires properly inflated.
If the tires are not properly inflated, the following conditions may occur
which could lead to an accident resulting in death or serious injury:
●
Excessive wear
●
Uneven wear
●
Poor handling
●
Possibility of blowouts resulting from overheated tires
●
Air leaking from between tire and wheel
●
Wheel deformation and/or tire damage
●
Greater possibility of tire damage while driving (due to road hazards,
expansion joints, sharp edges on the road, etc.)
NOTICE
■
When inspecting and adjusting tire inflation pressure
Be sure to put the tire valve caps back on.
If a valve cap is not installed, dirt or moisture may get into the valve and
cause an air leak, resulting in decreased tire inflation pressure.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
440
6-3. Do-it-yourself maintenance
When replacing wheels, care should be taken to ensure that they are
equivalent to those removed in load capacity, diameter, rim width and
inset
*
.
Replacement wheels are available at your Toyota dealer.
*
: Conventionally referred to as “offset”.
Toyota does not recommend using the following:
●
Wheels of different sizes or types
●
Used wheels
●
Bent wheels that have been straightened
●
Use only Toyota wheel nuts and wrenches designed for use with
your aluminum wheels.
●
When rotating, repairing or changing your tires, check that the
wheel nuts are still tight after driving 1000 miles (1600 km).
●
Be careful not to damage the aluminum wheels when using tire
chains.
●
Use only Toyota genuine balance weights or equivalent and a plas-
tic or rubber hammer when balancing your wheels.
■
When replacing wheels
The wheels of your vehicle are equipped with tire pressure warning valve
and transmitters that allow the tire pressure warning system to provide
advance warning in the event of a loss in tire inflation pressure. When-
ever wheels are replaced, tire pressure warning valve and transmitters
must be installed. (
Wheels
If a wheel is bent, cracked or heavily corroded, it should be
replaced. Otherwise, the tire may separate from the wheel or
cause a loss of handling control.
Wheel selection
Aluminum wheel precautions (if equipped)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
441
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
WARNING
■
When replacing wheels
●
Do not use wheels that are a different size from those recommended in
the Owner’s Manual, as this may result in a loss of handling control.
●
Never use an inner tube in a leaking wheel which is designed for a
tubeless tire. Doing so may result in an accident, causing death or seri-
ous injury.
■
When installing the wheel nuts
●
Never use oil or grease on the wheel bolts or wheel nuts.
Oil and grease may cause the wheel nuts to be excessively tightened,
leading to bolt or disc wheel damage. In addition, the oil or grease can
cause the wheel nuts to loosen and the wheel may fall off, causing an
accident and resulting in death or serious injury. Remove any oil or
grease from the wheel bolts or wheel nuts.
NOTICE
■
Replacing tire pressure warning valve and transmitters
●
Because tire repair or replacement may affect the tire pressure warn-
ing valve and transmitters, make sure to have tires serviced by your
Toyota dealer or other qualified service shop. In addition, make sure to
purchase your tire pressure warning valve and transmitters at your
Toyota dealer.
●
Ensure that only genuine Toyota wheels are used on your vehicle.
Tire pressure warning valve and transmitters may not work properly
with non-genuine wheels.
●
Be sure to install the wheel nuts with
the tapered ends facing inward.
Installing the nuts with the tapered
ends facing outward can cause the
wheel to break and eventually cause
the wheel to come off while driving,
which could lead to an accident
resulting in death or serious injury.
Tapered
portion
-------------------------------------------------------------------------------------------------------------------------------------------------------------
442
6-3. Do-it-yourself maintenance
Turn the power switch off.
Open the glove box and
remove the glove box cover
inside the glove box.
Remove the filter cover.
Unlock the filter cover.
Move the filter cover in the
direction of the arrow, and
then pull it out of the claws.
Remove the filter case.
There may be foreign objects on
top of the air conditioning filter.
Air conditioning filter
The air conditioning filter must be changed regularly to maintain
air conditioning efficiency.
Removal method
1
2
3
1
2
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
443
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Remove the air conditioning fil-
ter from the filter case and
replace it with a new one.
The “
UP” marks shown on the fil-
ter and the filter case should be
pointing up.
■
Checking interval
Inspect and replace the air conditioning filter according to the maintenance
schedule. In dusty areas or areas with heavy traffic flow, early replacement
may be required. (For scheduled maintenance information, please refer to the
“Schedule maintenance guide” or “Owner’s Manual Supplement”.)
■
If air flow from the vents decreases dramatically
The filter may be clogged. Check the filter and replace if necessary.
■
Air conditioning filter with deodorizing function
When fragrances are placed in your vehicle, the deodorizing effect may
become significantly weakened in a short period.
When an air conditioning odor comes out continuously, replace the air condi-
tioning filter.
5
NOTICE
■
When using the air conditioning system
Make sure that a filter is always installed.
Using the air conditioning system without a filter may cause damage to the
system.
■
To prevent damage to the filter cover
When moving the filter cover in the direc-
tion of arrow to release the fitting, pay
attention not to apply excessive force to
the claws. Otherwise, the claws may be
damaged.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
444
6-3. Do-it-yourself maintenance
Remove the dust from the air
intake vent with a vacuum
cleaner, etc.
Make sure to only use a vacuum to
suck out dust and clogs. Attempt-
ing to blow out dust and clogs
using an airgun, etc. may push it
into the air intake vent. (
If dust and clogs cannot be completely removed with the air intake
vent cover installed, remove the cover and clean the filter.
Turn the power switch off.
Using a Phillips screwdriver,
remove the clip.
Cleaning the hybrid battery (traction bat-
tery) air intake vent and filter
To prevent the fuel economy from being affected, visually
inspect the hybrid battery (traction battery) air intake vent peri-
odically for dust and clogs. If it is dusty or clogged or if “Mainte-
nance Required for Traction Battery Cooling Parts See Owner’s
Manual” is displayed on the multi-information display, clean the
air intake vent using the following procedures:
Cleaning the air intake vent
If dust and clogs cannot be completely removed
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
445
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Remove the air intake vent
cover.
Pull the cover as shown in
the illustration to disengage
the 7 claws, starting from the
claw in the upper right cor-
ner.
Pull the cover toward the
front of the vehicle to remove
it.
Remove the air intake vent fil-
ter.
Disengage the 3 claws as
shown in the illustration.
Remove the filter from the
cover.
Remove the dust and clogs
from the filter using a vacuum
cleaner, etc.
Make sure to also remove the dust
and clogs from the inside of the air
intake vent cover.
3
1
2
4
1
2
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
446
6-3. Do-it-yourself maintenance
Reinstall the filter to the cover.
Engage the filter to the 2
claws as shown in the illus-
tration.
Engage the 3 claws to install
the filter.
Make sure that the filter is not
crooked or deformed when install-
ing it.
Install the air intake vent cover.
Insert the tab of the cover as
shown in the illustration.
Push the cover to engage the
7 claws.
Using a Phillips screwdriver,
install the clip.
6
1
2
7
1
2
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
447
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
Scheduled maintenance of the air intake vent is necessary when
In some situations such as when the vehicle is used frequently or in heavy
traffic or dusty areas, the air intake vent may need to be cleaned more regu-
larly. For details, refer to “Schedule maintenance guide” or “Owner’s Manual
Supplement”.
■
Cleaning the air intake vent
●
Dust in the air intake vent may interfere with the cooling of the hybrid battery
(traction battery). If charging/discharging of the hybrid battery (traction bat-
tery) becomes limited, the distance that the vehicle can be driven using the
electric motor (traction motor) may be reduced and the fuel economy may
be reduced.
Inspect and clean the air intake vent periodically.
●
Improper handling of the air intake vent cover and filter may result in dam-
age to them. If you have any concerns about cleaning the filter, contact your
Toyota dealer.
■
If “Maintenance Required for Traction Battery Cooling Parts See Owner’s
Manual” is displayed on the multi-information display
●
If this warning message is displayed on the multi-information display,
remove the air intake vent cover and clean the filter. (
●
After cleaning the air intake vent, start the hybrid system and check that the
warning message is no longer displayed.
After the hybrid system is started, it may be necessary to drive the vehicle
up to approximately 20 minutes before the warning message disappears. If
the warning message does not disappear after driving for appropriately 20
minutes, have the vehicle inspected by your Toyota dealer.
WARNING
■
When cleaning the air intake vent
●
Do not use water or other liquids to clean the air intake vent. If water is
applied to the hybrid battery (traction battery) or other components, a mal-
function or fire may occur.
●
Before cleaning the air intake vent, make sure to turn the power switch off
to stop the hybrid system.
■
When removing the air intake vent cover
Do not touch the service plug located near the air intake vent. (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
448
6-3. Do-it-yourself maintenance
NOTICE
■
When cleaning the air intake vent
■
To prevent damage to the vehicle
●
Do not allow water or foreign matter to enter the air intake vent when the
cover is removed.
●
Carefully handle the removed filter so that it will not be damaged.
If the filter is damaged, have it replaced with a new filter by your Toyota
dealer.
●
Make sure to reinstall the filter and cover to their original positions after
cleaning.
●
Do not install anything to the air intake vent other than the exclusive filter
for this vehicle or use the vehicle without the filter installed.
■
If “Maintenance Required for Traction Battery Cooling Parts See
Owner’s Manual” is displayed on the multi-information display
If the vehicle is continuously driven with the warning message (indicating
that charging/discharging of the hybrid battery (traction battery) may
become limited) displayed, the hybrid battery (traction battery) may mal-
function. If a warning message is displayed, clean the air intake vent imme-
diately.
When cleaning the air intake vent, make
sure to only use a vacuum to suck out
dust and clogs. If a compressed air blow
gun, etc. is used to blow out dust and
clogs, the dust or clogs may be pushed
into the air intake vent, which may affect
the performance of the hybrid battery
(traction battery) and cause a malfunc-
tion.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
449
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
●
Flathead screwdriver
●
Small flathead screwdriver
●
Lithium battery CR2032
Release the lock and remove
the mechanical key.
Remove the key cover.
To prevent damage to the key,
cover the tip of the flathead screw-
driver with a rag.
Remove the depleted battery
using a small flathead screw-
driver.
When removing the cover, the
electronic key module may stick to
the cover and the battery may not
be visible. In this case, remove the
electronic key module in order to
remove the battery.
Insert a new battery with the “+” terminal facing up.
Electronic key battery
Replace the battery with a new one if it is depleted.
You will need the following items:
Replacing the battery
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
450
6-3. Do-it-yourself maintenance
When installing the key cover and mechanical key, install by con-
ducting
and
with the directions reversed.
Operate the
or
switch and check that the doors can
be locked/unlocked.
■
When replacing the key battery
Be careful not to lose the battery or any other small parts.
■
Use a CR2032 lithium battery
●
Batteries can be purchased at your Toyota dealer, local electrical appliance
shops or camera stores.
●
Replace only with the same or equivalent type recommended by the manu-
facturer.
●
Dispose of used batteries according to local laws.
■
If the key battery is depleted
The following symptoms may occur:
●
The smart key system and wireless remote control will not function properly.
●
The operational range will be reduced.
WARNING
■
Removed battery and other parts
These parts are small and if swallowed by a child, they can cause choking.
Keep away from children. Failure to do so could result in death or serious
injury.
NOTICE
■
For normal operation after replacing the battery
Observe the following precautions to prevent accidents:
●
Always work with dry hands.
Moisture may cause the battery to rust.
●
Do not touch or move any other component inside the remote control.
●
Do not bend either of the battery terminals.
4
2
1
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
451
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Turn the power switch off.
Open the fuse box cover.
Checking and replacing fuses
If any of the electrical components do not operate, a fuse may
have blown. If this happens, check and replace the fuses as nec-
essary.
1
2
Engine compartment (type A)
Engine compartment (type B)
Push the tabs in and lift the lid off.
Push the tabs in and lift the lid
off.
Under the driver’s side instru-
ment panel
Remove the lid.
Make sure to push the claw when
removing/installing the lid.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
452
6-3. Do-it-yourself maintenance
Remove the fuse with the pull-
out tool.
Only type A fuses can be removed
using the pullout tool.
Check if the fuse is blown.
Normal fuse
Blown fuse
Replace the blown fuse with a new fuse of an appropriate amperage rat-
ing. The amperage rating can be found on the fuse box lid.
3
4
Type A
Type B
Type C
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
453
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
After a fuse is replaced
●
If the lights do not turn on even after the fuse has been replaced, a bulb may
need replacement. (
●
If the replaced fuse blows again, have the vehicle inspected by your Toyota
dealer.
■
If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
WARNING
■
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage to the vehicle, and possibly a fire or
injury.
●
Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
●
Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
●
Do not modify the fuses or fuse boxes.
NOTICE
■
Before replacing fuses
Have the cause of electrical overload determined and repaired by your
Toyota dealer as soon as possible.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
454
6-3. Do-it-yourself maintenance
Check the wattage of the light bulb to be replaced. (
Light bulbs
You may replace the following bulbs yourself. The difficulty level
of replacement varies depending on the bulb. If necessary bulb
replacement seems difficult to perform, contact your Toyota
dealer.
For more information about replacing other light bulbs, contact
your Toyota dealer.
Preparing for light bulb replacement
Bulb locations
Front
Rear
Front turn signal/parking lights
(bulb type)
Front side marker lights (bulb
type)
Back-up lights (bulb type)
Rear turn signal lights (bulb
type)
Rear side marker lights (bulb
type)
1
2
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
455
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
Front turn signal/parking lights (bulb type)
Turn the bulb base counter-
clockwise.
Remove the light bulb.
Install a new light bulb and
then install the bulb base to
the light unit by inserting it
and turning it clockwise.
Replacing light bulbs
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
456
6-3. Do-it-yourself maintenance
■
Front side marker lights (bulb type)
To ensure enough space to
perform work, turn the steer-
ing wheel to move the front
wheel away from the light
bulb to be replaced.
Turn the steering wheel to the
left when replacing the right side
light bulb, and turn the steering
wheel to the right when replac-
ing the left side light bulb.
Remove the fender liner
clips.
To protect the front bumper
from being damaged, apply
protective tape around the
clip as shown in the illustra-
tion.
Use masking tape, etc. Do not
use duct tape, as it may leave
residue or damage the paint
when removed.
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
457
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
Insert a small flathead screw-
driver between the front
bumper and fender liner at
the position marked with a
“
” and then separate the
front bumper from the fender
liner.
To separate the front bumper
from the fender liner, pry up the
fender liner while pulling the
front bumper outward as shown
in the illustration.
Pull back the fender liner and
turn the bulb base counter-
clockwise.
Remove the light bulb.
Install a new light bulb and
then install the bulb base to
the light unit by inserting it
and turning it clockwise.
4
5
6
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
458
6-3. Do-it-yourself maintenance
Return the fender liner to its
original position, and install
the clips.
Make sure that the fender liner
is correctly positioned on the
inner side of the front bumper.
To Install the fender liner to
the front bumper, engage the
clip to the front bumper.
Remove the protective tape.
8
9
10
-------------------------------------------------------------------------------------------------------------------------------------------------------------
459
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
Back-up lights (bulb type)
Open the trunk lid and
remove the clips.
Partly remove the trunk lid
cover.
Disconnect the connector
while depressing the lock
release. (When replacing
right side bulb only.)
Turn the bulb base counter-
clockwise.
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
460
6-3. Do-it-yourself maintenance
Remove the light bulb.
Install a new light bulb and
then install the bulb base to
the light unit by inserting it
and turning it clockwise.
Connect
the
connector.
(When replacing right side
bulb only.)
Reinstall the trunk lid cover
with the clips.
5
6
7
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
461
6-3. Do-it-yourself maintenance
6
Mai
ntenan
ce and care
■
Rear turn signal lights (bulb type) and rear side marker lights
(bulb type)
Open the trunk and apply
protective tape to the vehicle
body around the light unit.
Use masking tape, etc. Do not
use duct tape, as it may leave
residue or damage the paint
when removed.
Remove the cover.
Insert a flathead screw-
driver between the cover
and the light unit and pry
up the cover in several
positions as shown in the
illustration to disengage
the claws (indicated by a
dotted line).
Pull the cover toward the
rear of the vehicle to dis-
engage the claws (indi-
cated by a dotted line) and
remove the cover.
To prevent scratching the vehi-
cle, wrap the tip of the flathead
screwdriver with a cloth, etc.
Remove the 2 bolts.
1
2
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст