Toyota Tundra. Manual — part 1400
DESCRIPTION
The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU
monitors the communications and WDC pulses from the sub CPU. When the signal malfunctions below are
detected, a DTC is output.
DTC DETECTION CONDITION AND TROUBLE AREA
MONITOR STRATEGY
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS
INSPECTION PROCEDURE
1. CHECK DTC
DTC Code
DTC Detection Condition
Trouble Area
P060A
When either condition below is met:
ECM main CPU error
ECM sub CPU error
Electronic throttle monitoring CPU error
ECM
Related DTCs
None
Required sensors/components (main)
ECM
Required sensors/components (sub)
-
Frequency of operation
Once per driving cycle
Duration
16 seconds
MIL operation
Immediate
Sequence of operation
None
CPU reset
Occurred
When either condition below is met:
Condition 1 or 2
1. When all conditions below are met:
-
CPU reset
1 time or more
Learned TP - Learned APP
0.4 V or higher
Electronic throttle actuator
OFF
2. CPU reset
2 times or more
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
a. Clear DTC. (See DTC CHECK/CLEAR ).
b. Turn the ignition switch off.
c. Disconnect the cable from the negative battery terminal and wait for 1 minute.
d. Connect the cable to the negative battery terminal.
e. Turn the ignition switch to ON.
f. Check DTC.
OK: P060A is not present.
NG : REPLACE ECM (See REMOVAL )
OK : CHECK FOR INTERMITTENT PROBLEMS (See CHECK FOR INTERMITTENT
PROBLEMS )
DTC P060B INTERNAL CONTROL MODULE A/D PROCESSING PERFORMANCE
DESCRIPTION
This DTC is output when a communication error occurs in the ECM.
DTC DETECTION CONDITION AND TROUBLE AREA
MONITOR STRATEGY
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS
DTC Code
DTC Detection Condition
Trouble Area
P060B
ECM main CPU communication error
ECM
Related DTCs
None
Required sensors/components (main)
ECM
Required sensors/components (sub)
-
Frequency of operation
Once per driving cycle
Duration
1 second
MIL operation
Immediate
Sequence of operation
None
None
-
Internal control module serial communication
Fail
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
INSPECTION PROCEDURE
1. CHECK DTC
a. Clear DTC. (See DTC CHECK/CLEAR ).
b. Turn the ignition switch off.
c. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
d. Connect the cable to the negative (-) battery terminal.
e. Turn the ignition switch to ON.
f. Check DTC.
OK: P060B is not present.
NG : REPLACE ECM (See REMOVAL )
OK : CHECK FOR INTERMITTENT PROBLEMS (See CHECK FOR INTERMITTENT
PROBLEMS )
DTC P060D INTERNAL CONTROL MODULE ACCELERATOR PEDAL POSITION
PERFORMANCE
DESCRIPTION
The ECM monitors the input signals of the Accelerator Pedal Position (APP) sensor No. 1. When the input
signals and control signals are deviated, a DTC is output.
DTC DETECTION CONDITION AND TROUBLE AREA
MONITOR STRATEGY
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
DTC Code
DTC Detection Condition
Trouble Area
P060D
When either condition below is met:
ECM main CPU error
ECM sub CPU error
ECM
Related DTCs
None
Required sensors/components (main)
ECM
Required sensors/components (sub)
-
Frequency of operation
Once per driving cycle
Duration
1 second
MIL operation
Immediate
Sequence of operation
None
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS
INSPECTION PROCEDURE
1. CHECK DTC
a. Clear DTC. (See DTC CHECK/CLEAR ).
b. Turn the ignition switch off.
c. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
d. Connect the cable to the negative (-) battery terminal.
e. Turn the ignition switch to ON.
f. Check DTC.
OK: P060D is not present.
NG : REPLACE ECM (See REMOVAL )
OK : CHECK FOR INTERMITTENT PROBLEMS (See CHECK FOR INTERMITTENT
PROBLEMS )
DTC P060E INTERNAL CONTROL MODULE THROTTLE POSITION PERFORMANCE
DESCRIPTION
The ECM monitors the input signals of the Throttle Position (TP) sensor No. 1 and stop light switch. As the
ECM monitors the input signals of the TP sensor No. 1 and the STP signals of the stop light switch, if the input
signals and control signals are deviated, a DTC is output.
DTC DETECTION CONDITION AND TROUBLE AREA
MONITOR STRATEGY
MONITOR STRATEGY
None
-
Difference of main APP and sub APP
0.3 V or higher
DTC Code
DTC Detection Condition
Trouble Area
P060E
When either condition below is met:
ECM main CPU error
ECM sub CPU error
ECM
Related DTCs
None
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст