Toyota Tundra. Manual — part 1399
The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning
properly. If outputs from the CPUs are different and deviate from the standard, the ECM will illuminate the
MIL and set a DTC immediately.
DTC DETECTION CONDITION AND TROUBLE AREA
MONITOR STRATEGY
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS
INSPECTION PROCEDURE
1. CHECK DTC
a. Clear DTC. (See DTC CHECK/CLEAR ).
b. Turn the ignition switch off.
c. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
d. Connect the cable to the negative (-) battery terminal.
e. Turn the ignition switch to ON.
f. Check DTC.
OK: P0606 is not present.
DTC Code
DTC Detection Condition
Trouble Area
P0606
When either condition below is met:
ECM main CPU error
ECM sub CPU error
ECM
Related DTC
P0606: ECM range check
Required sensors/Components (main)
ECM
Required sensors/Components (sub)
-
Frequency of Operation
Continuous
Duration
16 seconds
MIL Operation
Immediate
Sequence of Operation
None
Monitor runs whenever the following DTCs are not present
None
CPU reset
Occurred
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
NG : REPLACE ECM (See REMOVAL )
OK : CHECK FOR INTERMITTENT PROBLEMS (See CHECK FOR INTERMITTENT
PROBLEMS )
DTC P0607 CONTROL MODULE PERFORMANCE
DESCRIPTION
The ECM continuously monitors its internal processors (CPUs), A/F sensor transistors and heated oxygen
sensor (HO2S) transistors. This self-check ensures that the ECM is functioning properly. This is diagnosed by
internal "mirroring" of the main and sub CPUs to detect processor errors. If outputs from the processors deviate
from the standard, the ECM will illuminate the MIL and set a DTC immediately.
DTC DETECTION CONDITION AND TROUBLE AREA
MONITOR STRATEGY
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS
DTC Code
DTC Detection Condition
Trouble Area
P0607
When one of following conditions is met:
ECM CPUs malfunction
A/F sensor transistors malfunction
HO2S transistors malfunction
Exhaust gas leak
HO2S
ECM
NOTE:
An exhaust gas leak generates noise in the HO2S output. The ECM may
interpret this as an HO2S transistor malfunction and set P0607.
Related DTCs
None
Required sensors/Components (main)
ECM
Required sensors/Components (sub)
A/F sensor, HO2S
Frequency of operation
Continuous
Duration
60 seconds
MIL operation
Immediate
Sequence of operation
None
Estimated A/F sensor temperature
450 to 800°C (842 to 1472°F)
Estimated HO2S temperature
450 to 800°C (842 to 1472°F)
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
INSPECTION PROCEDURE
1. CHECK FOR EXHAUST GAS LEAK
a. Allow the engine to idle.
b. Check for exhaust gas leak around the HO2S.
OK: No leak from the HO2S.
NG : REPAIR LEAK
OK : Go to Next Step
2. CHECK HEATED OXYGEN SENSOR
Fig. 188: Fuel Trim Rear HO2S Voltage Graph
a. Warm up the engine.
b. Allow the engine to idle.
c. Enter the following menus: Powertrain/Engine and ECT Active Test/Control the Injection Volume
for A/F Sensor.
d. Check the O2S B1S2 (O2S B2S2) values when the Control the Injection Volume for A/F Sensor is
-12.5% (Lean fuel-trim).
e. Check the O2S B1S2 (O2S B2S2) values when the Control the Injection Volume for A/F Sensor is
25% (Rich fuel-trim).
Standard
A/F sensor transistors
Fail
HO2S transistors
Fail
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
FUEL-TRIM REFERENCE
NG : REPLACE HEATED OXYGEN SENSOR (See REMOVAL )
OK : Go to Next Step
3. CHECK DTC
a. Clear DTC. (See DTC CHECK/CLEAR ).
b. Turn the ignition switch off.
c. Disconnect the cable from the negative battery terminal and wait for 1 minute.
d. Connect the cable to the negative battery terminal.
e. Start the engine.
Fig. 189: Engine Coolant Temperature Graph
f. Perform the drive pattern.
1. Warm up the engine.
2. Accelerate the vehicle until 80 km/h (50 mph) and stop the vehicle.
3. Drive the vehicle by 60 to 80 km/h (35 to 50 mph) for 5 minutes or more.
g. Check DTC.
OK: P0607 is not present.
NG : REPLACE ECM (See REMOVAL )
OK : CHECK FOR INTERMITTENT PROBLEMS (See CHECK FOR INTERMITTENT
PROBLEMS )
DTC P060A INTERNAL CONTROL MODULE MONITORING PROCESSOR PERFORMANCE
A/F CONTROL O2S B1S2 (O2S B2S2)
-12.5%
Less than 0.2 V
25%
More than 0.8 V
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст