Toyota Tundra. Manual — part 1804
a
Disconnect the power steering oil pressure switch connector
b
Remove the 2 bolts, and disconnect the vane pump
HINT:
Make sure to suspend the vane pump securely
Fig. 185: Locating Power Steering Oil Pressure Switch Connector And Vane Pump Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
36
REMOVE GENERATOR ASSEMBLY (See REMOVAL )
37
DISCONNECT COOLER COMPRESSOR
a
Remove the 2 nuts, 2 bolts and disconnect the cooler compressor
Fig. 186: Locating Cooler Compressor Nuts And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
38
DISCONNECT NO. 1 AND NO. 2 FUEL PIPE
NOTE:
Do not hit other parts with the pulley when separating the vane
pump.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Fig. 187: Locating Fuel Tube Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a
Disconnect the No 1 and No 2 fuel pipe
1
Remove the fuel pipe clamp from the fuel tube connector
HINT:
Check for dirt or mud on the pipe and around the connector before disconnection Clean if
necessary
Fig. 188: Identifying Fuel Pipe Clamp
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
Pinch the connector and disconnect the connector and pipe
HINT:
If the connector and the pipe are stuck together, pinch the connector, push and pull the pipe
to disconnect the pipe and pull it out
3
Check for dirt or mud on the seal surface of the disconnected pipe Clean if necessary
NOTE:
Do not use any tools.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Fig. 189: Pinching Connector And Disconnecting Connector And Pipe
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4
To protect the disconnected pipe and connector from damage and contamination, cover it
with a plastic bag
Fig. 190: Covering Connector With Plastic Bag
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
39
REMOVE BATTERY
40
REMOVE FRONT FENDER APRON SEAL LH
41
REMOVE FRONT FENDER APRON SEAL RH
42
REMOVE STARTER ASSEMBLY
a
Remove the starter (for 1 6 kW Type) (see REMOVAL )
b
Remove the starter (for 2 0 kW Type) (see REMOVAL )
43
REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
a
Remove the flywheel housing side cover
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Fig. 191: Locating Flywheel Housing Side Cover
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Turn the crankshaft to gain access to the 6 bolts and remove the 6 bolts while holding the
crankshaft pulley set bolt with a wrench
Fig. 192: Locating Crankshaft Pulley Set Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
44
REMOVE FLYWHEEL HOUSING UNDER COVER
a
Remove the flywheel housing under cover
Fig. 193: Identifying Flywheel Housing Under Cover
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
45
REMOVE PROPELLER SHAFT ASSEMBLY (for 2 Joint Type) (See PROPELLER SHAFT
SYSTEM )
46
REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 3 Joint Type) (See
PROPELLER SHAFT SYSTEM )
47
DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (See REMOVAL )
48
SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY (See REMOVAL )
49
REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
a
Remove the 4 bolts of the rear No 1 engine mounting insulator
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст