Toyota Tundra. Manual — part 1805
Fig. 194: Locating Rear No. 1 Engine Mounting Insulator Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Remove the 4 nuts, 4 washers, 4 bolts and No 3 frame crossmember
Fig. 195: Locating No. 3 Frame Crossmember Nuts, Washers And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
50
REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
a
Remove the 4 bolts and engine mounting insulator
Fig. 196: Locating Rear No. 1 Engine Mounting Insulator Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
51
DISCONNECT WIRE HARNESS AND CONNECTOR (See REMOVAL )
52
DISCONNECT NO. 1 WATER BY-PASS PIPE (See REMOVAL )
53
REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (See REMOVAL )
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
54
REMOVE ENGINE ASSEMBLY
a
Install the 2 engine hangers with the 4 bolts shown below
Part No.:
ITEM REFERENCE
Torque: 33 N*m (336 kgf*cm, 24 ft.*lbf)
Fig. 197: Locating Engine Hangers & Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Attach the engine sling device and hang the engine with the chain block
Fig. 198: Hanging Engine With Chain Block Using Engine Sling Device
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Remove the 2 nuts and 4 bolts from the front engine mounting insulator LH and RH
d
Lift the engine out of the vehicle carefully
Item
Part No.
No 1 engine hanger 12281-31060
No 2 engine hanger 12282-31040
Bolt
90119-08A87
NOTE:
Make sure the engine is clear of all wiring and hoses.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
e
Remove the front engine mounting insulator LH and RH
f
Place the engine onto a working bench
Fig. 199: Locating Front Engine Mounting Insulator Nuts & Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
55
REMOVE DRIVE PLATE AND RING GEAR
a
Using SST, hold the crankshaft
SST 09213-54015 (91651-60855), 09330-00021
Fig. 200: Holding Crankshaft Using SST
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Remove the 8 bolts, rear spacer, drive plate and front spacer
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Fig. 201: Locating Drive Plate And Ring Gear Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
56
INSTALL ENGINE STAND
a
Install the engine onto an engine stand with the bolts
57
REMOVE ENGINE HANGER
a
Remove the 4 bolts and 2 engine hangers
Fig. 202: Locating Engine Hangers & Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
1
INSTALL ENGINE HANGER
a
Install the 2 engine hangers with the 4 bolts shown below
Fig. 203: Locating Engine Hangers & Bolts
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст