Toyota Tundra. Manual — part 1973
d
Tighten the 10 bolts in the order shown in the illustration
Torque: 16 N*m (163 kgf*cm, 12 ft.*lbf)
Fig. 350: Identifying Camshaft Housing Bolts Tightening Order
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
22
INSTALL CAMSHAFT BEARING CAP LH
a
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps
b
Install the No 3 and No 4 camshafts to the camshaft housing
c
Confirm the marks and numbers on the camshaft bearing caps and place them in their proper
positions and directions
Fig. 351: Identifying Marks And Numbers On Camshaft Bearing Caps
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d
Temporarily install the 10 bolts in the order shown in the illustration
NOTE:
Thoroughly wipe clean any seal packing.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 352: Identifying Camshaft Bearing Cap Bolts Installing Order
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
23
INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH
a
Install the valve rocker arms as shown in the illustration
Fig. 353: Identifying Valve Rocker Arms Position
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Apply seal packing in a continuous line as shown in the illustration
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Standard seal diameter:
3.5 to 4.0 mm (0.138 to 0.157 in.)
NOTE:
Remove any oil from the contact surface.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
c
Install the camshaft housing, and install the 18 bolts in the order shown in the illustration
Torque: for bolt A
10 N*m (102 kgf*cm, 7 ft.*lbf)
for except bolt A
30 N*m (306 kgf*cm, 22 ft.*lbf)
Install the camshaft housing within 3 minutes and tighten the
bolts within 15 minutes after applying seal packing.
Fig. 354: Identifying Seal Packing Areas On Camshaft Housing
Sub-Assembly - LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NOTE:
Do not start the engine for at least 2 hours after the installation.
Make sure that the knock pin of the camshaft is positioned as
shown in the illustration before installing the camshaft housing.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
d
Tighten the 10 bolts in the order shown in the illustration
Torque: 16 N*m (163 kgf*cm, 12 ft.*lbf)
Fig. 356: Tightening Order Of Camshaft Housing Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
24
INSTALL CRANKSHAFT TIMING GEAR KEY
a
Install the timing gear key
HINT:
The other timing gear key will be installed at a later step
Fig. 355: Identifying Camshaft Housing Bolts Installing Order
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NOTE:
Thoroughly wipe clean any seal packing.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст