Toyota Tundra. Manual — part 1971
b
Install the oil pan with the 14 bolts and 2 nuts
Torque: for bolt A
10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B
35 N*m (357 kgf*cm, 26 ft.*lbf)
for nut
35 N*m (357 kgf*cm, 26 ft.*lbf)
Fig. 337: Locating Oil Pan Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
9
INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
Fig. 336: Identifying Seal Packing Areas On No. 1 Oil Pan Sub-
Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NOTE:
Do not start the engine for at least 2 hours after installing.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
a
Apply seal packing in a continuous line as shown in the illustration
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Standard seal diameter:
3.0 to 4.0 mm (0.118 to 0.156 in.)
b
Install the oil pan with the 14 bolts and 2 nuts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
Fig. 339: Locating Oil Pan With Bolts And Nuts
NOTE:
Remove any oil from the contact surface.
Install the oil pan within 3 minutes and tighten the bolts and
nuts within 15 minutes after applying seal packing.
Fig. 338: Identifying Seal Packing Areas On No. 2 Oil Pan Sub-
Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NOTE:
Do not start the engine for at least 2 hours after installing.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
10
INSTALL NO. 1 HEAT EXCHANGER COVER
a
Apply seal packing in a continuous line as shown in the illustration
Seal packing:
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
Standard seal diameter:
3.0 to 4.0 mm (0.118 to 0.157 in.)
b
Install the heat exchanger cover with the 12 bolts and 2 nuts
Torque: for bolt C
10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt C
21 N*m (214 kgf*cm, 16 ft.*lbf)
Standard Bolt
HEAT EXCHANGER COVER STANDARD BOLT REFERENCE CHART
NOTE:
Remove any oil from the contact surface.
Install the No. 1 heat exchanger cover within 3 minutes and
tighten the bolts and nuts within 15 minutes after applying seal
packing.
Fig. 340: Identifying Seal Packing Areas On No. 1 Heat
Exchanger Cover
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 341: Locating Heat Exchanger Cover With Bolts And Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
11
INSTALL VENTILATION PIPE GASKET
a
Using SST, evenly tap in a new ventilation pipe gasket until its surface is flush with the lip of the
ventilation pipe
SST 09950-60010 (09951 -00360), 09950-70010 (09951-07100)
12
INSTALL CYLINDER BLOCK WATER JACKET SPACER
Item
Length
Thread Diameter
Bolt A 20 mm (0 787 in ) 8 mm (0 315 in )
Bolt B 70 mm (2 76 In ) 8 mm (0 315 In )
Bolt C 16 mm (0 630 In ) 6 mm (0 236 In )
NOTE:
Do not start the engine for at least 2 hours after installing.
NOTE:
Do not tap the gasket at an angle.
Do not tap the gasket excessively.
Fig. 342: Tapping In Ventilation Pipe Gasket
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст