Toyota Tundra. Manual — part 2323
Torque: 23 N*m (235 kgf*cm, 17 ft.*lbf)
Fig. 97: Identifying Tightening Sequence Of Bolts And Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 98: Identifying Seal Packing Labeled Area
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
a
Install 5 new gaskets to the camshaft bearing caps (No 2, No 3)
NOTE:
After the installation, if the seal packing has seeped out at the areas
labeled A shown in the illustration, wipe it off.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
Fig. 99: Identifying Camshaft Bearing Caps Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the gasket to the cylinder head cover
c
Apply seal packing as shown in the illustration
Fig. 100: Identifying Area For Applying Seal Packing
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
d
Install the cylinder head cover washer with a new seal and the 14 bolts
NOTE:
Remove any oil from the contact surface.
NOTE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the
bolts within 15 minutes after applying seal packing.
Do not start the engine for at least 2 hours after the installation.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
Fig. 101: Identifying Cylinder Head Cover Washer With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Torque: for bolt A
21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A
12 N*m (122 kgf*cm, 9 ft.*lbf)
4
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
a
Install 5 new gaskets to the camshaft bearing caps (No 1,No 3)
Fig. 102: Identifying Camshaft Bearing Caps Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the gasket to the cylinder head cover
c
Apply seal packing as shown in the illustration
NOTE:
Remove any oil from the contact surface.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
Fig. 103: Identifying Area For Applying Seal Packing
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
d
Install the cylinder head cover washer with a new seal and the 14 bolts
Fig. 104: Identifying Cylinder Head Cover Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Torque: for bolt A
21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A
12 N*m (122 kgf*cm, 9 ft.*lbf)
e
Install the noise filter to the cylinder head cover with the bolt
Torque: 7.0 N*m (71 kgf*cm, 62 in.*lbf)
NOTE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the
bolts within 15 minutes after applying seal packing.
Do not start the engine for at least 2 hours after the installation.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст