Toyota Tundra. Manual — part 1993
a
Using needle-nose pliers, remove the oil seals
Fig. 36: Removing Valve Stem Oil Seal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4
REMOVE VALVE SPRING SEAT
a
Using compressed air and a magnetic finger, remove the valve spring seat by blowing air onto it
Fig. 37: Removing Valve Spring Seat
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5
REMOVE NO. 1 STRAIGHT SCREW PLUG
a
Using a 10 mm hexagon wrench, remove the 6 screw plugs and 6 gaskets
NOTE:
If water leaks from the No. 1 screw plug or the plug is corroded, replace it.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Fig. 38: Locating No. 1 Screw Plugs And Gaskets
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
6
REMOVE NO. 2 STRAIGHT SCREW PLUG
a
Using a 14 mm hexagon wrench, remove the 2 screw plugs and 2 gaskets
Fig. 39: Locating No. 2 Screw Plug And Gaskets
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
7
REMOVE STUD BOLT
INSPECTION
1
INSPECT CAMSHAFT OIL CLEARANCE
a
Clean the bearing caps, camshaft housing and camshaft journals
b
Place the camshafts on the camshaft housing
c
Lay a strip of Plastigage across each of the camshaft journals
NOTE:
If water leaks from the No. 2 screw plug or the plug is corroded,
replace it.
NOTE:
If the stud bolt is deformed or its threads are damaged, replace it.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Fig. 40: Laying Strip Of Plastigage Across Camshaft Journals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d
Install the camshaft bearing caps (see REASSEMBLY )
e
Install the camshaft housing (see REASSEMBLY )
f
Remove the camshaft bearing caps (see DISASSEMBLY )
g
Measure the Plastigage at its widest point
Standard oil clearance
STANDARD OIL CLEARANCE SPECIFICATIONS
Maximum oil clearance
MAXIMUM OIL CLEARANCE SPECIFICATIONS
NOTE:
Do not turn the camshaft.
NOTE:
Do not turn the camshaft.
Item
Specified Condition
No 1 journal 0 030 to 0 065 mm (0 00118 to 0 00256 in )
Other journals 0 025 to 0 062 mm (0 000984 to 0 00244 in )
Item
Specified Condition
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Fig. 41: Measuring Plastigage At Widest Point
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
If the oil clearance is greater than the maximum, replace the camshaft If necessary, replace the
camshaft housing
2
INSPECT CAMSHAFT THRUST CLEARANCE
a
Inspect the LH side camshafts
1
Install the LH side camshafts
2
Using a dial indicator, measure the thrust clearance while moving the camshaft back and
forth
Standard thrust clearance: 0.08 to 0.135 mm (0.00315 to 0.00531 in.)
Maximum thrust clearance: 0.15 mm (0.00591 in.)
If the thrust clearance is greater than the maximum, replace the camshaft housing If the
thrust surface is damaged, replace the camshaft
No 1 journal 0 10 mm (0 00394 in )
Other journals 0 09 mm (0 00354 In )
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст