Toyota Tundra. Manual — part 2383

Fig. 75: Identifying Ignition Switch Replacement Components For Torque Specificaitons - For Manual
Tilt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 76: Identifying Ignition Switch Replacement Components With Torque Specifications - For Manual
Tilt And Telescopic
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 77: Identifying Ignition Switch Replacement Components With Torque Specifications - For Power
Tilt And Power Telescopic
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra

Fig. 78: Identifying Ignition Switch Replacement Components With Torque Specifications - For Manual
Tilt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 79: Identifying Ignition Switch Replacement Components - For Manual Tilt And Telescopic
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 80: Identifying Ignition Switch Replacement Components - For Power Tilt And Power Telescopic
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

REMOVAL

1

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra

2

REMOVE STEERING COLUMN ASSEMBLY

a

for Manual Tilt:

Remove the steering column assembly (See REMOVAL )

b

for Manual Tilt and Telescopic:

Remove the steering column assembly (see REMOVAL )

c

for Power Tilt and Power Telescopic:

Remove the steering column assembly (see REMOVAL )

3

REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Manual
Tilt) (See DISASSEMBLY )

4

REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Manual
Tilt and Telescopic) (See DISASSEMBLY )

5

REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Power
Tilt and Power Telescopic) (See DISASSEMBLY )

6

REMOVE IGNITION SWITCH ASSEMBLY (See DISASSEMBLY )

INSPECTION

1

INSPECT IGNITION SWITCH ASSEMBLY

a

Measure the resistance according to the value(s) in the table below

Standard resistance

IGNITION SWITCH ASSEMBLY

NOTE:



Some systems need to be initialized after the cable is reconnected
(see INITIALIZATION ).



After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.

Tester Connection Switch Condition Specified Condition

All terminals

LOCK

10 kohms or higher

2 (ACC) - 4 (AM1)

ACC

Below 1 ohms

1 (IG1) - 4 (AM1)

ON

2 (ACC) - 4 (AM1)

S (AM2) - 6 (IG2)

1 (IG1) - 4 (AM1)

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra

If the result is not as specified, replace the ignition switch assembly

Fig. 81: Identifying Ignition Switch Assembly Connector Terminal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

INSTALLATION

1

INSTALL IGNITION SWITCH ASSEMBLY (See REASSEMBLY )

2

INSTALL UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Manual
Tilt) (See REASSEMBLY )

3

INSTALL UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Manual
Tilt and Telescopic) (See REASSEMBLY )

4

INSTALL UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Power
Tilt and Power Telescopic) (See REASSEMBLY )

5

INSTALL STEERING COLUMN ASSEMBLY

a

for Manual Tilt:

Install the steering column assembly (See INSTALLATION )

b

for Manual Tilt and Telescopic:

Install the steering column assembly (see INSTALLATION )

c

for Power Tilt and Power Telescopic:

Install the steering column assembly (see INSTALLATION )

3 (ST1) - 4 (AM1)

START

5 (AM2) - 6 (IG2)

5 (AM2) - 7 (ST2)

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra