Toyota Tundra. Manual — part 2381

Fig. 61: Locating Dipstick Guide With Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

d

Install the dipstick

7

INSTALL GENERATOR ASSEMBLY

a

Install the generator with the 2 bolts and 2 nuts

Torque: 43 N*m (439 kgf*cm, 32 ft.*lbf)

Fig. 62: Locating Generator Nuts And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b

Connect the generator connector

c

Connect the generator wire with the nut

Torque: 9.8 N*m (100 kgf*cm, 87 in.*lbf)

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra

Fig. 63: Locating Generator Connector Terminal Cap And Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

d

Install the terminal cap

e

Install the harness bracket to the generator with the bolt

Torque: 31 N*m (316 kgf*cm, 23 ft.*lbf)

Fig. 64: Locating Wire Harness Bracket Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

8

CONNECT VANE PUMP ASSEMBLY

HINT:

Before performing the following procedures, move the spacer until the vane pump can be installed

Fig. 65: Locating Vane Pump Assembly Spacer
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

a

Connect the vane pump to the timing chain cover with the 2 bolts

Torque: 28 N*m (286 kgf*cm, 21 ft.*lbf)

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra

Fig. 66: Locating Vane Pump Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b

Connect the 2 clamps and power steering oil pressure switch connector

Fig. 67: Locating Power Steering Oil Pressure Switch Connector Clamps
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

9

INSTALL FRONT FENDER APRON SEAL RH (See INSTALLATION )

10

INSTALL FAN AND GENERATOR V BELT (See )

11

INSTALL AIR CLEANER ASSEMBLY (See INSTALLATION )

12

INSTALL AIR CLEANER HOSE ASSEMBLY (See INSTALLATION )

13

INSTALL V-BANK COVER (See INSTALLATION )

14

INSTALL NO. 1 ENGINE UNDER COVER (See REPLACEMENT )

15

CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

STARTER RELAY

ON-VEHICLE INSPECTION

1

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTE:

Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra

2

REMOVE STARTER RELAY (ST)

a

Remove the engine room relay box cover

b

Remove the starter relay from the engine room relay block

3

INSPECT STARTER RELAY

a

Measure the resistance according to the value(s) in the table below

Standard resistance

STARTER RELAY (ST)

If the result is not as specified, replace the relay

Fig. 68: Inspecting Starter Relay
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

4

INSTALL STARTER RELAY

5

CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTE:



Some systems need to be initialized after the cable is reconnected
(see INITIALIZATION ).



After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.

Terminal

Connection

Condition

Specified

Condition

3-5

When battery voltage is not applied to terminals land
2

10 kohms or higher

When battery voltage is applied to terminals 1 and 2

Below 1 ohms

NOTE:

Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra