Toyota Tundra. Manual — part 557
HINT:
The radio has a noise prevention function to reduce noise when listening to the radio. If a loud
noise occurs, check whether the ground at the antenna mounting base and the noise prevention unit
are installed and wired correctly.
NOISE CONDITION CHART
HINT:
In the chart's left column, find the situation that matches the customer's vehicle. Then, in the
right column, find the part that is causing the noise. Check the noise filter on the part.
To save time and avoid a misdiagnosis, first make sure that the noise is not originating from
outside the vehicle.
Troubleshoot noise problems in order of loudness, starting with the loudest noise.
Setting the radio to a frequency that receives no signal may make recognition of the noise
problem easier.
OK: The noise source can be determined.
NG: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
OK: REPAIR OR REPLACE NOISE SOURCE
NO SOUND CAN BE HEARD FROM SPEAKERS
Condition in Which Noise Occurs
Noise Type
Depressing accelerator pedal increases noise, and stopping engine
stops noise immediately
Generator noise
When A/C or heater is operating
Blower motor noise
When rapidly accelerating on unpaved road
When ignition switch is turned ON
Fuel pump noise
When horn switch is pressed and released
When horn switch is pressed and held down
Horn noise
Running engine causes soft noise, and stopping engine stops noise
immediately
Ignition noise
Noise occurs synchronously with turn signal flash
Flasher noise
Noise occurs during window washer operation
Washer noise
Running engine causes noise, but stopping engine does not stop
noise
Engine coolant temperature
sensor noise
When wiper is operating
Wiper noise
When brake pedal is depressed
Stop light switch noise
Other
Static electricity on vehicle
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
INSPECTION PROCEDURE
1. CHECK SOUND SETTING
a. Enter the sound adjustment screen by pressing the "SOUND" switch on the AUDIO display.
Fig. 339: Identifying Audio Setting
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Set volume, fader, and balance to the initial values and check that sound is normal.
OK: Sound returns to normal.
HINT:
Sound quality adjustment items vary depending on the type of the amplifier.
NG: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE )
OK: END
CD CANNOT BE EJECTED
INSPECTION PROCEDURE
1. PRESS "EJECT" AND CHECK OPERATION
a. Press the CD eject switch in the display for 2 seconds or more and check that the CD ejects.
Fig. 340: Identifying CD Eject Switch
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: CD ejects.
NG: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
OK: Go to Next Step
2. REPLACE CD WITH ANOTHER AND RECHECK
a. Replace the CD with a normal one and check that the CD ejects.
OK: CD ejects.
NG: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
OK: CD IS FAULTY
CD CANNOT BE INSERTED OR IS EJECTED RIGHT AFTER INSERTION
INSPECTION PROCEDURE
1. CHECK IF PROPER CD IS INSERTED
a. Make sure that the CD is an audio CD or a CD with a MP3 or WMA file, and that the CD is not
deformed, flawed, stained, burred or otherwise defective.
OK: CD is a normal audio CD.
HINT:
Translucent or uniquely-shaped CDs cannot be played.
Commercial audio CDs can be played.
CD-DA files on CD-ROMs, CD-Rs, and CD-RWs can be played.
MP3 and WMA files on CD-ROMs, CD-Rs and CD-RWs can be played.
For details on playable CDs, refer to the Owner's Manual .
NG: CD IS FAULTY
OK: Go to Next Step
2. CHECK THAT CD IS INSERTED PROPERLY
a. Check whether or not the CD is inserted upside down.
OK: CD is properly inserted.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
NG: INSERT CD PROPERLY
OK: Go to Next Step
3. CLEAN CD
a. Clean the disc by wiping the CD's underside radially with a soft cloth.
Fig. 341: Cleaning Disc Surface With Soft Dry Cloth
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Malfunction disappears.
NG: Go to step 4
OK: CD WAS DIRTY
4. REPLACE CD WITH ANOTHER AND RECHECK
a. Replace the CD with a normal one and check if the same problem occurs again.
OK: Malfunction disappears.
NG: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
OK: CD IS FAULTY
CD SOUND SKIPS
INSPECTION PROCEDURE
1. CLEAN CD
a. If the disc is dirty, clean the disc by wiping the CD's underside radially with a soft cloth.
NOTE:
Do not use a conventional record cleaner or antistatic preservative.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст