Toyota Tundra. Manual — part 148
Fig. 35: Service Check Mode And Detailed Information Diagnostic Mode Flow Chart
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Press the preset switch "3" to change to "Detailed Information Mode".
c. Identify the component which has stored this code.
Component table:
COMPONENT TABLE
HINT:
"440 (stereo component amplifier)" is the component which has stored this code in the
example shown in the illustration.
Component
Physical address
Stereo component amplifier
440
"Bluetooth" handsfree module
19D
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
For details of the DTC display, refer to "DTC CHECK / CLEAR" .
4. CHECK COMPONENT WHICH HAS STORED THIS CODE
a. Select the component which has stored this code.
HINT:
The "Bluetooth" handsfree module is built into the radio receiver. If there is a problem between the
"Bluetooth" handsfree module and radio receiver, replace the radio receiver.
Component table:
COMPONENT TABLE
A: REPLACE RADIO RECEIVER (see REMOVAL )
B: REPLACE RADIO RECEIVER (see REMOVAL )
A: Go to Next Step
5. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMPONENT WHICH HAS
STORED THIS CODE)
HINT:
For details of the connectors, refer to the "TERMINALS OF ECU" .
a. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the radio
receiver and the component which has stored this code.
1. Disconnect all connectors between the radio receiver and the component which has stored
this code.
2. Check for an open or short in the AVC-LAN circuit between the radio receiver and the
component which has stored this code.
OK: There is no open or short circuit.
Component
Proceed to
"Bluetooth" handsfree module (for Column Shift Type)
A
"Bluetooth" handsfree module (for Floor Shift Type)
B
Except "Bluetooth" handsfree module
C
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 36: AVC-LAN Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to Next Step
6. REPLACE RADIO RECEIVER
a. Replace the radio receiver for column shift type (see REMOVAL ) or floor shift type (see
REMOVAL ).
OK: Same problem does not occur.
NG: REPLACE COMPONENT WHICH HAS STORED THIS CODE
OK: END
DTC 01-E0 REGISTRATION COMPLETE INDICATION ERROR; DTC 01-E3 REGISTRATION
DEMAND TRANSMISSION; DTC 01-E4 MULTIPLE FRAME INCOMPLETE
DESCRIPTION
DTC TROUBLE DETECTION CONDITION
HINT:
Even if no fault is present, this trouble code may be stored depending on the battery condition or engine start
DTC
No.
DTC Detection Condition
Trouble
Area
01-E0 "Registration complete" signal from the master device cannot be received.
-
01-E3
The registration demand signal from the slave device is output. Or the registration
demand signal is output by receiving connection confirmation signal from the sub-
master device.
-
01-E4 The multiple frame transmission is incomplete.
-
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
voltage.
INSPECTION PROCEDURE
HINT:
After the inspection is completed, clear the DTCs. These DTCs do not indicate a malfunction.
DTC 01-E2 ON / OFF INDICATION PARAMETER ERROR
DESCRIPTION
DTC TROUBLE DETECTION CONDITION
INSPECTION PROCEDURE
HINT:
After the inspection is completed, clear the DTCs.
1. REPLACE RADIO RECEIVER
a. for Column Shift Type:
Replace the radio receiver (see REMOVAL ).
b. for Floor Shift Type:
Replace the radio receiver (see REMOVAL ).
NEXT: END
DTC 57-47 BLUETOOTH MODULE INITIALIZATION FAILED
DESCRIPTION
DTC TROUBLE DETECTION CONDITION
INSPECTION PROCEDURE
DTC No.
DTC Detection Condition
Trouble Area
01-E2
The command for ON/OFF control from the master device has a problem.
Radio receiver
DTC No.
DTC Detection Condition
Trouble Area
57-47
When one of following conditions is met:
"Bluetooth" module is not installed.
Problem with "Bluetooth" module
Problem in communication line to "Bluetooth" module
Radio receiver
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст