Toyota Tundra. Manual — part 1361
STANDARD VOLTAGE SPECIFICATION
Fig. 100: Identifying Opening Relay (C/OPN)
NG : Go to step 14
OK : Go To Next Step
8. CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM, FUEL
PUMP ECU)
a. Remove the circuit opening relay (C/OPN) from the engine room relay block.
b. Disconnect the A24 ECM connector.
c. Disconnect the R7 fuel pump ECU connector.
d. Measure the resistance according to the value (s) in the table below.
Standard resistance
STANDARD RESISTANCE SPECIFICATION
Tester Connection
Switch Condition Specified Condition
C/OPN relay (2) - Body ground Ignition switch ON
11 to 14 V
C/OPN relay (5) - Body ground Ignition switch ON
11 to 14 V
Tester Connection
Condition Specified Condition
C/OPN relay (1) - A24-48 (FC)
Always
Below 1 ohms
C/OPN relay (3) - R7-4 (+B)
Always
Below 1 ohms
C/OPN relay (1) or A24-48 (FC) - Body ground Always
10 kohms or higher
C/OPN relay (3) or R7-4 (+B) - Body ground
Always
10 kohms or higher
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
Fig. 101: Identifying A24 ECM & R7 Fuel Pump ECU Connectors
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR
OK : Go To Next Step
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
9. CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
a. Disconnect the R6 fuel pump connector.
b. Disconnect the R8 fuel pump ECU connector.
c. Measure the resistance according to the value (s) in the table below.
Standard resistance
STANDARD RESISTANCE SPECIFICATION
Fig. 102: Identifying R6 Fuel Pump & R8 Fuel Pump ECU Connectors
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR
OK : Go To Next Step
Tester Connection
Condition Specified Condition
R6-4 (B2) - R8-1 (FP)
Always
Below 1 ohms
R6-5 (E2) - R8-2 (FP-)
Always
Below 1 ohms
R6-4 (B2) or R8-1 (FP) - Body ground
Always
10 kohms or higher
R6-5 (E2) or R8-2 (FP-) - Body ground Always
10 kohms or higher
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
10. INSPECT FUEL PUMP
a. Inspect the fuel pump. (See INSPECTION ).
NG : REPLACE FUEL PUMP . (See FUEL PUMP ).
OK : Go To Next Step
11. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
a. Disconnect the R7 fuel pump ECU connector.
b. Disconnect the A24 ECM connector.
c. Measure the resistance according to the value (s) in the table below.
Standard resistance
STANDARD RESISTANCE SPECIFICATION
Tester Connection
Condition Specified Condition
R7-1 (FPC) - A24-52 (FPC)
Always
Below 1 ohms
R7-2 (DI) - A24-18 (DI)
Always
Below 1 ohms
R7-3 (E) - Body ground
Always
Below 1 ohms
R7-1 (FPC) or A24-52 (FPC) - Body ground Always
10 kohms or higher
R7-2 (DI) or A24-18 (DI) - Body ground
Always
10 kohms or higher
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст