Toyota Tundra. Manual — part 217
OK: REPLACE COMBINATION METER (See REMOVAL )
CELLULAR PHONE VOICE CIRCUIT BETWEEN RADIO RECEIVER AND STEREO
COMPONENT AMPLIFIER
SYSTEM DESCRIPTION
This circuit is used when the cellular phone voice in the "Bluetooth" handsfree system is on.
WIRING DIAGRAM
Fig. 233: Cellular Phone Voice Circuit Between Radio Receiver And Stereo Component Amplifier -
Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - STEREO COMPONENT
AMPLIFIER)
a. Disconnect the K3 receiver connector.
b. Disconnect the K15 amplifier connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
K3-11 (IVO+) - K15-23 (II1+)
Always
Below 1 ohms
K3-12 (IVO-) - K15-22 (II1-)
K3-11 (IVO+) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Fig. 234: Identifying K3 And K15 Connectors Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE (see PROBLEM SYMPTOMS TABLE )
MICROPHONE CIRCUIT BETWEEN MICROPHONE AND RADIO RECEIVER
DESCRIPTION
This circuit sends a microphone signal from the microphone to the radio receiver. It also supplies power from
the radio receiver to the microphone.
WIRING DIAGRAM
K3-12 (IVO-) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 235: Microphone Circuit Between Microphone And Radio Receiver - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (TSW- - SGND)
a. Disconnect the K9 receiver connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Tester Connection
Condition Specified Condition
K9-3 (TSW-) - K9-6 (MGND) Always
Below 1 ohms
K9-3 (TSW-) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 236: Identifying K9 Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Go to next step.
2. CHECK HARNESS AND CONNECTOR (MICROPHONE - RADIO RECEIVER)
a. Disconnect the W7 microphone connector.
b. Disconnect the K9 receiver connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Tester Connection
Condition Specified Condition
W7-10 (ACC) - K9-7 (MCVD)
Always
Below 1 ohms
W7-9 (MIC+) - K9-2 (MIC+)
W7-8 (MIC-) - K9-1 (MIC-)
W7-10 (ACC) - Body ground
Always
10 kohms or higher
W7-9 (MIC+) - Body ground
W7-8 (MIC-) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст