Toyota Tundra. Manual — part 161
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Fig. 66: Identifying J45 Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Go to Next Step
3. INSPECT STEERING PAD SWITCH ASSEMBLY
Fig. 67: Inspecting Steering Pad Switch Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Disconnect the z3 switch connector.
b. Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the
steering pad switch assembly connector.
c. Check if the illumination for the steering pad switch assembly comes on.
OK: Illumination for the steering pad switch assembly comes on.
NG: REPLACE STEERING PAD SWITCH ASSEMBLY (see REMOVAL )
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
OK: Go to Next Step
4. INSPECT SPIRAL CABLE
a. Disconnect the z3 switch connector.
b. Disconnect the J45 cable connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPLACE SPIRAL CABLE (See REMOVAL )
Tester Connection
Condition
Specified
Condition
z3-8 (EAU) - J45-4
(EAU)
Spiral cable is turned 2.5 rotations
counterclockwise
Below 1 ohms
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
z3-5(IL+2) - J45-12
(IL+2)
Spiral cable is turned 2.5 rotations
counterclockwise
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
CAUTION: The spiral cable is an important part of the SRS airbag system.
Incorrect removal or installation of the spiral cable may prevent
the airbag from deploying. Be sure to read the PRECAUTION for
the SRS (see PRECAUTION ).
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 68: Identifying z3 And J45 Connectors Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Go to Next Step
5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)
a. Disconnect the K3 receiver connector.
b. Disconnect the J45 cable connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Tester Connection
Condition Specified Condition
K3-6 (SWG) - J45-4 (EAU) Always
Below 1 ohms
K3-6 (SWG) - Body ground Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 69: Identifying K3 And J45 Connectors Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE (see PROBLEM SYMPTOMS TABLE )
6. CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER)
a. Disconnect the K1*1 or K4*2 receiver connector.
HINT:
*1: for Built-in Type Amplifier System
*2: for Separate Type Amplifier System
b. Measure the voltage according to the value(s) in the table below.
Standard voltage:
for Separate Type Amplifier System
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Switch Condition
Specified Condition
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст