Toyota Tundra. Manual — part 1744
b
Remove the 4 nuts, front water by-pass joint and 2 gaskets
Fig. 41: Locating Front Water By-Pass Joint And Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
11
REMOVE AIR TUBE
a
Disconnect the No 2 and No 3 hoses
Fig. 42: Locating No. 2 And No. 3 Hoses
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Disconnect the air pump connector
c
Disconnect the air pump connector clamp's holder
d
Using a clip remover, detach the wire harness claw
e
Remove the 2 bolts and air tube
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FBE) - Tundra
Fig. 43: Locating Air Tube Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
f
Disconnect the 2 No 1 air hoses from the air tube
12
REMOVE AIR SWITCHING VALVE ASSEMBLY
a
Disconnect the knock sensor connector
b
Remove the bolt and bracket
c
Disconnect the 2 air switching valve connectors
Fig. 44: Locating Air Switching Valve Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d
Remove the 3 bolts and air switching valve
Fig. 45: Locating Air Switching Valve And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
13
REMOVE NO. 2 AIR TUBE
a
Remove the 2 bolts, No 2 air tube and gasket
NOTE:
Be careful not to damage the installation surface of the gaskets.
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FBE) - Tundra
Fig. 46: Locating No. 2 Air Tube Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
14
REMOVE NO. 3 AIR TUBE
a
Remove the 2 bolts, No 3 air tube and gasket
Fig. 47: Locating No. 3 Air Tube Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION
1
INSPECT AIR SWITCHING VALVE ASSEMBLY
a
Measure the resistance according to the value(s) in the table below
Standard Resistance
RESISTANCE REFERENCE
NOTE:
Be careful not to damage the installation surface of the gaskets.
Tester Connection
Condition
Specified Condition
1 - 5
20°C (68°F)*
4 5 to 5 5 ohms
1 - Body ground
Always
1 Mohms or higher
5 - Body ground
HINT:
*: Make sure that the air switching valve is at ambient temperature before measuring the
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FBE) - Tundra
Fig. 48: Inspecting Air Switching Valve Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
If the result is not as specified, replace the air switching valve assembly
b
Check the operation of the air switching valve
1
Check that air does not flow from port A to port B
If the result is not as specified, replace the air switching valve assembly
resistance
NOTE:
When applying voltage, do not touch terminals 2, 3 and 4.
NOTE:
Make sure the applied pressure is 30 kPa (0.3 kgf/cm
2
, 4.4 psi)
or less
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст